Question about Hyundai Motor 2002 Sonata

Open Question

Power antenna Motor clicks antenna will not extent all the way up

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove broken antenna


Most electric Antennas require two people to replace. First turn key on watch and listen to antenna motor as some one turns on radio do this several times. Now remove spanner nut the antenna mast goes through then have them turn radio on again this you assist the rest of the mast out of motor assembly watching what side the teeth are on the plastic cable . Now take new mast and fully extent it and lubricate with a machine oil 3 in 1 works great. slowly lower into housing trying to get first tooth hooked or close then turn radio off this will retract the antenna into the assembly hopefully on the first try it should be all the way in. don't worry re install retainer parts raise and lower several times the overrun clutching will get it in time.

Nov 09, 2013 | 1999 Ford Falcon

2 Answers

Power antenna motor won't stop running. Do you know where the cutout switch is located?


There is no switch. When the plastic gears inside the power antenna strip out they continue to run because the limiter switch inside the unit never gets tripped. If you can assist the antenna up when it's running, leave it up and disconnect the power to the motor. If i remember correctly the antenna is mounted on the passenger rear quarter panel. You should be able to pull some of the truck trim out a little and disconnect the two or three wire connector.

Jul 08, 2010 | 1993 Buick LeSabre

1 Answer

How to replace thunderbird antenna


please rate service.

Automatic Electric Antenna
Removal
  1. Lower electric antenna (18850) .
  1. Remove rear retaining screws of RH front wheel splash shield for access to antenna lower retaining bolt.
  1. Remove lower retaining bolt.
  1. Remove radio antenna nut (18865) from top of motor tube and remove electric antenna through fender/splash shield access.
  1. Disconnect signal cable and motor wire connector(s).
Installation
  1. To install, reverse Removal procedure.
  1. Tighten top radio antenna nut to 6-8 Nm (54-70 lb-in).
  1. Tighten lower electric antenna retaining bolt to 5.8-7.8 Nm (51-69 lb-in).
  1. Check operation of electric antenna and radio chassis .

    Automatic Electric Antenna


    1faf511.gif

mast
Mast, Power NOTE: A power antenna mast which is bent or broken can be replaced without replacing the motor and tube assembly.
Removal
  1. Remove radio antenna nut (18865) and radio antenna stanchion (18919) .

    ssd~us~en~file=l6389b.gif~gen~ref.gif

  1. Loosen retaining nut inside tube using 14 mm (9/16 inch) socket, and slide nut part-way up mast.
  1. Raise antenna to run plastic drive wire at bottom of mast out of motor. Note direction of teeth on plastic drive wire.
  1. Saw off damaged portion of antenna mast. Remove burrs from mast and slide nut and contact tube off stationary tube.
Installation
  1. With the teeth on the plastic drive wire facing toward motor on antenna, push end of plastic drive wire of replacement mast assembly down into tube. Push it around curve at bottom of tube until end enters drive mechanism.
  1. Run motor down while pushing on plastic drive wire until about 305 mm (12 inch) of wire has been drawn into the tube. Stop motor and insert bottom of antenna mast into tube. Lower mast.
  1. Slide contact tube and radio antenna nut down antenna mast. Tighten nut to 0.45 Nm (4 lb-in).

  2. Raise and lower antenna several times to ensure proper operation.
651247a.gif

Jul 09, 2009 | 1995 Ford Thunderbird

2 Answers

Power antenna motor will not shut off


I assume that the power antenna unit is an original equipment unit, if so.
1. Does it run for about a minute then stop? If this is the case, your antenna shaft needs to be replaced. This is a very simple procedure that your local radio install shop can do for you in about 20 minutes.
2. If the motor never shuts off as long as the key is on, you probably have a defective relay on the antenna motor. At this point you need to replace the entire unit. A job that can be a bit pricey because of the price of the unit itself. A cheeper fix is to replace the power antenna with a manually telescopic unit, (no motor), or a fixed unit, (doesn't go down). If you opt for the latter, remember to unscrew or lower the antenna in automatic car washes!

Jul 07, 2009 | 1984 Cadillac Eldorado

3 Answers

Power antenna motor on my 3000gt is out and i need instructions


Access is behind the left hand panel in the hatch/trunk area. (Your car is left hand drive, correct? Not a GTO?) Only have to remove a few screws to get to it. Then a couple more bolts to remove the antenna motor. No, they cannot be rebuilt, and new ones from Mitsu are VERY expensive. You might want to buy a generic model from Advance, Auto Zone or NAPA.

Apr 16, 2009 | 1995 Mitsubishi 3000GT

1 Answer

Power antenna slippage...


This is not a screw correcting problem. The antenna rod is connected to the motor by a rubber-like chain pully. The more you use the more it weakens which means it is designed to spoil.

You have to change it (the antenna). It would not cost much because its about $10 in my country Nigerria.

Rate this fixya

Apr 04, 2009 | 1990 Toyota Celica

2 Answers

Power antenna motor runs, but antenna doesn't


Fault in the retractor assy. Is the mast bent. If it is gently try to straighten best possible lube with silicone spray. With someone turn off the radio , try manually putting antenna down with the palm of your hand squezzed around mast and forcing. Do the same going up, pull by the end tip ,

Mar 29, 2009 | 1997 Buick Riviera

1 Answer

'95 Riv - antenna does not retract


Most power antennas have a plastic cable with teeth that feed into the power antenna motor.  I recommend replacing the antenna.  A special tool is required to remove the slotted nut where the antenna comes out of the car.  You could use something else, but be careful not to scratch your paint.  I also recommend taking apart the motor to remove any remaining broken pieces of cable.  Usually only one nut holds the cover of the antenna motor in the center. After removal of the old antenna follow these instructions: 1.  Feed the new antenna cable down into the antenna motor; teeth facing the front of the car. 2.  Have someone turn key enough to operate the radio.  You should feel the teeth raking against the teeth in the motor.  If you do not, face the teeth toward the back of the car. 3.  Have your assistant turn the radio off, and allow the antenna motor to pull in the cable.  The motor will automatically stop when it feels resistance.   4.  Return the slotted nut, so you do not have to repeat steps 2 and 3.

Dec 21, 2008 | 1995 Buick Riviera

1 Answer

Power antenna does not go all the way up, does not power retract


Does the motor continue to run even though the mast doesn't retract? Is there a loud 'click - click - click" as it tries to retract and extend or more of a chattering noise? Did you clean and lubricate the spool into which the toothed belt goes when the antenna retracts? Use an all weather grease (white lithium). Did you clean the teeth on the gear that drives the belt? There is a small metal guide where the belt meets the drive gear, sometime this wears and allows the belt to slip on the gear. Pull the giude straight out, then rotate it 180 degress and reinstall.

Jun 08, 2008 | 1993 Honda Accord

Not finding what you are looking for?
Hyundai Motor 2002 Sonata Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...