Question about 1992 Nissan Pathfinder

1 Answer

Severe power steering leak between the pump[ pulley and pump?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 57 Answers

Sounds like the front seal.

your going to need a new pump

good luck

Posted on Jun 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Power steering pulley has a leak should i just change pulley?


the pulley does not "leak" the power steering pump however will leak. If there is a leak near the pulley than I would suspect the pump is the source of the leak.

Apr 11, 2013 | Jeep Cherokee Cars & Trucks

1 Answer

How to change vane pump o/h kit


FIRST OF ALL TURN OFF RADIO REMOVE NEGATIVE BATTERY CABLE. THEN REMOVE POWER STEERING PUMP FLUID FROM POWER STEERING PUMP.USING A HAND PUMP SIPHON. BE CAREFUL DONT GET POWER STEERING FLUID ON CAR PAINT IT WILL DAMAGE PAINT JOB.PUT A DRAIN PAN UNDERNEATH CAR TO CATCH POWER STEERING FLUID THEN DISCONNECT POWER STEERING PUMP LINES.REMOVE POWER STEERING PUMP ADJUSTER BOLT AND MOUNTING BOLT.REMOVE POWER STEERING PUMP.MOST OF THE TIME NEW POWER STEERING PUMP DONT HAVE DRIVE PULLEY ON IT SO TAKE TO A MACHINE SHOP THE WILL REMOVE PULLEY FROM OLD PUMP AND PRESS ON THE PULLEY TO NEW POWER STEERING PUMP.BESURE TO BUY NEW O RINGS TO END OF PRESSURE LINE.ONCE NEW POWER STEERING PUMP HAS PULLEY IN PLACE AND YOU HAVE NEW O RING FOR HIGH PRESSURE LINE.INSTALL NEW PUMP.ADJUST BELT TENSION.NOW BLEED POWER STEERING PUMP WITH FRONT WHEELS POINT STRAIGHT A HEAD POSITION.POUR POWER STEERING FLUID IN PUMP UNTIL FLUID LEVEL ON COLD MARK ON POWER STEERING PUMP DIP STICK.KEEP ADDING FLUID UNTIL FLUID STOP DROPPING. START THE ENGINE LET IT RUN AT IDLE ADD MORE FLUID IF DROPS KEEP FLUID ON FULL COLD MARK.ON DIP STICK TURN OFF ENGINE.CHECK TO MAKE SURE POWER STEERING PUMP NOT LEAKING AT THE LINES THEN.SAFELY RAISE SUPPORT FRONT OF THE VECHICLE WITH JACK STANDS. MAKE SURE VECHICLE ON SOLID LEVEL GROUND CHECK.FLUID LEVEL MAKE SURE AT FULL COLD MARK. NOW START ENGINE.LET IDLE MINUTE.THEN TURN STEERING WHEEL ALL THE WAY TO THE LEFT TO RIGHT SEVERAL TIMES WITH OUT STOPPING IT IN PLACE. CHECK POWER STEERING FLUID WHEN FLUID LEVEL STOP DROPPING.AND FLUID IS NOT A TAN COLOR WHICH MEAN LOTS OF AIR IN SYSTEM. TURN OFF CAR UNTIL AIR BUBBLES DISAPPEAR.CHECK FLUID LEVEL BLEED POWER STEERING AGAIN. DONT DRIVE VECHICLE UNTIL STEERING FEEL NORMAL.IF FLUID REMAIN TAN WITH AIR BUBBLES CHECK FOR LEAKS AT POWER STEERING PUMP PRESSURE HOSE ORING. AND CHECK POWER STEERING LINES TO PUMP FOR LEAKS.

