- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Lets simply thing here. American Auto Manufacture use three wires set for it
rear light assembly. One wire to the braking switch for both stop lights, one
wire for the clearance light on both sides. Now if you look at the plug for
taillight assemble there will three wires and didn't mention the third wire,
it's ground. The two brake light uses one wire, then for on or clearance light
uses one wire, and the ground uses one wire On old automobile normal the grounds
any place on the body. But now the grounding points to make sure there isn't a
Turn signal light are a separate circuit as with the back up lights. I fairly
sure your Caddy uses a Mylar strip with copper strips on it. Find were this
copper strips are broken, scratch off the thin layer insulation and solder a
jumper wire across the broken copper strip.
There will be a Central location where these light are tied together. Left
brake light wire goes to the one wire from the brake switch under the dash, the
right brake light goes to the same tied point to brake light switch under the
dash. The Central wire point will be at one of the back lights. Just follow the
colored wire. Now, each has two colors, one solid and one strip is colored with
different colors. I hope this help you. GB stewbison
There may be extra wires you don't need. The basic set of wires on the radio is 4 pairs of colored wires--one black-striped and one plain for each speaker. Yellow is usually accessory power, red is hot, and black is ground. Some additional wires may be one for a power antenna, one for an external amplifyer, and one for facelight (in case it will run on dimmer)
The car should have the following corresponding wires:
Radio 12v--- orange Radio Ground--- black Radio Ignition--- yellow Radio Illumination--- brown Dimmer--- gray Power Antenna--- pink (if you have one) LF Speaker +/- tan - grey RF Speaker +/- lt green - dk green LR Speaker +/- brown - yellow RR Speaker +/- dk. blue- lt. blue
The car or radio could have additional connectors, such as for a subwoofer, CD changer, etc.
and there should be a diagram on the back of the kenwood deck which would explain the deck side. if not your main power should be yellow = Constant 12V for clock Red = Ignition 12V switch turn on the deck Black = Ground blue purple green white= for speakers
solid color = to positive on speakers color with black stripe = negative on speakers
I would solder and heatshrink all connections Good luck
its possible if Ur very careful u need the power wire/ ground and all the speaker wires u can identify these using a multi meter to determain which is the power wire and ground the speaker wires shoul be similair in color like solid brown then a brown with a stripe on it them solid green then a stripped green etc.
Radio Constant 12V+ Wire: White/Green Radio Switched 12V+ Wire: White/Red Radio Ground Wire: Black Radio Illumination Wire: n/a Radio Dimmer Wire: Red/Black Radio Antenna Trigger Wire: n/a Radio Antenna Location: Rear Glass Front Speakers Size and Location: 6 1/2′ Doors Left Front Speaker Wire (+): Blue/Green Left Front Speaker Wire (-): Gray/Black Right Front Speaker Wire (+): Red/Green Right Front Speaker Wire (-): Brown/Black Rear Speakers Size and Location: 6′ x 9′ Rear Deck Left Rear Speaker Wire (+): Blue/Yellow Left Rear Speaker Wire (-): Gray/White Right Rear Speaker Wire (+): Red/Yellow
1996 Eagle Vision Car Radio Wire Diagram
Car Radio Battery Constant 12v+ Wire: Black/Yellow Car Radio Accessory Switched 12v+ Wire: Red/White Car Radio Ground Wire: Black/Light Blue Car Radio Illumination Wire: Orange Car Stereo Dimmer Wire: Pink Car Stereo Antenna Trigger Wire: Orange/Red Car Stereo Amp Trigger Wire: N/A Car Stereo Amplifier Location: N/A Car Audio Front Speakers Size: 3 1/2′ Car Audio Front Speakers Location: Dash Left Front Speaker Positive Wire (+): Dark Green Left Front Speaker Negative Wire (-): Brown/Red Right Front Speaker Positive Wire (+): Purple Right Front Speaker Negative Wire (-): Dark Blue/Red Car Audio Rear Speakers Size: 6′ x 9′ Car Audio Rear Speakers Location: Rear Deck Left Rear Speaker Positive Wire (+): Brown/Yellow Left Rear Speaker Negative Wire (-): Brown/Light Blue Right Rear Speaker Positive Wire (+): Dark Blue/White Right Rear Speaker Negative Wire (-): Dark Blue/Orange
Here are the factory wire colors, please rate this solution to your problem, a note any stereo store that sells auto decks has adapter wiring harnesses to do a direct plug in of your DIN standard radio you are trying to install, no cutting of the factory harness, they are cheap
2000 Ford Taurus Car Radio Stereo Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Green/Black Car Radio Accessory Switched 12v+ Wire: Black/Pink Car Radio Ground Wire: Black/Green Car Radio Illumination Wire: N/A Car Stereo Dimmer Wire: N/A Car Stereo Antenna Trigger: N/A Car Stereo Amp Trigger Wire: N/A Car Stereo Amplifier Location: N/A Car Audio Front Speakers Size: N/A Car Audio Front Speakers Location: N/A Left Front Speaker Positive Wire (+): Orange/Green Left Front Speaker Negative Wire (-): Blue/White Right Front Speaker Positive Wire (+): Tan/Green Right Front Speaker Negative Wire (-): Green/Orange Car Audio Rear Speakers Size: N/A Car Audio Rear Speakers Location: N/A Left Rear Speaker Positive Wire (+): Gray/Blue Left Rear Speaker Negative Wire (-): Brown/Yellow Right Rear Speaker Positive Wire (+): Black/Violet Right Rear Speaker Negative Wire (-): Orange/Violet