Question about 2005 Mazda 3 1.6

Open Question

Mazda 3 2005 drive shaft bolt torque setting

Have changed a wheel baron on my mazda 3 2005 and need a torque setting shaft boltfor the drive

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 341 Answers

SOURCE: torque settings for pressure plate and fly wheel

the flywheel is 50 -60 ft.lbs....pressure plate is 15- 25 ft. lbs..

Posted on Nov 22, 2008

Ad
  • 30 Answers

SOURCE: Torque on 1994 Mazda pick up

if its a four cylinder(lets hope)the specs are 80-90ft.lbs torque.if its a six cylinder it is 14ft.lbs torqueat 90 degree intervals then repeat until correct torque has been reached.bad news is you can not use the same bolts on the six cylinder engine.have to be new to keep from breaking them

Posted on Mar 15, 2009

  • 5 Answers

SOURCE: removal front wheel bearing 2003 mazda protege

hi there, i have 2 mazda6s, both off which i needed to removed the inner axels on, so far you have done every thing right :), but unfortunatly due to mazdas sloppy assembly the inner axles are near impossible to remove, you could try getting a 2 or 3 legged puller and remove the brake calliper and disk then try and "pull" the shaft out, but unfortunatly i doubt will work. your second option would be to use a hydraulic ram to press it out, but again due to mazdas sloppy work it is near impossible with out damaging the hub, ive tryed both option and none of wich worked, so i brought 4 second hand hubs and outer C.Vs, hope this helps.

Posted on Sep 03, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

steve_e_uk
  • 1675 Answers

SOURCE: i need head bolt torque for mazda b2500 wl engine

e94d3fc.png03cad01.png
hope this helps...please vote thanks

Posted on May 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you change wheel bearing hub assembly for 2007 Dodge Caliber xlt


You need big socket could be #32 or #34 for the drive shaft, there is three bolts could be #13 or something else.have to prey out or hammer out. clean good old dirt.Don't torque more than 100 lbs!!! drive shaft.

Apr 30, 2017 | Dodge Cars & Trucks

1 Answer

How to install a torque converter in a 2000 2.5Lt on Ford ranger 2 wheel drive?


You need to remove the transmission to do this. Remove the inspection cover at the junction of the engine and transmission to get to the bolts to disconnect the torque converter from the drive plate (the part with teeth that the starter engages). Remove the driveshaft, then the transmission. The torque converter will come out with the transmission. Pull the old torque converter from the transmission, and install the new one. Ensure the torque converter goes all the way into the transmission/hydraulic pump. Reinstall the transmission, ensuring that the torque converter is still free to turn during the entire installation process, especially while drawing up the transmission to the engine. Once the transmission is bolted up, reinstall the bolts holding the torque converter to the drive plate. Reinstall the drive shaft and the inspection cover.

If you haven't done any major mechanical work on a car before, seek the help of someone who has. You will need a hoist or a jack and jack stands, and a good set of tools.

Nov 03, 2016 | Ford Cars & Trucks

1 Answer

How to pull 2002 mazda tribute trans


Pull the drive shaft, (4 wheel drive) remove the transfer case, Put a jack under it and support it, remove the mount nuts, jack it up, remove the cross member, remove the starter and any covers in front, remove the torque converter nuts/ bolts, Lower it, keeping it supported some what. Remove the bell housing bolts. Jack it up a little and slide it back. Lower it and remove all the electrical connectors. remove the shifter cable. Pull it out and replace. You really need a manual for this job. Good luck.

Apr 14, 2015 | Mazda Cars & Trucks

1 Answer

Need torque settings for mazda xa 3.0l diesel 4 cyl


con rod bolt tension is 55-60ft/lbs
crank shaft main bearings is 80-85 ft/lbs
fly wheel bolts95-100 ft/lbs
crank shaft pulley nut 94-123 ft/lb
head studs tension 80-95 ft/lbs working in a spiral direction from no 1 stud directly in the centre of the head. Pull down in 10ft/lb increment starting at 20 ft/lbs
valve clearance is .010" both valves cold but after warming engine and re-tensioning the head studs re set valves to .012 both valves
injector retaining nuts tension12-17 ft/lbs

Dec 25, 2013 | Saab 9 Cars & Trucks

1 Answer

Drive shaft bolts are lose?


Does your drive shft spin and not the wheels?

Jun 20, 2013 | Cars & Trucks

1 Answer

Changing front axle assembly or wheel hub or both? Either way, need torque specs for all bolts.


you've got a bad axle shaft in the front and possibly a bad bearing in the hub. 4/wheel drive makes the front axle actually work. Theys no real pressure on these shafts when in 2/wheel drive.

Feb 01, 2013 | 2002 Chevrolet Silverado 1500

1 Answer

TORQUE SETTING ON FRONT WHEEL BEARING NUT ON 2006 PONTIAC TORRENT


Hello, here is the torque spec for front hub bearing
Strut to Steering Knuckle Bolt and Nut
180 N·m
133 lb ft
Tie Rod Retention Nut
50 N·m
37 lb ft
Wheel Bearing/Hub Mounting Bolt
130 N·m
96 lb ft
Wheel Drive Shaft Spindle Nut
205 N·m
157 lb ft

Nov 07, 2010 | 2006 Pontiac Torrent

1 Answer

I have a 99 mazda protege, 1.6l engine, automatic transmission. I am changing the CV joints out and I need the torque specification for the axle spindle nut that connects the cv joint to the wheel hub.


hi the torque settings for the hub nuts are 236-318 Nm these are the drive shaft nuts that fit on the end of the shaft on the wheel hub hope that's what you required please rate and vote thanks

Sep 20, 2010 | Mazda Protege Cars & Trucks

2 Answers

1995 4wd mazda b series/cv joint/drivers side


HOW TO REMOVE WHEEL BEARING ON MAZDA PICKUP 1995 B3000

Jul 13, 2008 | 1995 Mazda B-Series

1 Answer

Need help


start off in order
remove earth from battery
remove
starter motor
drive shafts
clutch slave
bellhousing bolts
if auto remove torque converter bolts
wiggle out gearbox

Jun 29, 2008 | 1995 Mazda 626

Not finding what you are looking for?
2005 Mazda 3 1.6 Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...