Question about 1992 BMW 3 Series

2 Answers

I need head bolt specs for a 1992 bmw 325 i - 1992 BMW 3 Series

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 869 Answers

Check with a bmw dealer. its an old one. tough to find it.

Posted on Feb 03, 2011

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points
    MVP:

    An expert that got 5 achievements.
    Governor:

    An expert whose answer got voted for 20 times.
    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 88 Answers

I presume you want torque setting. If so here is

BMW 6 cylinder engine
According to my manual as follows:

cyl head to engine block
stage 1 30nm(22ft-lb)
stage 2 + 90 degrees
stage 3 + 90 degrees

cyl head to lower timing chain cover 10nm (89in - lb)

Loosening sequence is from oustside to inside crossover and tightning from inside to outside.

Posted on Aug 06, 2009

  • johnz1313 Aug 06, 2009

    I presume you want torque setting. If so here is



    BMW 6 cylinder engine

    According to my manual as follows:



    cyl head to engine block

    stage 1 30nm(22ft-lb)

    stage 2 + 90 degrees

    stage 3 + 90 degrees



    cyl head to lower timing chain cover 10nm (89in - lb)



    Loosening sequence is from oustside to inside crossover and tightning from inside to outside.

  • johnz1313 Aug 06, 2009

    I presume you want torque setting. If so here is



    BMW 6 cylinder engine

    According to my manual as follows:



    cyl head to engine block

    stage 1 30nm(22ft-lb)

    stage 2 + 90 degrees

    stage 3 + 90 degrees



    cyl head to lower timing chain cover 10nm (89in - lb)



    Loosening sequence is from oustside to inside crossover and tightning from inside to outside.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

6ya.com

6ya - Get Instant Help

6ya.com

Need repair answers fast Use 6ya to...

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 Bmw x5 valve cover torque specs

valve cover gasket torque spec? - Bimmerforums

www.bimmerforums.com/.../showthread.php?...valve-cover...torque-spe...
Dec 7, 2012 - Remember the little rubber grommets around the cover bolts? ... Location: alabama; Posts: 5,537; My Cars: 2002 bmw 325 ... Torque spec for the M52 valve cover bolts is 89 inch-pounds / 7.4 ... 1976 - 1989 (E24) · 2004+ (E63, E64) ... 2012+ X1 (E84) · 2003+ X3 (E83,F25) · 1999+ X5, X6 (E53, E70, E71). Valve Cover Bolt Torque Specs
Oct 25, 2014
Valve cover screw torque specs?
Nov 9, 2012
leaking valve cover gasket
Dec 29, 2011
How specific for torque specs?
Dec 27, 2011
More results from www.bimmerforums.com

Nov 06, 2015 | Cars & Trucks

1 Answer

Steps to change a valve cover gaket on a 1992 ford ranger
its not very hard at all. once you get the heads off just make sure you follow the proper sequence to tighten the bolts. always remember to tighten from the center bolts out to the end bolts so the heads seat flat and even. and make sure you have the proper torque specs for those head bolts. 1) hand tighten. 2) torque to half of the OEM spec. 3) full torque spec. all of this takes a while to do so be patient.

Sep 27, 2013 | 1992 Ford Ranger

1 Answer

I need 1992 dodge spirit L4 Head specs.
Get a HAYNES or CHILTON manual. Is has all tghe steps and tightening torque values. The usual tightening sequence is to start at the center bolt, follow with the center one opposite to it, then follow an spiral going out until you reach the last bolt. As usual, you need to do it in three steps, with a decent torque wrench.

Oct 11, 2012 | 1992 Dodge Spirit

1 Answer

Describe your BMW 2001 325 Problem car hesitates
this problem could be cause by a few things, the first thing to check would be the operation of the air fuel sensor and the next thing i would look at would be to check for proper fuel preasure. the preasure spec is 50psi. and the volume spec is that it should pump at least 1.85 L in 30secs.

Mar 02, 2010 | 2001 BMW 325

1 Answer

What are the torque specs for intake and head for a 1992 c 1500 chevy silverado. I need to know the torque specs for intake and head for my engine
For 1988-1995 4.3L,5.0L and 5.7L intake manifold bolts are torqued to 35ft.lbs.Start with center bolts on each side moving out finishing with the bolts in the front of the motor and the back

Oct 24, 2009 | 1992 Chevrolet C1500

1 Answer

Im trying to do the head gasket on my 1992 bmw 325 is it possible to get to it without taking out the motor
Yes, you can. you will have to take the rocker cover off. first, undo the hose's from the cylinder head. take of the HT lead [ make you HT lead with numbers 1 to 6] Number one sparkplug closest to the radiator.

Jul 13, 2009 | 1992 BMW 3 Series

1 Answer

I need torque specs for head bolts on 1992 merc benz 230 e
hello,230e with engine 102.982,cylinder head bolt,double hexagonal socket m12, stage 1, 55 newton meter,stage 2 90 degrees stage 3 90 degrees,4 pcs. bolt with m8 tighten to 25 nm.ref. technical data year 1993,ty

Apr 17, 2009 | 1992 Mercedes-Benz E-Class

1 Answer

Head bolt settings for 1992 bmw 318i
If its a 1.8L,
oil bolts,
Tighten following correct sequence - in 3 steps,

rear 7 5 1 3 9 front of head
10 4 2 6 7

Step1 22 ft lbs,
Step2 then angle tighten 90deg,
Step3 then angle tighten 90deg again.

Nov 27, 2008 | 1992 BMW 3 Series

1 Answer

Head bolt touqe settings
Tightening torques

Do not reuse the bolts as they may be stretched.

Cylinder head to engine block
Stage 1: 32Ft-lbs
Stage 2: +90degrees
Stage 3: +90degrees

Cylinder head to lower timing
chain cover: 89in-lbs

Nov 27, 2008 | 1992 BMW 3 Series

1 Answer

1992 BMW Cylinder head
30nm 90 degrees, 90 degrees Renew bolts!!

Jun 16, 2008 | 1996 BMW 318

Not finding what you are looking for?

View Most Popular

1992 3 Series

  • Cars & Trucks

Related Question

2004 Bmw x5 valve cover torque specs

  • Cars & Trucks

Open Questions:

0 Answers

hi, does the diff of a 1997 E36 fits onto my model

Mar 16, 2015 | 1992 BMW 3 Series

0 Answers

hi i want to remove the ignitionkey for my bmw e ignition ,key bmw E36 1998

Jul 14, 2014 | 1992 BMW 3 Series

0 Answers

cylinder head torque setting toyota avensis

Jul 11, 2014 | 1992 BMW 3 Series

0 Answers

how to deploy top on 1992 bmw 325i

May 16, 2014 | 1992 BMW 3 Series

See all 1992 BMW 3 Series Questions

Related Topics

1992 BMW 3 Series Logo

344 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

2000 BMW 3 Series

1994 BMW 3 Series

2006 BMW 3 Series

2006 BMW 3 Series

2000 BMW 3 Series

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top BMW Experts

Anthony Jones
Anthony Jones

Level 2 Expert

128 Answers

Doberman

Level 2 Expert

254 Answers

dhnguyen

Level 2 Expert

281 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...