Question about 2006 Nissan Altima
Im trying to reset my alarm to a replacement I bought but I don't know where the valet push button is located
Posted by Anonymous on
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Look for alarm Brain box and look for wires coming out black and red going to valet switch. to turn valet on turn ignition in ON position and press-switch or flip depending on the type of switch. If it a basic alarm just disconnect the main wiring harness to alarm box- unplug and the car should start. Good luck and thanks for using FIX YA
Posted on Jan 27, 2009
The MAP sensor is located on the driver's side of the engine compartment next to the air filter housing and shock tower.
It is a small plastic component with one vacuum hose coming off of it and an electrical connector that has two wires. It might be advantageous to write in and let me and/or other techs know what the symptoms are prior to replacing the sensor. Sometimes just replacing the part is a waste of money. The fact that the code has indicated the problem is the MAP sensor, doesn't mean it is bad. As an example, check to see if the Vacuum hose is secure and not disconnected or split at either end.
Posted on Apr 05, 2009
YOU WILL REQUIRE DIAGNOSTIC TO DO THIS BUT IF YOUR VEHICLE IS LOCK IN A SAFE AREA JUST LEAVE ONE COMPONENT OPEN AND CHECK IF THE ALARM WILL SOUND AGAIN REPEAT THIS TILL YOU FIND THE DEFECTIVE COMPONENT.
Posted on Jul 21, 2009
You are incorrect sir. There is a very good Youtube video showing you exactly where it is that is how I changed mine. The Crankshaft is located behind the engine block below and around from the cam sensor which is easly spotted looking at the engine. The crankshaft is in a difficult spot but once you figure out where it is it's easy...ish hope this helps
Posted on Dec 10, 2009
The first objective is to figure out which bulb you need. I had to replace the bulb for the largest light which was a Sylvania 3157. The next objective is to remove the dang plastic carpet holder/net clip. Recognize that it is a two part piece. Use a flathead screwdriver for leverage. Pry the cap off by levering the screwdriver in the slot on the holder. Then go behind the carpet and pinch the plastic pin still holding the holder in place. Next,pry off the while plastic pieces from the two bolt/nuts you'll need to remove (see manual). Remove the nuts and give the two screws a push from the inside so you can see how the whole light casing comes off. Pry it off from the outside. On the backside of the bulb holder, turn bulb base counterclockwise and gently remove. Pull bulb upward and replace. Do not touch glass on new bulb with your fingers (wear non-powdered rubber gloves). Make sure the bulb snaps in place. Follow these instructions in reverse. Smile, you just learned something new and saved yourself some easy money.
Posted on Jan 09, 2010
Tips for a great answer:
Dec 03, 2015 | Nissan Cars & Trucks
Aug 04, 2012 | 2005 Nissan Altima 2.5
Jul 23, 2012 | 2008 Nissan Altima
Apr 20, 2012 | Toyota Camry Cars & Trucks
Dec 14, 2011 | 2003 Nissan Altima
Aug 25, 2011 | 2006 Nissan Altima
Feb 12, 2011 | 2005 Nissan Altima
Jan 06, 2011 | Toyota Camry Cars & Trucks
Nov 05, 2008 | 1997 Nissan.5 Altima
Sep 15, 2008 | 1997 Chevrolet K1500
91 people viewed this question
Usually answered in minutes!