Question about 2002 Land Rover Freelander

1 Answer

Clutch pedal return too high

Clutch pedal retuns to high

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Freelander 1.8 clutch pedal height is set by the master cyl piston ram.
Circlip has broken or come lose allowing the piston to come out more.
FIX This is a sealed system. Cost from about £45.for system. Can be changed easly at the roadside 30 min no special tools needed

Posted on Mar 15, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Clutch problem the clutch pedal won't return back UP, why ?


indicates no fluid in the system or air in the system
in a hydraulic it requires fluid to make the clutch disengage and also fluid to make the pedal return from the pressure of the pressure plate
if it is a cable clutch, replace the cable as the inner cable is breaking and jamming in the case

Sep 30, 2016 | Cars & Trucks

1 Answer

Where is my clutch pedal return spring located at and where do its attach to???? 2006 volvi? s40 2.4l


It shouldn't use a spring to return the pedal, it uses hydraulic pressure to return the pedal to the rest position. If the clutch pedal isn't returning, you could have an issue with the slave or the master cylinder for the clutch.

Feb 28, 2015 | Cars & Trucks

1 Answer

Revs high when i change gear


Is it possible the clutch pedal is interfering with the throttle? Start the engine in neutral and allow it to idle. Press only the clutch pedal down and see if this increase the engine speed. If it does speed up the engine and slows back down when you release the clutch then somehow this operation is where your fault lies. If it doesn't alter the idle speed, then rev your engine and release the throttle to see if it returns to idle immediately. If it is slow to return to idle then your throttle cable could be sticking. This means when you change gear lifting off the throttle has little effect and depressing the clutch to change gear causes the engine to race as the throttle is still partially open.

Aug 23, 2014 | 2005 Ford Fiesta 1.3

2 Answers

Clutch problem


I would think you have a hydraulic clutch, so there should be a return spring on the pedal or the master cylinder.

Jan 29, 2014 | Subaru Cars & Trucks

1 Answer

Sticky clutch pedal return


lubricate clutch pedal at pivot points

Dec 28, 2013 | 2001 Audi A4

1 Answer

Vauxhall vectra sli cruise controll not working


The cruise control is normal disengaged by applying a little pressure to either the clutch or brake pedal. There are switches/sensors on the top of these pedals near the return springs. The retuns springs become weaker with time/use, so it is possible that they are not fully returning to allow disengage to reset so that it can be used again.
That is the cheapest fix and should be the first check.
The next is to cange the stalk as the switch at the end may be broken. Costwise it is relatively inexpensive for a replacement and to instal yourself. Make sure you've done the first part, or else you'll waste money and time.
Good luck.

Nov 20, 2013 | Vauxhall Cars & Trucks

2 Answers

2001 nissan pathfinder clutch mushy and clutch pedal won't return


try a different mechanic . loss of fluid is a problem that they can fix

Mar 20, 2017 | 2001 Nissan Pathfinder

1 Answer

When i clutch down at high speed the pedal stays down on my impressa


Hi i would check a few things, check the return spring on the gearbox is still there and not gone, check there isnt air in the clutch system by bleeding it, check there is correct fluid in the system if you havent already, and last if problem persists change the slave cylinder on the side of the gearbox

Apr 25, 2012 | 1999 Subaru Impreza

1 Answer

The clutch pedal sticks down when trying to engage


YOU DO NEED A NEW DISC AND MOST LIKELY A MASTER AND SLAVE HYDRAULIC CLUTCH CYLINDERS, THE STICKING MAY BE DUE TO OVER TRAVEL DUE TO THE WORN OUT DISK.

May 11, 2010 | 1998 Ford Ranger SuperCab

2 Answers

Clutch sticking on 2000 pontiac firebird trans am. clutch comes halfway up but need to pull it up the rest of the way w/my foot.


There is actually a fix for this problem. There is no return spring for the clutch being that it is hydraulic. You need to take the master cylinder out and drill the return line an 1/8th of an inch. The reason why it sticks is because the return line is too small. All the fluid is backed up and once it is cleared, the clutch will return to normal. There is an article in GM High Performance magazine online that has the step by step instructions to fix it. Hope this helps.

Aug 28, 2009 | 2000 Pontiac Firebird

Not finding what you are looking for?
2002 Land Rover Freelander Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

78267 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...