Mar 07, 2011 | 2000 Honda Civic

1 Answer

How to repair a power steering pump hyundai coupe 1996


SIPHON OUT POWER STEERING FLUID.USING A HAND PUMP SIPHON TYPE YOU BUY AT ANY AUTO PARTS STORES.PLACE DRAIN PAN UNDER CAR NEAR POWER STEERING PUMP CATCH FLUID WHEN YOU REMOVE POWER STEERING LINES AT THE PUMP.REMOVE DRIVE BELT.THEN REMOVE POWER STEERING PUMP.YOU NEED TO TAKE OLD PUMP WITH YOU.TAKE NEW PUMP AND OLD PUMP TO MACHINE SHOP THEY WILL REMOVE POWER STEERING PUMP PULLEY FROM THE OLD PUMP TRANSFER PULLEY TO THE NEW POWER STEERING PUMP YOU NEED TO BUY NEW POWER.STEERING HOSES O RINGS TO GO ON NEW POWER STEERING PUMP.HOSES THE OLD ORINGS WILL LEAK. THEN TAKE NEW POWER STEERING PUMP ON INSTALL IN VECHICLE THEN BLEED POWER STEERING SYSTEM.FILL POWER STEERING PUMP UP NEW FLUID.WAIT FEW MINUTES.WHEN LEVEL DROP ADD MORE FLUID UNTIL YOU GET TO FULL COLD MARK.START ENGINE 15 SECONDS SHUT OFF CHECK FOR LEAKS. NOW CHECK POWER STEERING AGAIN ADD TO FULL COLD MARK.NOW RAISE FRONT WHEELS OFF GROUND.START ENGINES TURN STEERING LEFT TO RIGHT WITH OUT STOPPING IT DO SEVERAL TIMES THEN CHECK FLUID.ADD TO THE COLD MARK DONT OVER FILL.IF FLUID LOOKS TAN HAS AIR BUBBLES IN SYSTEM WAIT A WHILE UNTIL FLUID SETTLE CHECK FLUID LEVEL.DONT DRIVE VECHICLE UNTIL STEERING FEELS NORMAL.AND IF YOU HEAR NOISES.LOCATE PROBLEM FIX BEFORE DRIVING VECHICLE.

Jan 24, 2011 | Hyundai Genesis Coupe Cars & Trucks

1 Answer

Changeing a power steering pump


CHANGING POWER STEERING PUMP YOU HAVE TO PLACE A DRAIN PAN UNDER THE VECHICLE. SIPHON OUT POWER STEERING FLUID WITH A SIPHONER DONT USE YOUR MOUTH TO SIPHON SWALLOWING POWER STEERING FLUID CAN BE FATAL MAKE YOU SICK.WHEN ALL POWER STEERING FLUID IS REMOVED FROM POWER STEERING PUMP.REMOVE DRIVE BELT.THEN REMOVE THE POWER STEERING PUMP.THEN YOU HAVE TO REMOVE THE POWER STEERING PUMP PULLEY THE NEW POWER STEERING PUMP DONT HAVE A PULLEY YOU HAVE TO HAVE REMOVE PULLEY FROM THE OLD POWER STEERING PUMP.YOU NEED A PUMP PULLEY REMOVER AND A PULLEY INSTALLER.YOU CAN TAKE OLD POWER STEERING PUMP AND NEW POWER STEERING PUMP TO A MACHINE SHOP.THEY WILL REMOVE PULLEY OFF OLD PUMP PRESS IT ON NEW POWER STEERING PUMP.THAT WOULD BE CHEAPER THAN BUYING THE PULLER AND INSTALLER.GO TO AUTO PARTS STORE BUY NEW HIGH PRESSURE LINE O RING GOES TO PRESSURE LINE GOING INTO POWER STEERING PUMP.ONCE YOU GET NEW PUMP READY PULLEY BEEN PRESSED ON.TAKE POWER STEERING PUMP HOME PUT IT ON. BLEED POWER STEERING SYSTEM.WHAT YOU DO WHEN YOU GET NEW PUMP INSTALLED HIGH PRESSURE LINE IN PLACE.PUMP BOLTED IN DRIVE BELT ON POUR POWER STEERING FLUID IN POWER STEERING PUMP UNTIL FLUID LEVEL STOP DROPPING AND YOUR LEVEL ON POWER STEERING DIP STICK AT COLD LEVEL.NOW START CAR UP LET IT IDLE FOR 3 MINUTES.THEN TURN OFF ENGINE CHECK POWER STEERING FLUID IF FLUID LEVEL DROP ADD LITTLE MORE UNTIL LEVEL ON DIP STICK ON COLD MARK DONT OVER FILL.NOW SAFELY RAISE SUPPORT FRONT OF VECHICLE. START THE ENGINE.TURN STEERING WHEEL FROM ALL THE WAY FROM LEFT TO RIGHT DONT STOP LOCK WHEEL .GO LEFT TO RIGHT SEVERAL TIMES.THEN TURN OFF ENGINE CHECK FLUID LEVEL.IF ALL IS GOOD LET VECHICLE BACK DOWN LET IT SIT FOR A WHILE CHECK FLUID AGAIN.DONT DRIVE VECHICLE IF POWER STEERING PUMP MAKE NOISES OR YOUR STEERING FEEL STIFF HARD TO TURN.JUST MAKE SURE FLUID LEVEL RIGHT AND DRIVE BELT TIGHT GOOD LUCK.

