Question about 2006 Dodge Sprinter

1 Answer

The tramission will not change out of low gear and can't manuel shift either

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Transducer is bad .

Posted on Jun 16, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 2006x5 transmission failure program light comes on and tramission wont shift gears and will not switch over to manual

You need the system control module scanned for fault codes, when it is turned on a fault code is set in memory

Aug 10, 2016 | Cars & Trucks

2 Answers

1997dodge caravan trans had no problems until I drove over a bumpy rail road track now b or second gear has low no rev .if I'm in low Manuel shift to second GOS into neutral. shift back too...

Have you checked for auto transmission fluid level? It needs to be Mopar ATF +4 ONLY, no other brand will work correctly. Check for major leaks. Check tranny for tranny codes NOT cel codes.

Feb 13, 2015 | 1997 Dodge Caravan

1 Answer

Transmission shift trouble

Top off ATF on level ground.

Jan 16, 2014 | 2000 Chrysler Town & Country

1 Answer

WHen under load the motor revs up and it seems that the Clutch is slipping, it has 100000miles and I suspecting the clutch or the high / low range might be messed up, its a 4 plus 3 manuel transmission.

If it feels like the clutch is slipping, chances are it is. If there was a problem in any component that has internal gears, you would have grinding noises. Gears cannot slip. As the clutch wears more you may hear grinding when you try to change gears but that is because the clutch won't fully disengage so the gears are spinning too fast to shift properly. Before that happens, have the clutch replaced.

Aug 02, 2011 | Chevrolet Corvette Cars & Trucks

1 Answer

1996 K 1500 with manuel four wheel floor shift will work in four low but will not work in four high (what could be the problem). Dan

so the front driveshaft turns in 4 low? or you just feeling gear reduction in 4 low?if the front drive shaft will not turn in 4 or 4low then suspect a shift fork broken. when i say turn i mean under engine power.

Sep 30, 2010 | 1996 Chevrolet K1500

1 Answer

How do I use the shift on th fly 4wd system. I wanted to know basicalll what was the procedure. Do I put the tramission in a certain gear before I shitft the 4wd system or what?

If the system is a true shift on the fly you will be able to shift in 4WD while driving in forward gear, shifting in to 4WD high only. To shift in to 4WD low you should stop the truck and place it in to park or neutral. Also as you shift in to 4wd (or out of) try to do in a neutral state with the drive train, meaning not when you are accelerating or under heavy load. Make the shift when you are more or less cruising. PLease remember true 4WD should not be run on clear concrete or asphalt as the system must be allowed to slip. If you traveling on a snow covered road or such be certain to shift back to 2WD when on clear roads to avoid drive train damage.
I hope this may have helped,

Oct 10, 2009 | 1996 Mitsubishi Montero

1 Answer

Would 1994 explorer automatic tramission work in a 1995

No it wo' nt, there is an electrical code difference between the two models that control shifting, u might get troubles of noisy/jerky shifting or being stuck in 1 gear

Sep 21, 2009 | 1995 Ford Explorer

3 Answers


This is a common problem on some GM cars. There is a pressure control valve in the side cover of the transmission that needs to be replaced. The transmission does not have to be rebuilt. You will need to get a side cover gasket also.

Nov 10, 2008 | 2003 Buick Regal

Not finding what you are looking for?
2006 Dodge Sprinter Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides