Question about 2004 Hyundai Santa Fe

Open Question

Location of canister purge valve

Also if its the same as the purge control valve

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

maklean
  • 1665 Answers

SOURCE: location of Charcol Canister and

The evaporative emission canister purge solenoid valve is a duty control type, which controls the flow of purge air from the evaporative emission canister.
4a6acf4.gif Inspection 1. Look for loose connections, sharp bends or damage to the fuel vapor lines. 2. Look for distortion, cracks or fuel leakage. 3. After removing the EVAP canister, inspect for cracks or damage. 0e0e1be.gif

Posted on Sep 04, 2008

ghost4548
  • 776 Answers

SOURCE: Location of the Purge Control Valve for 2003 Hyundai Tiburon

There were two different engines which were installed in the 2003 Tiberon... the 2.0 liter 4 cylinder:
22c99c7.jpg

And the 2.7 Liter V6:
cb31feb.jpg

Posted on Jun 06, 2009

  • 580 Answers

SOURCE: Location of the Purge Control Valve for 1998

The correct "Hyundai" term for the valve that's attached to the Vapor Canister is the "Canister Control Valve".Why don't you try to clean the old one first. They get clogged with little bits of charcoal from the canister. It's simple so see if it's bad, take it off, and try to blow through the canister side with no electric going through. You shouldn't be able to blow because the valve is supposed to be closed. If you can blow it's because the valve is clogged and hanging open. If it is clogged, you might try and clean it.

Then take the hose off from the canister and clean the hose too, you'll get a handful of charcoal out before your done. If you don't clean the hose out, you'll probably clog the valve again, even if it's new.

That's why they usually change the canister and the valve at the same time. It gets clogged because you fill the tank to the max, it floods the canister with gas, and the charcoal floats up through the hose to the valve.

Posted on Jul 11, 2009

leedavidian
  • 1420 Answers

SOURCE: where is the purge control valve located on a 2002

Welcome to FIxYa.com


f07dd68.png


Regards, Lee Davidian


Thank you for using FixYa.com

Posted on Oct 29, 2010

c_dyer01905
  • 24 Answers

SOURCE: need location of vapor canister and purge valve in

The Canister Is located on the rear drivers side under the car (Big black box with 3 rubber lines). And the purge valve is located on the in the center on the back of the intake manifold (2 rubber lines and 1 plug).

Posted on Nov 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is purge valve located?


How to test and replace the EVAP Canister Purge Volume ...

? 13:49
https://www.youtube.com/watch?v=QnVUBYdFHGI
Mar 29, 2014 - Uploaded by CarsNToys
The EVAP canister purge control volume control valve is operated by a step motor for control of flow rate of fuel vapor fromEVAP canister.

How To Install Replace Vapor Canister Solenoid Purge ...

? 2:14
https://www.youtube.com/watch?v=TZ6ZB_acC9w
Sep 16, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/vapor-canister-purge-solenoid-valve-ac-delco- ... How To Test and Replace EVAP Canister Vent ControlValve P0446 ...

EVAP Purge Solenoid Removal - YouTube

? 4:24
https://www.youtube.com/watch?v=Xj605HENFno
Feb 26, 2008 - Uploaded by richpin06a
EVAP Purge Solenoid Removal Saturn S-series. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by ...


Dec 18, 2015 | Cars & Trucks

1 Answer

Where is the purge control valve located on 1998 nissian pathfinder


Location should be back by the fuel tank.

first off, the P1447 DTC is triggered when the EVAP control system isn't operating properly or there is a leak between the intake manifold and the pressure sensor. the parts between the pressure sensor and intake manifold are:

1. EVAP canister purge control solenoid valve
2. EVAP canister purge control valve
3. EVAP canister purge volume control valve (Part # 14930-3M201) YOU WILL HAVE TO DOUBLE CHECK ON THE PART NUMBER WITH THE DEALER FOR THE PRICE.

If you've received this P1447 DTC, chances are that the brick of charcoal in the canister has fallen apart over time, and filled the lines with charcoal. this affects parts 2 & 3 from the above list, and of course the EVAP canister (Part # 14950-1s717 $144.22). but when you replace the canister, you have to replace the EVAP canister vent control valve (part # 14935-54u06 about $100), and don't forget the o-ring (part # 16618-40u00 about $1.60) that goes between the canister and the vent control valve.

If you attack this DTC early enough, all you have to replace is the canister and vent control valve with the o-ring, which will add up to under $300 MSRP...a lot better than paying upwards of $1000 for parts and labor. Don't be scared to do it, it's actually quite simple.

D

Sep 28, 2015 | Cars & Trucks

1 Answer

Trying to locate canister purge valve solenoid on vehicle


There is a canister purge valve & a volume control purge valve on your truck. The canister purge valve is on the evap. canister itself(at the rear of veh. near the fuel tank. The volume control purge valve is located in the eng. compartment, passenger side behind Battery. You didn't mention if it's a 4 or 6 cyl.

Aug 10, 2014 | 1996 Nissan Pickup

1 Answer

Toyota echo won't start code 440 441 446


Error Code: P0440
Fault Location:
Evaporative Emission (EVAP) System - Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Soution:
Check Evaporative Emission (EVAP) System Sealing.
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.

