Question about 2005 Buick LeSabre

1 Answer

How do you remove the door cover to get to the power window device? The mortor works but the window seems to be off the track.

Posted by on

  • yadayada
    yadayada May 11, 2010

    WHAT DO U MEAN BY POWER WINDOW DEVICE

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 316 Answers

Disconnect your negative battery cable. Locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Remove the interior door handles, then disconnect the wire clips to the switches. Your panel is held in place by snap in clips; use a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are pulled, pull the panel upward to remove it from the door. Install in reverse.

Posted on Jun 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 olds passanger window off track


remove door handles, then door panel (carefully), disconnect wiring carefully as you remove door panel, remove seal covered metal of door, investigate why window glass is not in track. May have get new track seal and track -- usually corrosion a the cause

Feb 05, 2015 | Cars & Trucks

1 Answer

I need to replace window mortor


1- Remove the inner door handle.2- Remove the arm rest 3- Remove the door cover and the motor can be easily remove.

Jan 17, 2011 | 2004 Panoz Esperante

1 Answer

How do you get the driver's door latch out past the window guide?


Remove all screws around the outer edge of the door panel. Carefully pry off the decorative cover behind the door handle and remove the torix screw. Lift up firmly on the door panel to remove. To reinstall, line up molded plastic hooks on back of door panel with notches in the door, push down to secure, reinstall torix screw, decorative cover and screws.
Also before you lift away the panel, you'll need to undo the electrical connectors for the power window and door locks

It is best to get the whole power window regulator assembly from the junkyard, which includes the power window motor. Cost should be no more than $40. Remove interior door trim panel by removing all screws and pulling up on the door panel. Unbolt existing window regulator assembly and slide guides from aluminum window track (you will have to uncrimp one end of track). Installation is the reverse of removal (remember to recrimp aluminum window track after reassembly). I did this repair in 45 minutes, power window worked like new. Good Luck!



Dec 12, 2010 | 1996 Chevrolet Monte Carlo

1 Answer

99 Passat driverside power window not on track. How to dismantle enter portion of the window? And determine how to place back on track.


remove the door trim,prise handle cover off remove 2 screws,remove console switches,2 screws around door card and then remove door courtesey light plug.Gently remove door card and remove any parts like door trigger etc and be gentle with door knob and once removed ther will be a steel plate covering the door.Look halfway down on the left and right and remove the black plastic/rubber lugs then lower the window untill you see the window track and the 2 bolts that secure it.Loosen the 2 bolts slightly and position window the tighten hand tight and test then tighten hand tight and a quarter turn when happy and lube with a spray inside to keep the cable happy and from snapping.assembly is reverse of what you did so take notes.

Apr 08, 2010 | 1999 Volkswagen Passat

1 Answer

The drivers side rear window does not work. It does side down, and when the power switch is press the motor turns on. could the window be off its track or does the window unit need replaced?


It sounds like the window may be off its track. All that needs to be done is to remove the inner door panel. Be careful to pry the clips very gently. They break easily. However, most auto parts stores carry replacements. Once the door panel is off, remove the plastic sheeting that covers the door frame. It's attached with a mastic adhesive.
Once you have a clear view of the window rail, carefully pull the pane up and set the glass on the track. You may need to apply some silicone in the track to keep the glass in place.

Then, test the alignment by pressing the power button and roll the window up and down. With the window closed, replace the plastic sheeting and the door panel.

That should do it.

Oct 09, 2009 | 1994 Lincoln Town Car

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

2 Answers

Cable fell off track


You will need to Remove the Door Panel. Look for Screws and Screw Hole Covers first. Start at the Bottom of the Panel and work your way up. There are Holes in the Door Behind this that will allow Access to the Window and Components. Just look and see if the Glass is Off Track. If it is Use Clear Silicone and Reinsert the Glass. Roll it up all the Way and wait 24 hour or more for it to Dry before you roll it down again. If it is a Belt or something, You will be able to see it. If it is gone, Reach down inside the Door at the Bottom and Locate it.

Jan 23, 2009 | 2004 Jeep Liberty

1 Answer

My 2003 Forester driver side window wont work.


You need power window regulator as the cable of the regulator is out its place ,

  1. Remove the gusset cover.
  2. Pull up the inner door handle cover toward you to remove the upper hook. Pull down it to remove the lower hook. Remove the inner door handle cover.
  3. Remove the power window switch assembly.
  4. Using a trim panel remover, remove the clips of the trim panel.
  5. Remove the speaker.
  6. Using a spatula, remove the door sealer.
  7. Remove the outer mirror assembly.
  8. Remove the front end of the door weatherstrip and gusset.
  9. Remove the stabilizers.
  10. Remove the rear end of the door weatherstrip (inner and outer).
  11. Operate the power windows switch so the bolts from the regular assembly are visible through the service holes. Remove the mounting nuts.
  12. Take out the door glass. CAUTIONDo not turn the regulator in closing direction after removal of the glass. Otherwise gear may be disengaged.
  13. Loosen the nuts to remove the rear sash.
  14. Disconnect the power window motor wiring harness.
  15. Loosen the four bolts and two nuts to pull out the regulator assembly.
  16. Remove the screws to remove the motor from the regulator assembly.
  17. Installation is the reverse order of removal.0759a6d.jpg23cb1e4.jpg

Good luck...

Oct 21, 2008 | 2001 Subaru Forester

Not finding what you are looking for?
2005 Buick LeSabre Logo

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...