Question about 2008 Suzuki SX4

1 Answer

Locating the iat sensor on a 2003 dodge 5.9

Locating the iat sensor on a 2003 dodge 5.9 engine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Suzuki Master
  • 3,854 Answers

The IAT sensor is along the intake tube before the throttle body. If your planing to buy the performance chip from EBAY or any other place, save your money. You can go to Radio shack and it will cost you less then $3.00 for the resistor needed to make your own "performance Chip" IF you like you can use and 10K ohm potentiometer wire it through to the IAT sensor wire harness so you can adjust your timing for the type of fuel you want to use or how much performance you want out of your engine. Here is a link to the installation of the resistors and the different resistor's you can use or like me use a Potentiometer. Note if the timing is to high on hot days, the knock sensor may trigger and the engine will power down 15% till next start up. Good luck and hope this helps. http://kingenterprises.net/IAT-Timing-Tricker.htm

Posted on Jun 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the iat sensor located on a 2011 dodge challenger 3.6 liter engine


The intake air temperature (IAT) sensor is located on the intake tube. Simply lift up on the engine cover to remove the cover. Near the front of the engine on the intake air tube will be a small 2 wire sensor, this is the IAT. Lift the release tab and rotate 1/4 turn to the left to remove it.

Nate

Mar 30, 2015 | Dodge Challenger Cars & Trucks

1 Answer

How do i get to the iat sensor on a 2003 Dodge dakota 4.7L V8


The 2-wire Intake Manifold Air Temperature (IAT) sensor is installed in the intake manifold with the sensor element extending into the air stream. It sits on the left side of the engine above the Idle Air Control motor. Hope this helps.

Sep 25, 2012 | 2003 Dodge Dakota Club Cab

1 Answer

ATTEMPTING TO LOCATE THE TWO IAT WIRES IN THE MAF SENSOR PLUG TO INSTALL PREFORMANCE CHIP IN 2007 DODGE NITRO 3.7 ENGINE


ATTEMPTING TO LOCATE THE TWO IAT WIRES IN THE MAF SENSOR PLUG TO INSTALL PREFORMANCE CHIP IN a 2012 COLORADO 3.7 engine.

Jul 30, 2012 | 2006 Chevrolet Colorado

1 Answer

I have a dodge caravan, started up fine, ran 5 seconds then dies. Go to restart, no crank. Came back a few hours later. Started up just fine, 5 seconds later dies. No crank again. Code P1193 is the only...


Diagnostic Test Code (DTC) P1193 is a manufacturer specific code (not listed in SAE J2012 as a standard generic fault code). Dodge lists the code definition as "Inlet AIr Temperature (IAT) Sensor Voltage High"
This code can have an affect on how your engine runs because the engine controller uses input from this sensor to adjust fuel and timing controls.

However, the symptoms you are describing do not sound like something that an IAT sensor would cause. It sounds more like your immobilizer is shutting things down (security system "thinks" somebody is trying to steal the vehicle)

I would recommend scanning your Body Control Module (BCM) and checking for active codes for your security/imobilizer system. It would probably also be wise to scan the REST of your computer network (ABS, IPC, etc.) to check for any fault codes there or network communications faults.

May 25, 2012 | 2003 Dodge Grand Caravan AWD

1 Answer

Can't find it IAT sensor 2005 dodge diesal 3500


Click the link below.It has location of IAT sensor and the instructions to remove and install iat sensor.------ http://technoanswers.blogspot.com/2011/03/where-is-iat-sensor-located-on-dodge.html ----------------------- This should help.Thanks.Helpmech.

Mar 21, 2011 | Dodge Pickup Cars & Trucks

2 Answers

I need to find the intake air temperture sensor in my dodge


depends on the engine...
3.7 liter, #1 below:

jturcotte_112.jpg

4.7 liter:

jturcotte_113.jpg

5.7 liter, #2 below:

jturcotte_114.jpg

Jan 01, 2011 | 2006 Dodge Ram 1500

1 Answer

Wher is the IAT?


the iat sensor is located in the fresh air duct connected to the air filter in front of the fuse/relay control panel. to remove the iat sensor, renive the air filter cover and using a pair of wire cutters remove the small steel band holding the sensor in place. then by pulling on sensor it will come out. when replaceing sensor be sure to install new metal ring on new sensor to secure it in place.

Apr 28, 2010 | 2005 Dodge SRT-4

1 Answer

Location of IAT sensor in the car?


For Hyundai Car 1999-05 - Intake Air Temperature (IAT) Sensor Location (check several options):

1.- The IAT sensor is located against the firewall to the left side of the engine. It is combined with the Manifold Absolute Pressure (MAP) sensor.

2.- This sensor is located in the air intake plenum assembly. On some vehicles this sensor is combined with the MAP/MAF sensor.

3.- The IAT sensor is located in the air plenum assembly. On some vehicles it is combined with the MAF sensor.

4.- This sensor is located in the air intake plenum assembly. On some vehicles this sensor is combined with the MAP/MAF sensor.

5.- This sensor is located in the air intake plenum assembly. It is combined with the Manifold Absolute Pressure (AFS) sensor.

6.- This sensor is located in the air intake plenum assembly. It is combined with the Manifold Absolute Pressure (AFS) sensor.


In the next graphic, check the position 2...

caae1be.gif

FIG : Underhood sensor locations-Elantra 2004-2005 2.0L engine


Hope this help (remember comment and rated this) TY for using Fixya.

Apr 08, 2010 | 2004 Hyundai Elantra

1 Answer

Where is the MAF Sensor and the IAT Sensor on my 99 dodge avenger, i cant seem to find these 2, if someone can kindly instruct me to find, i will be greatly appreciated


IAT is located beside the throttle. This engine does not have a mass air flow sensor the computer uses the inputs from the IAT, MAP (Manifold Absolute Pressure) sensor and the RPM reading to determine what the air flow reading would be.


Dec 24, 2009 | 1999 Dodge Avenger

1 Answer

I am looking for the I.A.T. Sensor location on my truck


If your looking for the Intake Air Temp/Manifold Absolute Pressure sensor (IAT/MAP)(2003 model year and up) It is on the top of the intake manifold, just to the left of the #3 injector fuel line. There are 2 small Torx screws holding it.

Apr 05, 2009 | 2004 Dodge Ram 3500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

430 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...