Question about 2006 Ford Escape

Open Question

Headlight warning chime not working on ford escape

My headlights are on warning chimes, as well as my instrment cluster lights stopped working at the same time

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: Arter I put on Seat Belt, another chime goes on for 6 rings,then stops

HI.
ON Ford cars and Suv's,
Some times the sound chime after the seat belt buklet.
Is like a open door.
The problem on this car is that the the DOOR AJAR SWITCH. come danaged. and the Body cumputer don't recievethe door close signal.
But is intermitent.
The door ajar switch is on the door lacth.
You only can get front the dealer.
OK. I hope this information can be useful for you.

Thank you.

Posted on Jul 17, 2008

Ad
  • 11 Answers

SOURCE: 2001 Ford Expy gear shift stuck in park

can you put in in neutral with the key on?...if not its a

Posted on Sep 11, 2008

motor1258
  • 6674 Answers

SOURCE: warning chime continues to chime as I drive

My guess is a faulty switch at door for turning off interior lights/door closed, which is giving chime that door is still open

Posted on Dec 21, 2008

  • 93 Answers

SOURCE: Need to replace headlight assembly on 2005 Ford Escape

ithere are 4 bolts that hold it in...the top 2 are obvious..the others are behind the bumper. the bumper must be removed to acces them...here are the manuals instructions..

n0037234.gif
Item Part Number Description 1 — Headlamp assembly bolts (3 required) 2 — Headlamp assembly nut 3 13008 Headlamp assembly 4 14290 Electrical connectors
Removal and Installation
NOTE: Make sure the headlamp switch and the ignition switch are in the OFF position.

  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 3 headlamp assembly bolts.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the headlamp assembly nut and the headlamp assembly.
    • Disconnect the electrical connectors.
    • To install, tighten to 5 Nm (44 lb-in).
  1. To install, reverse the removal procedure.

Posted on Jun 10, 2009

  • 6 Answers

SOURCE: headlight went out in 2003 ford escape i have

you have to remove the whole headlight assembly, then pop off the front cover pull the old bulb out and put the new one in. reverse the process to re-install. there is a small plastic tab on the topfront of the headlight assembly, that is what you need to release to get the clear cover off and get inside.

Posted on Oct 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chime doesn't work, When you leave the key in the ignition and door open, no chime. When you turn the truck off with the headlight on, no chime. Also when you open the drivers door, no interior lights


Common problem for a Ford. I found with mine having that and multiple other low voltage problems it came down to the body computer. Don't skip over the easy things first though. The fuse, the chime itself and a grounding wire.

Apr 27, 2016 | 2004 Ford Explorer Sport Trac

1 Answer

How do i disconnect fuse to seat belt alarm tried three time method didnt work


The seat belt warning chime is controlled by the central timer module ! You can't just disconnect fuses , other things may stop working !
Safety Belt Warning Indicator Lamp and Chime
The safety belt indicator and chime feature is controlled by the CTM. The driver safety belt switch is hardwired to the CTM. If at any time during the first 60 seconds after the ignition switch is placed in position II, if the driver safety belt is sensed as being unfastened, the CTM will process the input, and in turn, output a signal to the CTM through a hardwired circuit. In turn the CTM will output a visual warning to the instrument cluster. If at any time during the first six seconds after the ignition switch is place in position II and the safety belt is not fastened, the safety belt warning chime will sound.
When the seat belt is connected the warning still chimes ? Could have code stored in the CTM .
B1464 Safety belt switch circuit short to battery CTM Go To Pinpoint Test B .
SoW

Jun 30, 2015 | 2002 Ford SVT Focus

1 Answer

How to Eliminate annoying Intermittent Warning Chimes from a 1994 Continental Instrument Cluster?