Nov 02, 2010 | 1999 Oldsmobile Alero

1 Answer

Cant find were to put powersteering fluid


Power Steering Pump Removal & Installation 3.8L Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Place a drain pan under the vehicle.
  3. Remove the accessory drive belt from the power steering pump pulley.
  4. Raise and safely support the vehicle.
  5. Remove the right front tire and wheel assembly.
  6. Remove the hoses from the power steering pump.
  7. Remove the mounting bolts and the power steering pump from the engine.
  8. Remove the reservoir and pulley from the pump if necessary.
To Install:
Power steering pump removal/installation (3.8L engine) gm-08-38-480.gif

  1. If removed, install the power steering pump reservoir and pulley on the power steering pump.
  2. Position the power steering pump to the engine and install the mounting bolts. Tighten the bolts to 25 lb ft (34 Nm).
  3. Install the pressure and return hoses to the pump.
  4. Install the right front tire and wheel assembly.
  5. Lower the vehicle.
  6. Install the accessory drive belt.
  7. Fill and bleed the power steering system.
  8. Inspect the system for leaks.
  9. Remove the drain pan from under the power steering pump area.
3.4L Engine To Remove:
  1. Place a drain pan under the power steering pump.
  2. Remove the coolant reservoir.
  3. Remove the pulley from the power steering pump.
  4. Remove the wiring harness near the power steering pump and place it out of the way.
  5. Disconnect the fluid hoses from the power steering pump.
  6. Remove the mounting bolts from the power steering pump and remove the pump.
To Install:
Power steering pump removal/installation (3.4L engine) 88008g71.gif

  1. Position the power steering pump assembly to the engine and install the mounting bolts. Tighten the mounting bolts to 25 lb ft (34 Nm).
  2. Install the wiring harness in its original position.
  3. Install the pulley on the power steering pump.
  4. Install the coolant reservoir.
  5. Fill and bleed the power steering system.
  6. Inspect the system for leaks.
  7. Remove the drain pan from under the power steering pump.
prev.gif next.gif

Sep 18, 2010 | 2000 Chevrolet Impala

2 Answers

Power steering pump, broken, how to replace


Power Steering Pump - REMOVAL & INSTALLATION

3.0L OHV (2 valve) Engine
(see Figures 1 and 2)

1f2a309.jpg

Fig. 1: Power steering system-3.0L OHV (2-valve)

0111341.jpg

Fig. 2: A few special tools are required to remove and install the pulley on the power steering pump
  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belt.
  3. Remove the alternator.
  4. Drain and remove the radiator coolant recovery reservoir.
  5. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  6. Remove the idler pulley from the power steering pump support.
  7. Remove the bracket mounting bolt located under the belt tensioner mounting.
  8. Remove 2 retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  9. Clamp the pump support bracket in a suitable vise.
  10. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the 3 bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.
To install:
  1. Install the power steering pump to the power steering pump support.
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 17-24 ft. lbs. (23-32 Nm).
  4. Complete the installation by reversing the removal procedure.
  5. Fill the power steering reservoir with power steering fluid.
  6. Connect the negative battery cable.
  7. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.

Hope this helps.

Sep 06, 2010 | 1996 Ford Taurus

2 Answers

Where is the power steering dipstick


Most power steering pumps are driven by the serpentine belt and should be in plain view when the hood is open.The following shows how to remove and replace the power steering pump and might give you a clue if not in plain sight. My dad's 1998 Ford Taurus has it nearly on top, but they could have changed things in the mean time: Power Steering Pump Removal & Installation Power Steering Pump (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Remove the alternator.
  5. Drain and remove the radiator coolant recovery reservoir.
  6. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  7. Remove the idler pulley from the power steering pump support.
  8. Remove the belt tensioner.
  9. Remove the bracket mounting bolt located under the belt tensioner mounting.
  10. Remove two retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  11. Clamp the pump support bracket in a suitable vise.
  12. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the three bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.
To Install:
NOTE: The pulley must be installed within 0.010 in (0.25 mm) flush with the power steering pump shaft.
Power steering pump special tools ford-08-00-401.gif

  1. Install the power steering pump to the power steering pump support. Tighten the mounting bolts to 18 ft-lb. (25 Nm).
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 24 ft. lbs. (33 Nm).
  4. Install the bracket mounting bolt located under the belt tensioner mounting.
  5. Install the belt tensioner.
  6. Install the idler pulley to the power steering pump support.
  7. Connect the hydraulic pressure and return lines.
  8. Install the radiator coolant recovery reservoir.
  9. Install the alternator.
  10. Install the accessory drive belt.
  11. Fill the power steering reservoir with power steering fluid.
  12. Connect the battery ground cable.
  13. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.
Power Steering Pump (4V) and SHO To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Drain and remove the radiator coolant recovery reservoir.
  5. Position a drain pan under the power steering pump. Disconnect the power steering pump reservoir hose and allow it to drain.
  6. Using Pulley Remover T69L-10300-B, or equivalent, remove the pulley from the power steering pump shaft.
  7. Disconnect the pressure hose from the power steering pump and allow it to drain.
  8. Remove the power steering pump retaining bolts and the pump.
To Install:
  1. Install the power steering pump and tighten the bolts 15–22 ft. lbs. (20–30 Nm).
  2. Connect the pressure hose and secure the clamp.
  3. Using a Steering Pump Pulley Replacer T65P-3A733-C, or equivalent, install the power steering pump pulley: the pulley face must be flush with the pump shaft or within 0.010 inch (0.25mm).
  4. Connect the power steering pump reservoir hose.
  5. Install the radiator coolant recovery reservoir.
  6. Install the accessory drive belt.
  7. Fill the power steering reservoir with power steering fluid.
  8. Connect the battery ground cable.
  9. Start the engine and check for leaks and proper operation. Bleed the power steering system if needed.
prev.gif next.gif

