Question about 2004 Dodge Ram 1500

Open Question

Spark plug stuck

Back plug on right side , cant remove it, stuck, cant see ,,hemi 5.7

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 ford windstar spark plug wires diagram


I\'m assuming you have the 3.8 engine,although i believe the firing order is the same on all there v6 sideways mounted front wheel drive Windstars. That firing order is 1-4-2-5-3-6, with 1-2-3 going from left to right on the back side of the engine and 4-5-6 left to right on the front side of the engine.Looking straight down at the coil from the front of the car,you\'ll see 2 rows of coil terminals.The row on the right side is 1-2-3 going from top to bottom,row on left side is 6-5-4 going from top to bottom. Hook the number 1 coil terminal to the number 1 spark plug ,being careful to use the spark plug wire that is closest in length to the length you need. If your just replacing wires,yuo shouldn\'t have to much trouble. If your nreplacing the spark plugs you will find the ones in the rear,especially the number 2 [the middle one} are pretty difficult without removing the cowling. A total pain brought to you by the designers at Ford!

Jun 04, 2014 | 1998 Ford Windstar

1 Answer

Describe your how fix my pontiac 2000 montana Problem changing spark plugs



Inspection

Inspect for the correct routing of the spark plug wires. Improper routing may cause cross-firing. Inspect each wire for any signs of cranks or splits in the wire. Inspect each plug wire boot for tearing, piercing, arcing, carbon tracking or a corroded terminal.
If there is any corrosion, carbon tracking or arcing indicated on a plug wire boot or terminal, both the plug wire and component it was connected to should be replaced.


Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the left side spark plug wires from the spark plugs.
  3. Remove the left side plug wires from the retaining clips.
  4. Rotate the engine for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. Remove the right side spark plug wires from the spark plugs.
  6. Remove the plug wires from the retaining clip.
  7. Remove the spark wires from the ignition coils.
  8. Remove the plug wire assembly from the engine.
    NOTE If you are replacing the spark plug wires, the spark plug wire conduit and retaining clips should be transferred to the replacement wires.

To install:
  1. Install the right side plug wires to the ignition coils and then the spark plugs.
  2. Install the spark plug wires to the retaining clip.
  3. Rotate the engine back to the original position.
  4. Install the left side spark plug wires to the ignition coils and then to the spark plugs.
  5. Install the spark plug wires to the retaining clips.

3.9L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the intake manifold cover.
  3. Remove the left side spark plug wires as follows:
    1. Disconnect the left side spark plug wires from the spark plugs.
    2. Disconnect the left side spark plug wires from the ignition coil.
    3. Remove the left side spark plug wire clips from the intake manifold and heater inlet and outlet pipe.
    4. Remove the left side spark plug wire assembly.

  4. If removing the right side spark plug wires, the engine must be rotated for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. After rotating the engine, remove the right side spark plug wires as follows:
    1. Disconnect the right side spark plug wires from the spark plugs and ignition coil.

  6. Remove the right side spark plug wire clip from the ignition coil bracket.
  7. Remove the right side spark plug wire assembly.

To install:
  1. Install the spark plug wire assembly.
  2. Install the right side spark plug wire clip at the ignition coil bracket.
  3. Connect the plug wires to the ignition coil and spark plugs.
  4. If the engine was rotated for access, return the engine to the original position.
  5. The remainder of the installation is the reverse order of removal.

Feb 05, 2011 | 2000 Pontiac Montana

2 Answers

I think i messed up my spark plug pattern...first timer!!! sorry i need help....85 gmc s15 v6 2.8ltr....


Firing order is 1-2-3-4-5-6..Cylinders are 1-3-5 Front to back on the LEFT SIDE and 2-4-6 Front to back on the RIGHT SIDE, as your standing at the fan looking at the transmission. Here is a picture:

chuckster57_10.gif

Jan 16, 2011 | 1985 GMC S-15

1 Answer

How do i put in spark plugs in my 2005 dodge ram 1500


I'm assuming this is a 5.7 hemi. Remove the 8 coil packs that are bolted to the top of the valve cover. You can do 1 at a time. Each coil pack has two spark plugs under it . use a 5/8 spark plug socket and extention. If its a 4.7 the coil packs are held on by one 10mm nut. These packs are just inside the valve cover on both sides of the engine. There will be only one 5/8 plug for each pack

Jun 25, 2010 | 2005 Dodge Ram 1500

3 Answers

I have a 2007 Dodge Ram 1500 with the 5.7 HEMI/MDS engine.If I shut the engine down when hot and then restart within a short time the idle goes up and down by about 100 RPM.It settles itself out after...


YOU COULD BE HAVING ENGINE MISFIRE.DUE TO BAD SPARK PLUGS AND WIRES.ALSO DIRTY FUEL INJECTORS WILL CAUSE ENGINE TO ROUGH IDLE OR IDLE UP AND DOWN.PUT A BOTTLE OF FUEL INJECTOR CLEAN IN A FULL TANK OF GAS.ALSO CHANGE PLUGS AND WIRES.IF TRUCK HAS 30000 TO 60000 MILES ON IT.THATS THE SCHEDULE MAINTENCE INTERVALS IF SPARK PLUGS HAS NOT BEEN CHANGED.

