Question about 2006 Mitsubishi Eclipse

1 Answer

How do I gain access to the electric door lock motor on 2006 Mitsubishi Eclips GS?

How do I gain access? Door panel is removed.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Mitsubishi Expert
  • 227 Answers

By removing the side panel trim

Posted on Apr 07, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the door lock motor on a 2006 Mitsubishi Eclips GS.


first take out actuator that is attached on the motor itself i believe there will be plastic connector that will join the lock and the actuator

Apr 01, 2014 | 2006 Mitsubishi Eclipse GS

1 Answer

Fuel tank filler door RELEASE LEVER will not open the fuel tank door


Fuel tank doors can be operated electrically or by cable, you say 'release lever' so that points to a cable system, if they do not open, access to the flap can be gained by removing internal trim/carpet and manually operate the lock, check if the cable is connected to the back of the lever. Good luck

Jan 23, 2014 | 2006 Mitsubishi Lancer

1 Answer

Drivers side window switch clicking


Larry if the window does not go up or down its likely that the gear driven assembly or the motor on your electric window for the drivers door is bad. You will need to disassemble the door by removing the door panel to gain access to the electric motor. Hope this helps you will want to gain access to a service manual from a local parts store to help you with this venture. Good Luck

Nov 28, 2011 | 2002 Kia Sedona

2 Answers

My Mitsubishi colt CZ1 (07 plate) has problem with cental locking. I can manually central lock but with the remote it locks/unlocks all the doors except the driver's door. Please help. Thanks


Central locking works by way of little electric motors that engages and disengages the door lock. The drivers door has an additional set of contacts in the actuator which signal the controller when it changes position. The controller activates the servo motors when a signal is received from the receiver or from the drivers door servo motor. So in your case I suspect the motor part of the drivers door actuator is done for.
To replace you will have to remove the inner driver's door panel to get at the actuator. The actuator itself cannot be repaired and needs to be replaced as a unit.

Apr 29, 2011 | 2006 Mitsubishi Colt

1 Answer

Were does the LH mirror on a 2011 f-250 connect. Removed mirror but disconnect is located some were in door or body. need to know what needs to be removed to gain access


  1. Remove the front door trim panel.
  1. Position aside the front door watershield to gain access to the exterior rear view mirror control switch electrical connector.
4.Disconnect the exterior rear view mirror control switch electrical connector
ganyapr_7.jpg
as you see you have to remove the door panel to have access to the electrical connector in case that you dont know how to do it here are the instructions

NOTE: Left front door trim panel shown, right front door trim panel similar.
  1. Remove the sail panel.
    • If equipped, disconnect the electrical connector

  2. If equipped, lift up and remove the exterior rear view mirror control switch panel.
    • Disconnect the electrical connector.
  1. If equipped, lift up and remove the window control switch panel.
    • Disconnect the electrical connector.
  1. If equipped, remove the window regulator handle.
    1. Position the window regulator handle cover aside.
    1. Remove the window regulator handle screw and regulator handle
5.Remove the door trim panel center screw cover
6.Remove the 2 door trim panel center screws
7.Remove the 2 door trim panel lower screws
  1. NOTICE: Do not pull directly outward on front door trim panel as damage will occur.
    Remove the front door trim panel.
    • Lift upward to remove the front door trim panel.
  1. NOTICE: Insert the lower panel tabs first or they can break when installing the front door trim panel.
    To install, reverse the removal procedure