Jul 22, 2010 | 1996 Ford Taurus

1 Answer

Power steering fluid is leaking from hose or reservoir 2003 accord


HELLO! Give the area around the pump a good clean-up. Start the car, and while someone turns the steering wheel from lock to lock (several times) try and determine if the connection point of pressure line to pump is leaking. Also watch behind the pulley for fluid escaping from behind the belt pulley. If it's the connection ;
Remove, clean , and tighten. If leak is behind pulley the pump seal is defective and you'll need to but a new pump. It is less expensive to buy it from an auto parts store. But here is a tip; Stop at a dealership, have the parts dept. run your VIN to identify what your pump looks like. Take that drawing to parts store to insure your getting the correct replacement. Honda uses a multitude of of different pumps.


FixYaWIZ.............saailer

Dec 10, 2009 | 2003 Honda Accord

1 Answer

Changing power steering pump


Power steering pump special tools

519a4ae.gif
Power Steering Pump Removal & Installation Power Steering Pump (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Remove the alternator.
  5. Drain and remove the radiator coolant recovery reservoir.
  6. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  7. Remove the idler pulley from the power steering pump support.
  8. Remove the belt tensioner.
  9. Remove the bracket mounting bolt located under the belt tensioner mounting.
  10. Remove two retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  11. Clamp the pump support bracket in a suitable vise.
  12. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the three bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.

To Install:
NOTE: The pulley must be installed within 0.010 in (0.25 mm) flush with the power steering pump shaft.

  1. Install the power steering pump to the power steering pump support. Tighten the mounting bolts to 18 ft-lb. (25 Nm).
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 24 ft. lbs. (33 Nm).
  4. Install the bracket mounting bolt located under the belt tensioner mounting.
  5. Install the belt tensioner.
  6. Install the idler pulley to the power steering pump support.
  7. Connect the hydraulic pressure and return lines.
  8. Install the radiator coolant recovery reservoir.
  9. Install the alternator.
  10. Install the accessory drive belt.
  11. Fill the power steering reservoir with power steering fluid.
  12. Connect the battery ground cable.
  13. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.

Jun 28, 2009 | 1999 Ford Taurus

2 Answers

How do I repair a leaking power steering hose?


ok thees instructions that i have is for replacing the power steering pump but it has a great pic witch shows the power steering hoses i hope it helps


NOTE The following procedure requires the use of the GM Puller toolNo. J-25034-B or equivalent, and the GM Pulley Installer tool No.J-25033-B or equivalent.
  1. Disconnect the negative battery cable for safety.
  2. Remove the air cleaner assembly for access.
  3. Release tension and remove the drive belt.
  4. Remove the power steering pump pulley using a suitable puller tool.
  5. Remove the power steering pump retaining bolts, then reposition the pump as necessary for access to the hoses.
  6. Position a fluid catch pan under the power steering pump.
  7. Remove the hoses from the power steering pump and drain the excess fluid into the catch pan.
    WARNING Be sure to cap all openings in the pump hydraulic system toprevent excessive fluid spillage and the possibility of systemcontamination.
  8. Remove the power steering pump from the vehicle.

    0900c15280227d22.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Pump pulley removal and installation


    0900c15280227d23.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Exploded view of the power steering pump mounting


    0900c15280227d24.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Typical power steering pump hose routing

To install:
  1. Position the pump to the vehicle, then uncap and connect the pump hoses.
  2. Install the steering pump to the retaining bracket, then secureusing the retaining bolts. Tighten the nut to 30 ft. lbs. (41 Nm).
  3. Install the pump pulley using the GM Pulley Installer tool No.J-25033-B or equivalent. Press the drive pulley onto the power steeringpump.
  4. Hand-tighten the pivot bolt, the adjusting bolt and the washer.
  5. Install the drive belt.
  6. Install the air cleaner assembly.
  7. Connect the negative battery cable.
  8. Refill the power steering reservoir and bleed the power steering system.
  9. Road test the vehicle, then check and top-off the power steering fluid.

Apr 23, 2009 | 2001 GMC Safari

Not finding what you are looking for?
1992 Nissan Pathfinder Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...