Question about Volkswagen Jetta

Open Question

Only starts when crankshaft sensor disconnected

Brt engine code

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
NismoMaster
  • 146 Answers

SOURCE: Crankshaft Position Sensor Error P0335 recurred after r&r

In the kit there are two sensor that look identical. The one for the crankshaft has a white paint mark on it near the bolt hole. Make sure that it is in the right location.

Posted on Jul 26, 2009

Ad
  • 407 Answers

SOURCE: where is the crankshaft position sensor located?

on the engine block next to the firewall

Posted on Oct 21, 2009

  • 1 Answer

SOURCE: I have just replaced the crankshaft bearings on my Suzuki Jimny M13A and found out that when I start the engine it will not stay idle. I disconnected the sensor in front of the camshaft and it stays i

dude your electronic ignition system has gone bust... you will have to replace the engine mapping chip, but good luck finding it... I tried to no avail.

Tell me if you get it though.. Goodluck :)

Posted on Jan 22, 2010

  • 1 Answer

SOURCE: Where is the crankshaft sensor located on a 2001

have you found out how to fix this problem? mine is doing the same thing now. we replaced the crankshaft sensor but now it is saying i have a misfire

Posted on Jun 26, 2010

alicantecoli
  • 22156 Answers

SOURCE: changed crankshaft position sensors without disconnecting the battery

disconnecting the battery wouldnt have made no difference ,try putting the old sensor back on and clear the codes and see what happens ,as sometimes the code comes up for no reason other than a hot car interior ,also check the part numbers on the sensors as it could be a different voltage output but dont go their as to how this can happen

Posted on Jul 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

02 explorer crank sensor went bad replaced it but will not start. cleared code but never disconnected the battery. will that make a difference


if you car was working good before, and now did not start . the way you can check the crankshaft sensor is by scanner with data readings, if you turn over the engine is going to show rpm's at the scanner, that means the crankshaft sensor is working ok.if doesn't show rpm's the sensor or the connector is defective when this sensor is defective,they cut the spark and the signal to the injectors, another tips; ecm relay,fuel pump relay,spark plugs,maf sensor, inertia switch (defective key do the same with the theft light fashing and no turn over the engine) i hope this help you.

Feb 26, 2017 | Cars & Trucks

1 Answer

The engin was running, cut out after 3min, give me code 18 and a tri angle


Hi Willem, Code 18 is a Crankshaft position sensor/Camshaft position sensor............ P0018
Crankshaft Position Camshaft Position/Correlation (Bank 2 Sensor A)
Crankshaft Position Sensor car not starting coil spark

Camshaft Position Sensor P0340 Testing and Replacement HD

Apr 30, 2016 | Cars & Trucks

1 Answer

P1336 trouble code ho to solve problem


P1336 Ford P1336 Ford - Crankshaft Position Or Camshaft Position Sensor Input Signal Error Share
0 ' Add Comment Possible causes
- Faulty Crankshaft Position Sensor
- Faulty Camshaft Position Sensor
- Crankshaft Position Sensor harness is open or shorted
- Crankshaft Position Sensor circuit poor electrical connection
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
What does this mean? When is the code detected?
The Engine Control Module (ECM) has detected a synchronization or signal error from the cam or crank sensors
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine Stall
- Engine difficult to start
P1336 Ford Description
The input signal to the powertrain control module (PCM) from the crankshaft position (CKP) sensor or the camshaft position (CMP) sensor is erratic.

Read more: http://www.engine-codes.com/p1336_ford.html#ixzz3qT9Hiztc

Nov 03, 2015 | 2005 Ford Freestyle

1 Answer

Where are the camshaft and crankshaft position sensors on 2001 silverado 8.1 V8


pic-1681384701591865649-tmb.jpegCrank shaft sensor
Remove the driver side rear ignition coil bolts. Reposition the coil. Disconnect the crankshaft position (CKP) sensor electrical connector. # Use penetrating oil and allow the oil to soak around the CKP sensor prior to removing the sensor. You're looking at left, rear side of engine.
CAMSHAFT POS.
front side of engine on the drives side about half way up the timing cover, not hard to get to.

Nov 11, 2013 | Chevrolet 3500 Cars & Trucks

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

2 Answers

Code 11. what do i check?


