Question about 2001 Hyundai Accent

1 Answer

Brake peddle very hard and a load clicking noise from abs pump and there are loads of fault codes stored in abs.had them cleared but they came strait back.servo working OK and when the abs warning light is on the brake peddle seems normal so its only very hard until the abs shuts down and it seems like the hydraulic pressure isn't getting to the calipers because you can stand on the brake peddle and then suddenly the free up an then will skid.

Posted by on

  • silver top May 11, 2010

    hifrom uk for your info there was a problem and re call of hyundai accents/getz back in 2004/5 ?? concerning a problem with abs unit it was to change the wire loom to abs apparently there was a fault with the wiring mainly earth wire corrosion check out if this shows up in the service schedule? in the service book also there should be a sticker on the a post of door adjacent to hinges indication recall check + done hope this helps ?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 776 Answers

Replace the HECU (ABS Hydraulic module).

Posted on Jun 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why is the abs light in my 1994 camero stuck on is it serious


HELLO,IS YOUR ABS STILL WORKING..TEST BY DRIVING ON SOME DIRT,APPLY BRAKES HARD.IF PEDAL PULSATES AND KEEPS TIRES FROM SKIDDING THAN ABS IS WORKING..AND YOU HAVE A BAD SENSOR ON ONE OF YOUR WHEELS..OR IT COULD MEAN TIME FOR A BREAK JOB..BUT YOUR BREAKS AREN'T NOTHING TO TAKE LIGHTLY SO GO GET THEM CHECKED BY A PROFESSIONAL..ASAP..

Feb 22, 2015 | Cars & Trucks

1 Answer

Abs motor pack


You have valves in the abs block altho the motor might be working it could the valve is not working is the load sensing vavle working on the rear axle. Check the master cylinder is pumping fluid to the pump then check if fluid is coming from the from abs pump when brake peddle is applied. Ps don't forget you might have to bleed brakes once the pipes have been slackened

Apr 07, 2014 | Pontiac Grand Am Cars & Trucks

1 Answer

2007 GMC Canyon ABS Fault - Originally ABS Fault started when making a sharp right turn. (ABS Fault light only). Stopping and restarting would clear 'fault' until next hard right. Later, occasional metal...


id check your caliper to see if the piston is compressing all the way if not check your fluid it should be clean not brown or if you have been through large amounts of water if it has gotten into the brake system and check your bleeder valve to check if it has rotted or come lose or if you have a break in the lines or air, most likely your caliper is failing to compress.

Nov 05, 2013 | 2007 GMC Canyon Crew

1 Answer

Pulsating brakes and peddle pushing back up


This is a classic ABS problem. Either the pump or the ABS controller. But as it is causing the brake pedal to push back you should get it seen by a qualified mechanic and DON'T drive it until it is fixed.

Jul 15, 2013 | 2002 Chevrolet Silverado

1 Answer

The ABS light is on and off. when it is on it will make a feeling of the front tires rolling under the car then the light will come on. you feel it in the peddle also with movement toward the floor while...


sounds like you have a abs sensor failing to read a signal on one wheel , car thinks that the wheel has locked up and as you press the brake it cuts the abs in and tries to release the brakes which is the noise your hearing and poss pulling to one side as you brake untill computer recognises a fault and shuts down the abs system which is when the abs light comes on, this pulling may indicate which one is faulty, it will need a abs sensor or signal ring on the drive shaft,usually a front one ! a damaged wheel bearing can cause an interupted signal to that sensor, failing that your abs pump is faulty, hopefully not the pump as this is very expensive

Jun 24, 2011 | 2000 Ford Focus

1 Answer

My 2004 prius abs and brake light came on and the the brakes became very hard and constant beeeep noise, so i would shut the car off and pump the breaks and it would work fine so i decided to bleed the...


well, a hard firm pedal, usually indicates a bad brake booster or a vacuum leak to booster or the vacuum check valve, on booster. TO TEST BRAKE BOOSTER; pump brakes several times with engine off to deplete stored vacuum. turn on engine with pushing slightly on pedal. you should feel the pedal fade away a bit and then become firm, but not hard. if you feel nothing at the pedal when engine starts the booster is at fault. good-luck !!

Feb 03, 2011 | 2003 Toyota Prius

2 Answers

I relaced all brake pads on 2003 buick bleed brakes very little air my brake peddle still spungy and anti brake light stays on


you must re-bleed the system properly, especially the back brakes. Bring your vehicle to a local autozone to reset the ABS light or check for an ABS fault code and post it on fixya!!

Sep 27, 2010 | Buick Rendezvous Cars & Trucks

2 Answers

ABS light is coming on despite having brakes done and codes cleared


If your going to do the repair yourself take the vehicle to Autozone and have them scan the ECU for the codes that are affecting your ABS. Then do the repairs the codes dictate.

May 19, 2010 | 2000 Ford Windstar

1 Answer

2001 Chev blazer, brakes have been bled, peddle


You probably have air between the master cylinder and the abs pump. Fill the reservior and have someone pump the brake and bleed the primary lines at the abs pump. Good luck.

Apr 19, 2010 | 2001 Chevrolet Blazer

Not finding what you are looking for?
2001 Hyundai Accent Logo

396 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...