Error Code: P0446
Fault Location:
Evaporative Emission (EVAP) System, Vent Control - Circuit Malfunction
Possible Cause:
Wiring harness.
Evaporative emission (EVAP) canister purge valve.
Engine control module (ECM).

Feb 25, 2013 | 2002 Toyota ECHO

1 Answer

How do you replace the evap. purge valve solenoid on 2005 kia sportage


The canister purge valve is a computer controlled solenoid valve that allows any stored fuel vapors in the charcoal canister to be recycled back into the engine combustion process. The valve is typically located on or near the throttle body. The canister purge valve is controlled by the power train control module (PCM). The canister purge valve is closed each time the power train computer runs the OBD-II (Onboard Diagnostic Generation II) EVAP monitoring self-test.--------------------------------------------------------------------------------
renault can clip

Jan 05, 2013 | Cars & Trucks

1 Answer

Where? and how do you replace the purge valve on a 1998 nissan maxiam


The 98 model uses a square canister located under the left rear quarter panel.
There is a canister purge control valve and a canister volume control valve, so make sure you are dealing with the right valve.
The volume control valve should be on or near the intake manifold, and the purge control valve should be near the canister.

Aug 10, 2012 | 1998 Nissan Maxima

2 Answers

Ford escort wagon 1997 code p1443 displayed. what does this indicate & where is the cannister? thank you.


P1443 - EVAP Control System / Vacuum System Purge Control Solenoid Or Purge Control Valve Fault. A fuel tank pressure change greater than minus (-) 7 inches of water in 30 seconds occurred with a purge (fuel vapor) flow at less than 0.02 pounds per minute.

Possible Causes:
  • Blocked fuel vapor hose between the EVAP canister purge valve and the FTP sensor.
  • Blocked fuel vapor hose between the EVAP canister purge valve and the engine intake manifold.
  • Blocked vacuum hose between the EVAP canister purge valve solenoid and the engine intake manifold.
  • EVAP canister purge valve stuck closed (mechanically).

  • Possible Solution:
    Check for blockages between the fuel tank, the EVAP canister purge valve, and the engine intake manifold. Check for obstructions in the EVAP canister purge valve diaphragm and ports.

    The canister is on the passengers side near the firewall if I recall correctly.

    Jan 18, 2011 | Ford Escort Cars & Trucks

    2 Answers

    Code says evaporator purge solenoid


    Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

    P0440 Evaporative emission (EVAP) system - malfunction

    Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


    P0441 Evaporative emission (EVAP) system - incorrect flow detected

    Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


    P0442 Evaporative emission (EVAP) system - small leak detected

    Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


    P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

    Possible causes: Wiring, EVAP canister purge valve, ECM


    P0444 Evaporative emission (EVAP) canister purge valve -open circuit

    Possible causes: Wiring open circuit, EVAP canister purge valve, ECM


    P0445 Evaporative emission (EVAP) canister purge valve -short circuit

    Possible causes: Wiring short circuit, EVAP canister purge valve, ECM


    P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

    Possible causes: Wiring, EVAP pressure sensor, ECM


    P0455 Evaporative emission (EVAP) system - large leak detected

    Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


    P0456 Evaporative emission system - very small leak detected

    Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor


    P0457 Evaporative emission system - leak detected (fuel cap loose/off)

    Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor


    P0458 Evaporative emission system, purge control valve -circuit low

    Possible causes: Wiring short to earth, EVAP valve


    P0459 Evaporative emission system, purge control valve -circuit high
    Possible causes: Wiring short to positive, EVAP valve


    Evaporative Emission Purge Solenoid

    Description & Operation
    The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
    During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
    The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
    Removal & Installation
    The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

    1. Disconnect electrical connector at solenoid.
    2. Disconnect vacuum lines at solenoid.
    3. Lift solenoid slot from mounting bracket for Removal & Installation.

    To Install:
    1. Position solenoid slot to mounting bracket.
    2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
    3. Connect electrical connector to solenoid.
    Purge solenoid location:

    jturcotte_65.gif
    EVAP cannister location:
    jturcotte_66.gif

    Nov 05, 2010 | 2000 Jeep Grand Cherokee

    2 Answers

    P0441 EVAP Control System Incorrect Purge Flow


    Error Code: P0441
    Fault Location:
    Evaporative Emission (EVAP) System - Incorrect Flow Detected
    Possible Cause:
    Malfunction Indicator Lamp (MIL) active.
    Evaporative Emission (EVAP) Canister Purge Regulator Valve faulty/jammed.
    Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
    Evaporative Emission (EVAP) Canister Sealing faulty.
    Pipes between Tank Breathing and Throttle Body leaky/blocked.
    Hose connection(s).
    Intake leak.
    Possible Solutions:
    Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
    Perform Output Test.
    Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
    Check Evaporative Emission (EVAP) Canister.
    Perform Basic Setting.
    Check Pipes between Tank Breathing and Throttle Body.
    VSV connector near air filter box disconnected.

    Jun 15, 2009 | 1996 Chevrolet Monte Carlo

    Not finding what you are looking for?
    2004 Hyundai Santa Fe Logo

    Related Topics:

    12 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    75817 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8180 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...