Question about 2004 Cadillac SRX

Open Question

Canister purge valve solenoid 2004 cadillac srx location

Where is the solenoid located on this model

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75051 Answers

SOURCE: purge vent valve for 2004 Cadillac SRX

Raise and support vehicle.• Remove right rear wheel housing liner, see Repair Manual Body Exterior Group 66 - Exterior equipment, "Rear wheel housing liner, removing and installing" in ElsaWeb.• Disconnect T-3 electrical connector at Leak Detection Pump (LDP).• Disconnect EVAP purge line, EVAP vacuum Line and EVAP vent line from EVAP canister.

Posted on Sep 07, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the vapor canister purge valve located on a 96 Cadillac deville Northstar


If your purge valve/solenoid is failing, chances are you will need a new EVAP Carbon Canister as well. As the canister gets old the charcoal (carbon) starts to break down and bits gets sucked and stuck in the valve when the gases are purged from the canister on start up and acceleration. If you take the solenoid off and tap it on the ground you will probably see tiny bits of carbon fall out. This is a sure sign that you need a new canister ...Just replacing the solenoid valve won't help as it will only get clogged again by these bits of carbon. GM located most canisters in the rear wheel well under the wheel well lining. Not too sure of your model but check a Manuel. You must also blow out the line before connecting it to the new canister as bits of carbon can be still in the line and contaminate the new purge valve.

Mar 27, 2015 | Cadillac Cars & Trucks

1 Answer

Trying to locate canister purge valve solenoid on vehicle


There is a canister purge valve & a volume control purge valve on your truck. The canister purge valve is on the evap. canister itself(at the rear of veh. near the fuel tank. The volume control purge valve is located in the eng. compartment, passenger side behind Battery. You didn't mention if it's a 4 or 6 cyl.

Aug 10, 2014 | 1996 Nissan Pickup

1 Answer

Why wont my car start after I refuel it?


run the fault codes and look for a problem in the canister purge valve/solenoid

May 10, 2014 | 2004 Cadillac SRX

1 Answer

Need to know where to find the canister purge valve


For the location of canister purge valve,check the following help links mentioned below:--
Click the link :---

Location for EVAP Purge Valve Solenoid?

http://schematicsdiagram.blogspot.in/2012/06/2002-nissandatsun-pathfinder-location.html


------------------

How to disconnect the hose form the Evap Canister?

http://schematicsdiagram.blogspot.com/2011/12/how-to-disconnect-hose-form-evap.html

-------------

2004 Chrysler PT Cruiser: Location of EVAP Purge Solenoid Valve?

http://schematicsdiagram.blogspot.in/2012/06/2004chrysler-pt-cruiser-location-of.html

-----------
These will help.
Thanks.

Jan 08, 2013 | Cars & Trucks

1 Answer

Purge vent valve for 2004 Cadillac SRX


Raise and support vehicle.• Remove right rear wheel housing liner, see Repair Manual Body Exterior Group 66 - Exterior equipment, "Rear wheel housing liner, removing and installing" in ElsaWeb.• Disconnect T-3 electrical connector at Leak Detection Pump (LDP).• Disconnect EVAP purge line, EVAP vacuum Line and EVAP vent line from EVAP canister.

Sep 06, 2012 | Cadillac SRX Cars & Trucks

1 Answer

2003 Mitsubishi Eclipse has a P0456 (sometime RD - pending) Evap small leak. Replacing gas cap did not solve. Is there a vapor canister purge valve/solenoid on this car?


There is a purge valve and solenoid on most cars I believe. The purge valve is usally located by the engine and the selenoid is usally located by the fuel tank. Call up or go visit your dealer and you will be able to order the parts from them and they can tell you the exact location.

Aug 09, 2011 | 2004 Dodge Ram 1500

2 Answers

Where is the evap purge/vent solenoid located on the Cadillac CTS 2003


It is located under the car near the gas tank on a tray with the fuel vapor storage cannister

Jul 09, 2011 | 2003 Cadillac CTS

2 Answers

Code says evaporator purge solenoid


Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

P0440 Evaporative emission (EVAP) system - malfunction

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0441 Evaporative emission (EVAP) system - incorrect flow detected

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0442 Evaporative emission (EVAP) system - small leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

Possible causes: Wiring, EVAP canister purge valve, ECM


P0444 Evaporative emission (EVAP) canister purge valve -open circuit

Possible causes: Wiring open circuit, EVAP canister purge valve, ECM


P0445 Evaporative emission (EVAP) canister purge valve -short circuit

Possible causes: Wiring short circuit, EVAP canister purge valve, ECM


P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

Possible causes: Wiring, EVAP pressure sensor, ECM


P0455 Evaporative emission (EVAP) system - large leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0456 Evaporative emission system - very small leak detected

Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor


P0457 Evaporative emission system - leak detected (fuel cap loose/off)

Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor


P0458 Evaporative emission system, purge control valve -circuit low

Possible causes: Wiring short to earth, EVAP valve


P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve


Evaporative Emission Purge Solenoid

Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

  1. Disconnect electrical connector at solenoid.
  2. Disconnect vacuum lines at solenoid.
  3. Lift solenoid slot from mounting bracket for Removal & Installation.

To Install:
  1. Position solenoid slot to mounting bracket.
  2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
  3. Connect electrical connector to solenoid.
Purge solenoid location:

jturcotte_65.gif
EVAP cannister location:
jturcotte_66.gif

Nov 05, 2010 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2004 Cadillac SRX Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...