11 camshaft signal or ignition signal, no reference signal during cranking
If you replace the CKP sensor (crankshaft position) you will more than likely cure the problem, I'll assume you have an intermittent engine stall out or hard not start?

Nov 03, 2011 | 1995 Dodge Neon

1 Answer

Where is the crankshaft position/crank angle sensor located on a 2005 kia sedona


Hi, at the front of the crankshaft. if its near time for the timing belt, you want to replace it along with any pullies, tensioner and water pump


The crankshaft position sensor is mounted on the engine near the crankshaft.

Operation

The crankshaft position sensor is a Hall-Effect sensor that senses the crank angle (piston position) of each cylinder and converts it into a pulse signal. The signal from the sensor is relayed to the ECM to indicate engine rpm and the position of the crankshaft.

Removal & Installation

  1. Disconnect the negative battery cable.
  2. Disconnect the connector from the sensor.
  3. Remove the bolt that retains the sensor in place.
  4. Remove the sensor from its mounting. To install:
    1. Installation is the reverse of the removal procedure.
    2. Clearance between the sensor and the sensor wheel should be 0.020-0.059 inch. 2002-2005
      1. Properly connect the scan tool.
      2. Start the engine and allow it to idle.
      3. Be sure the idle position switch is ON.
      4. Specifications are as follows:

        Temperature - 4°F, test specification 1500-1700 RPM Temperature 32°F, test specification 1350-1550 RPM Temperature 68°F, test specification 1200-1400 RPMTemperature 104°F, test specification 1000-1200 RPM Temperature 176°F, test specification 650-850 RPM

Mar 16, 2011 | 2003 Kia Sedona

1 Answer

Where's the cranck sensor located?


Click the boxes with a red x in them to see diagram images. 5VZ-FE Engine
  1. Disconnect the crankshaft position sensor harness. Fig. 1: Exploded view of the crankshaft position sensor mounting 86824pa8.gif

  2. Remove the bolt retaining the sensor to the vehicle.
  3. To install, attach the sensor to the vehicle, tighten to 69 inch lbs. (8 Nm).
2VZ-FE and 3VZ-FE Engines
  1. Remove the engine under cover.
  2. Remove the alternator.
  3. Unbolt the alternator bracket.
  4. Disconnect the crankshaft position sensor harness.
  5. Remove the bolts securing the sensor and the sensor. Discard the O-ring.
  6. When installing, apply a light coat of engine oil on the O-ring, install on the sensor tighten the bolts to 74 inch lbs. (9 Nm).
1FZ-FE Engine
  1. Remove the engine under cover.
  2. Unbolt the sensor protector. Fig. 2: Exploded view of the 1FZ-FE crankshaft position sensor mounting 86824pb3.gif

  3. Disconnect the crankshaft position sensor bracket and harness.
  4. Remove the bolt, nuts and sensor.
  5. When installing, attach the sensor and tighten the bolt to 14 ft. lbs. (20 Nm) and the nuts to 78 inch lbs. (9 Nm).

Jan 28, 2011 | 1989 Toyota 4Runner

2 Answers

96 Jeep Cherokee Country will turn over fine will not start. engine light code is 121155


- Code 12, recently battery unplugged

- Code 11 Ignition reference signal
No ignition reference signal detected during cranking (bad Hall effect) OR loss of camshaft sensor (and, for cars with crankshaft sensors — which does not include the 2.2/2.5 — timing belt skipped a tooth or loss of crankshaft sensor).

Note #8 Can cause the engine to stop working entirely with no limp-home mode. Note: An anonymous poster wrote, “Code 11 will only be set upon clearing the codes, most commonly by disconnecting the battery. It says in the factory diagnostic manuals that code 11 means no ignition reference signal has been seen since battery disconnect. As soon as the vehicle's engine is cranked, and a reference signal is seen, code 11 will go away immediately on it's own. It also won't be set upon failure of a part such as a hall-effect pick-up plate, or loss of the timing belt. If no reference signal is seen during cranking after a battery disconnect, code 11 will remain. This is a helpful indicator in a no-start condition.” (Chrysler did sometimes change codes depending on the year, so it may be that some of these apply to differentyears).

- Code 55 End scan test

Check other details HERE.

Hope help with this, remember rated this help.

May 26, 2010 | Jeep Cherokee Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...