Feb 14, 2010 | 2005 Dodge Ram 1500

1 Answer

I need the diagram to put the spark plug cables


2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
  2. Remove the intake manifold cover, if required.
  3. Disconnect the left side spark plug wires from the spark plugs.
  4. Disconnect the left side spark plug wires from the ignition coil.
  5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
  6. Remove the spark plug wire assembly.
  7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
  8. Disconnect the right side spark plug wires from the spark plugs.
  9. Disconnect the right side spark plugs from the ignition coils.
  10. Remove the spark plug wire assembly.
  11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.
To install:
  1. Install the spark plug wire assembly.
  2. Connect the right side spark plugs to the ignition coils.
  3. Connect the right side spark plug wires to the spark plugs.
  4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
  5. Install the spark plug wire assembly.
  6. Connect the left side spark plug wires to the spark plugs.
  7. Connect the left side spark plug wires to the ignition coil.
  8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
  9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
  10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
74d742b.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
306b531.jpg


Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
9313fa7.jpg


Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system
2c9af72.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
d929c16.jpg


Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
f357cd3.jpg

Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
09e9db9.jpg

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 2003 Chevrolet Malibu

1 Answer

I replaced my spark plug wires on my 1996 chevy truck. may have crossed one,need a diagram from the spark plugs to the distributer cap.


Since you didn't state whether it is a V6 or V8, I'll give you both.

V6 -4.3Liter
Firing Order is 1-6-5-4-3-2
Distributor rotor turns Clockwise
Number 1 spark plug tower on distributor cap, faces the front of the engine.

->Drivers side, spark plug order in engine, starting from the Front going back:
1-3-5
->Passenger side, spark plug order in engine,
starting from the Front going back:
2-4-6

If it's Electronic, the distributor cap has a Left side, (Drivers side), and a Right side, (Passenger side)
Starting from the Front, going back on the Left side,
3-1-5
Starting from the Front going back on the Right side,
2-4-6

V8-5.0, 5.7, and 7.4Liter
Firing Order is 1-8-4-3-6-5-7-2
Distributor rotor turns Clockwise
Number 1 spark plug tower on distributor cap,
faces Front, towards the Drivers side.

Electronic distributor cap has two sides. Drivers, (Left), side and Passenger, (Right), side.
Starting from Front going back on Drivers side,
1-7-3-5
Starting from Front going back on Passenger side,
8-2-4-6

Spark plug order in engine, starting from Front going back, Drivers side:
1-3-5-7
Spark plug order in engine, starting from Front going back, Passenger side:
2-4-6-8

Aug 28, 2009 | 1996 Chevrolet K1500

1 Answer

Where does the firing order start on a 1991 3.8 buick lesabre. 165432


There are six VIN numbers of engines for the 1991 Buick Lesabre, with a 3.8 Liter engine.

1.Vin B
2.Vin 3
3.Vin C
4.Vin 1
5.Vin L
6.Vin K

All have the Firing Order of 1-6-5-4-3-2

For Vin B and 3:
Hood open, looking at the engine from the front of the car. The coil pack is behind the engine, close to the firewall. (Under the windshield)
The crankshaft pulley is down on the left side.

Spark plug numbering, for the spark plugs close to the radiator side.
From Left; (Front of engine), going Right-> 1-3-5
Spark plug numbering, for spark plugs on the backside of the engine.
From Left going Right-> 2-4-6

The distributorless coil pack sits on the backside of the engine, close to the firewall.
Numbering of where to put the spark plug wires;
There are three spark plug towers close to the engine. From Left to Right -> 3-5-7
There are three spark plug towers far from the engine. From Left to Right-> 6-4-2

For Vin C, 1, L and K:

Hood open, facing the car.
The Front of the engine faces to the Right. The crankshaft pulley is down, and to the Right.

Spark plugs close to the radiator;
From Left to Right-> 6-4-2
Spark plugs close to firewall, (Below windshield)
From Left to Right-> 5-3-1

The distributorless coil pack sits on the right side, in front of the engine. (The Front of the engine is on the right side. The crankshaft pulley is on the Right side)

Starting at the ->Back and coming Forward. (To the Front of the car)
On the Left side of the Distributorless Coil Pack, it is -> 4-2-6
On the Right side it is -> 1-5-3

Aug 19, 2009 | 1997 Buick Skylark

1 Answer

Can't find the spark plugs on a 2004 toyota tundra V-8


If the engine is the same as my 2002, they are a Hemi-style which go right into the valve covers, hidden under the individual coil packswhich can be removed by loosening one nut I believe. After you remove the nut, pull straight out and you will see the Spark plug cap is attacked to the bottom of the coil pack, use an extension and a spark plug socket preferably with a rubber grommet inside it or you will play hell getting the plugs out of the wells once they are loose.

Mar 02, 2009 | 2002 Toyota Tundra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...