This is the simplest & easiest fix, to make your '94 Cont. drivable, without having to listen to incessant CHIMES beeping every five minutes, due to faulty sensors and electrical glitches from the junk message system. Go under the dash, on the right side of the steering column and remove the plug (10 wires) from the 'warning chime module.' There is a tan/yellow wire in that plug on pin #7--that is the "tone generator" wire. CUT IT.!!! Now, when all of those faulty inputs try to get to the warning chime module--they CAN'T! Problem solved--no more beeping. This does not disrupt the chime from sounding if you open the door with your keys in the ignition, or with the lights still on--it continues to protects you from THAT. Remember to watch your OWN coolant & oil levels--to make sure no REAL problems exist--and you're good to go!

Dec 29, 2014 | 1994 Lincoln Continental

1 Answer

2005 jeep wrangler when i turn lights on beeping starts


did you RTM read the operators guide yet,
it tells you why all beeps beep and what lamps flash, (warning) and why. did you?
you turn on, the head lights, (what about 1st click , parking lights"?)
and does the dash cluster, show warnings of any kind?

if a door is ajar the system will think, you are exiting veh. with lights on and tell you, buy beeping ,etc.
but on my jeep it says on the dash DOOR, or on EVICs, (not yours)
the newer car even tells what door IS AJAR.
mine on shows , "DOOR"
the operator guide will say, check all doors for ajar, and get warning clear before driving....etc.

if you lost the guide here it is for free

http://justgivemethedamnmanual.com/jeep/jeep-wrangler-owners-manuals/

click the 05 link
ignore beeps, there are just too many .. i look at the cluster and learn to read it..
my newer jeep 08 can produce 1000s of errors,,,,, possible.
in fact the intent it to beep to tell the driver to look at the cluster
for in depth, causes.
see chapter starting on page 136'

once sound it makes is Check gauges chime. so check them.
and headlamps left on
and door ajar.

page 63
NOTE: If the driver's door is left open, and the headlights
or parking lights are left on, the "High Beam
Indicator Light" will flash and a chime will sound.
Lights-On Reminder
If the headlights or parking lights are on after the ignition
is turned off, a chime will sound when the driver's door

its a crude system, and evolved to complex in 2007.
"DOOR" or RF-door , on mine.
or

NOTE: A tone will chime if the turn signals are left on
for more than 1 mile (2 km).

search manual for
"chime will sound"

Mar 21, 2014 | 2005 Jeep Wrangler

1 Answer

I just bought a 2003 Ford F150, and a warning chime goes off right after starting. Chimes 5 times, pause, and repeat 4 more times. There are no lights or codes displayed on the dash. It drives fine, but...


The warning chime of 5x5 is a sign that the SRS ( airbag ) light is burnt out, and there is an error with the SRS system.

Verify SRS ( airbag ) lamp operation, turn the key from off to run ( do not start ) the airbag lamp should illuminate. If not, it is burnt out. Need to pull the cluster and replace.
( thread at F150online.com on cluster removal in the how to forum - titled about changing cluster illumination color or installing a cluster overlay ).

Once you replace the SRS bulb, you will get a LFC ( light Flash Code ) of a 2 digit number.
Example :
flash flash flash flash { short pause } flash flash { longer pause } flash repeats the same for 5 times, the solid on.
This is an example of a LFC 4-2. Once you have the LFC start a new problem with the LFC and we can get that fixed after you get the bulb replaced.

Aug 23, 2011 | 2003 Ford F150 Regular Cab

1 Answer

What fuse do i pull to stop the warning dings for the headlights ,key in ignition, and seat belt sounds


there is what they call a chime module . located on the drives side in or near the fuse box by the lower kick pannel . this module could be about 2x2 color black/green/or tan . and look like it has a small speaker grill in it . remove this and it should stop the warning chimes

Mar 06, 2011 | 1996 Ford Ranger SuperCab

1 Answer

I am in the Army and away from home attending a course and my wife calls me to inform me that a steady warning chime is going off inside the truck. When I asked to hear the chime it sounds to me like it...


The headlight switch turns on the courtesy light when twisted. Tell her to make sure that the headlight switch is twisted off the indent. If this isn't it, it may be the body control module.

26fe158.gif

Oct 20, 2010 | 2001 Chevrolet Blazer

Not finding what you are looking for?
2006 Ford Escape Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...