Feb 20, 2011 | 2011 Ford F-250 Super Duty

1 Answer

Need to replace front door window motors


Electric Window Motor REMOVAL & INSTALLATION Ranger
  1. Disconnect the negative battery cable.
  2. Open the window. Remove the trim panel and watershield and support the window.
  3. Disconnect the power window motor connector.
  4. There may be a drill dimple in the door panel, opposite the concealed motor retaining bolt. Drill out the dimple to gain access to the bolt. Be careful to avoid damage to the wires. Remove the motor mounting bolts and remove the motor and regulator assembly.
  5. Separate the motor and drive from the regulator on a workbench.
  6. Installation is the reverse of removal.
  7. Check for smooth operation before installing the trim panel.
Except Ranger
  1. Raise the window fully if possible. If not, you will have to support the window during this procedure. Disconnect the battery ground.
  2. Remove the door trim panel.
  3. Disconnect the window motor wiring harness.
  4. There may be a drill dimple in the door panel, opposite the concealed motor retaining bolt. Drill out the dimple to gain access to the bolt. Be careful to avoid damage to the wires.
  5. Remove the motor mounting bolts (front door) or rivets(rear door).
  6. Push the motor towards the outside of the door to disengage it from the gears. You'll have to support the window glass once the motor is disengaged.
  7. Remove the motor from the door.
  8. Installation is the reverse of removal. To avoid rusting in the drilled areas, prime and paint the exposed metal, or, cover the holes with waterproof body tape. Make sure that the motor works properly before installing the trim panel.
prev.gif next.gif

Nov 12, 2010 | 1992 Ford Explorer

1 Answer

How to remove door panel to gain access w/out damaging panel?


I hope this helps , easier done than said :)
1- Remove door latch bezel. (handle) 2- You will find door trim panel retaining bolt , remove it. 3- Remove the door pull handle screw cover. 4- Remove the door pull handle retaining screws. 5- Detach the interior door trim panel ( to make removal easy , release clip by lowering glass and pressing case inwords) 6- Disconnect the door trim harness electrical connector. 7- Remove the door trim. 8- Disconnect the driver door module electrical connector 9- To install , reverse removal procedures

Jul 29, 2009 | 2000 Jaguar S-Type

1 Answer

I have a 1993 Ford Tempo and am having problems removing the motor from the door. I already have the door panel removed and the power disconnected from the motor.


remove the door panel and check to make sure the linkage to the lock assembly is still attached. I can't give an estimate because I don't know what is wrong at this point

are the locks manual or electric?i have seen most electric locks freeze up because of rust/.corrosion.the rubber accordian seal fails and moisture does it's job.there is no lubrication on the mechanism.it's basically a push pull magnet tube with a spiral grooved actuator rod.this is to assure no accidental vibration/jar induced movement.also means very difficult to budge when corroded.i have gotten a few to move by grabbing lock post with pliers and pulling hard.good luck!



Rear Door Window Regulator and Motor
Removal and Installation
Remove the rear door trim panel. For additional information, refer to INTERIOR TRIM AND ORNAMENTATION .
Remove the door mounted speaker.
Remove the watershield.
NOTE:The glass must be lowered for this step.

NOTE:Some vehicles may use rivets to attach the glass to the regulator.

Remove the bolt that attaches the glass to the regulator.
Raise and support the rear door window glass to the full up position.

NOTE:Do not detach the door handle from the latch cable during this step.

Remove the rear inside door handle.
Remove the screw.
Disengage the inside door handle from the door.
If equipped, disconnect the power door lock rod from the back of the inside door handle.

Gain access to the power window motor electrical connector located in the front of the door.
Fig. 90: Identifying Power Window Motor Electrical Connector
Courtesy of FORD MOTOR CO.
Disconnect the power window motor electrical connector.
Press down on the connector tab.
Pull the connector upward and remove through the speaker opening in the door.
Disconnect the rear door window regulator and motor assembly from the door.
Remove the nuts.
Remove the screws.
Fig. 92: Disconnecting Rear Door Window Regulator And Motor Assembly From Door
Courtesy of FORD MOTOR CO.
266999_door_2.jpg
Remove the window regulator and motor assembly from the door.
Fig. 93: Removing Window Regulator And Motor Assembly From Door
Courtesy of FORD MOTOR CO.
266999_door_3.jpg

To install, reverse the removal procedure.

Jul 01, 2009 | Ford Tempo Cars & Trucks

1 Answer

2006 ford fusion drivers door exterior hanle remove/replace


You will need to remove the door panel on the inside of the door. Then you can gain access to a couple of bolts with nuts that hold the door handle onto the body of the door. You will also need to remove an actuating rod that goes to the door lock and back to the handle. It can be quite cramped inside the door panel, but have patience and you will succeed.

May 22, 2009 | 2006 Ford Fusion

Not finding what you are looking for?
2006 Mitsubishi Eclipse Logo

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...