Question about 1994 Chevrolet Astro

1 Answer

How to replace ecm

Will not run

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 161 Answers

Check the fuse for the ecm before replacing it. If you have a ford eec diagnostic try to get the codes. If you don't have a eec code reader there is a way to get the codes out by counting dashboard blinks. If you can get the ecm to output the codes the ecm is not bad.

Posted on Apr 02, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Chev Uplander 3.9 Could ECM need replaced? Where is it located?


Without testing we'd only be guessing ! You have no idea of the complexity of the electronics on your vehicle . Replacing the ECM would mean a trip back to the dealer to have it programmed . Without programming your vehicle will never start . You had new battery an alternator installed , did it start an run when you picked it up. The charging system on your vehicle is computer controlled . DTC P0621
DTC P0621 : Generator L-Terminal Circuit
The engine control module (ECM) uses the generator turn ON signal circuit to control the load of the generator on the engine. A high side driver in the ECM applies a voltage to the voltage regulator. This signals the voltage regulator to turn the field circuit ON and OFF. The ECM monitors the state of the generator turn ON signal circuit. The ECM should detect low voltage on generator turn on signal circuit when the ignition is ON and the engine is OFF, or when the charging system malfunctions. With the engine running, the ECM should detect high voltage on the generator turn on signal circuit. The ECM performs key ON and RUN tests to determine the status of the generator turn on signal circuit.

Your best bet take it back to the dealer .

Feb 25, 2018 | 2007 Chevrolet Uplander

2 Answers

I have replaced two two camshaft sensors on my 2007 Saturn outlook Xr for code 336 and no results please help


Who replaced the sensor ? You or a repair shop ? The DTC P0336 does not say to replace a sensor . You do not have access to the diagnostic trouble code diagnostic's . Your best bet ,take it to a qualified repair shop .
DTC P0336: Crankshaft Position (CKP) Sensor Performance
CKP Sensor Signal Circuit
P0335
P0335
P0335
P0336

P0336
• The ECM detects that the engine is running, but receives less than 51 or more than 65 CKP sensor pulses each engine revolution for 8 of 10 engine revolutions.
• The ECM detects that the engine is running, but more than 19 resyncs occur within 25 seconds.
• The ECM detects that the engine has been running, but the crankshaft does not sync for 0.4 second.

Oct 19, 2017 | Saturn Cars & Trucks

1 Answer

Can a faulty ECM cause engine and transmission problems?


Yes -- but to find that out you have to run the fault codes
Unless you have had a serious fault (battery connected wrong-power surge ),the ECM is the last item to check
battery was flat or replaced the normally resetting the ECM and CPU programs with a scanner will fix ECM problems.

Mar 29, 2015 | Cars & Trucks

2 Answers

I have a 1990 nissan 240sx. It sat for 10 years. 36000 miles on it. I have replaced fuel pump n filter, full tune up, ECM, all injectors and starter. It does start but will idle high but will not stay...


if you have changed the ECM it is possible that you will have to reset/reprogram the ecm to the sensors of the vehicle. Find a nissan shop that has the ability to reprogram the ecm and reset it.

Dec 27, 2014 | Cars & Trucks

1 Answer

Have had a 302 runs rough have done EGR cleaned and replace. New cap plugs wires replace vac hose to map EGR cleaned and checked tps iac fuel filter new have replaced ECM new. Every thing checks out have...


You don't give the year built, but back when ECM where first introduced it was known that the vehicle would run rough for await till the ECM had time to learn so of speak, by driving on the road. We had to drive down the road a few miles first to get running right on it's own.

May 20, 2014 | Cars & Trucks

2 Answers

Low voltage


Have you tried fixing the errors that the ECU is reporting?

Aug 13, 2012 | 2004 Nissan Sentra

1 Answer

Need to know if after replacing a faulty ECM unit with a used unit, does the replacement unit need to be professionally reprogrammed or serviced in any way?


You should just have the correct ECM and PROM inside of it.
When battery power is removed from the ECM it will reset to factory defaults. When you install it and start the vehicle it may run rough. Some drive and key cycles will "relearn" the ECM.
I have seen a number of vehicles do this just after replacing the battery.

Oct 09, 2011 | 1990 Buick Regal

1 Answer

I have a 1990 exel gls with a 1.5 4 cylinder port fuel injected. The original ecm would no longer run the engine, but will still comunicate with my scanner. I have tried 2 different ecm's which will run...


Heres a TiP for ECM malfunction!
Replace all the CAPACiTOR inside ur OLD ecm, 'cause thats the part of the circuit that breaks down!
I have repaired a LOT of ECM, and it works!
Try that if u couldn't get a NEW one!

Dec 01, 2010 | Hyundai Excel Cars & Trucks

4 Answers

97 gmc sierra no fuel no spark replaced ign module and pickup coil still no spark


1996 GMC 1500 Pickup.
Replaced Coil, Dist cap/Rotor, Ign Mod & pick-up.
All showed to be bad with OHM meter.

20A ECM-B fuse keeps blowing out and I'm afraid to burn these new parts up....

ANY IDEAS OUT THERE???

Mar 31, 2009 | GMC Sierra 1500 Cars & Trucks

1 Answer

1998 town and country. Installed a new compter now engine turns over but no start and run.


Hello
If it ran before the ecm switch then its the new ecm. If the ecm was replaced because it would not run then were looking at a different problem.
RD

Jan 12, 2009 | 1998 Chrysler Town & Country

Not finding what you are looking for?
1994 Chevrolet Astro Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...