Question about 2004 Volkswagen Touareg

Open Question

7L6121156 RADIATOR HOSE

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I drain my radiator on a 2005 envoy Denali


If there is not a pit **** on the bottom or side of the radiator by the lower hose you will need to loosen the lower radiator hose and gently work the lower radiator hose off at the radiator and drain it into a drain pan. If not at the lower radiator and if the water pump connection for the hose is easier to work on you can loosen the clamp on the hose there and pull the radiator hose back and drain it from there. Once it is drained push the hose back in place and tighten the hose clamp. Refill the radiator slowly as not to get an air lock in the radiator, also once you think it is filled start the truck and leave the radiator cap off until the thermostat opens and add more antifreeze to top it off. Hope this helps.

Mar 14, 2017 | 2005 GMC Envoy Denali

2 Answers

Instructions to remove radiator in 1999 isuzu Rodeo and install new one


remove items in this order and fit in reverse
1st-grill to help with access
2nd-cooling fan
3rd-fan shroud
4th-radiator hoses x3
5th-radiator
remember to remove the rubbers at the bottom of the old radiator to use on the new radiator

Dec 02, 2016 | Isuzu Cars & Trucks

2 Answers

How do replace radiator hose


As car repairs go, a radiator hose is one of the easier jobs.

Get a replacement hose.

Wait for the engine to be cold.

Loosen the hose clamps at each end of the hose.

Use a heavy screwdriver if needed to loosen the hose from the radiator and engine. Pull the hose off both ends.

Put new hose on, with the clamps. Tighten the clamps.

Fill the radiator with coolant as needed.

done.

Oct 01, 2015 | Cars & Trucks

1 Answer

Steps on removing and replacing radiator on my 1999 jeep cherokee sport 6 cyl. stright


Things You'll Need
  • Waste oil collection pan
  • Needle nose pliers
  • Phillips head screwdriver
  • Wrench set
  • Socket set
  • Antifreeze
  • Water
armor-all-tyn2.png
  1. Draining the Cooling System
    • 1 Locate the petcock valve on the lower right corner of the radiator and place a waste oil collection pan underneath it.
    • 2 Open the petcock valve by turning it counterclockwise, using needle nose pliers.
    • 3 Wait until all the coolant has drained out then close the petcock valve by turning it clockwise.
    Removing the Radiator
    • 1 Loosen the hose clamp that connects the upper radiator hose to the radiator using a Phillips head screwdriver. Then pull the upper radiator hose off the radiator.
    • 2 Loosen the hose clamp that connects the lower radiator hose to the radiator using a Phillips head screwdriver. Then pull the hose off the radiator.
    • 3 Unscrew the transmission cooler lines from the radiator (automatic transmission only) using a wrench.
    • 4 Unscrew the bolts that secure the radiator to the core support, using a socket.
    • 5 Lift the radiator straight up to remove it from the vehicle.
    Installing the Radiator
    • 1 Lower the radiator into position behind the core support. Be careful: the cooling fins are thin and can be easily damaged.
    • 2 Screw the bolts that secure the radiator into the core support. Tighten with a socket.
    • 3 Thread the transmission cooler line fittings into the radiator. Tighten with a wrench.
    • 4 Slide the lower radiator hose onto the fitting on the bottom of the radiator. Slide the hose clamp over the fitting and tighten with a Phillips head screwdriver.
    • 5 Slide the upper radiator hose onto the fitting on the top of the radiator. Slide the hose clamp over the fitting and tighten with a Phillips head screwdriver.
    • 6 Fill the engine with a 50/50 mix of antifreeze and water.
    • 7 Run the engine and visually inspect for leaks.

Aug 30, 2011 | 1999 Jeep Cherokee 4WD

1 Answer

Installing radiator


REMOVAL
1. DRAIN ENGINE COOLANT
2. w/ CRUISE CONTROL SYSTEM:
REMOVE CRUISE CONTROL ACTUATOR COVER
3. DISCONNECT ECT SWITCH CONNECTOR FROM FAN SHROUD
4. DISCONNECT ELECTRIC COOLING FAN CONNECTORS
5. REMOVE RADIATOR HOSES
(a) Disconnect the upper hose from the radiator side.
(b) Disconnect the lower hose from the water inlet pipe.
6. DISCONNECT RADIATOR RESERVOIR HOSE
7. A/T:
DISCONNECT OIL COOLER HOSES
8. REMOVE RADIATOR AND ELECTRIC COOLING FANS
(a) Remove the 2 bolts and 2 upper supports.
(b) Lift out the radiator.
(c) Remove the 2 lower radiator supports.
9. REMOVE RADIATOR LOWER HOSE
10. A/T:
REMOVE A/T OIL COOLER HOSES
11. REMOVE ECT SWITCH WIRE
12. REMOVE ELECTRIC COOLING FANS Assembly is reverse order.

Jan 01, 2011 | 1996 Toyota Camry

1 Answer

How do I remove my car radiator?


Section 303-03: Cooling, Engine 1997 Explorer, Mountaineer Workshop Manual REMOVAL AND INSTALLATION Radiator - 4.0L Removal
  1. NOTE: Refer to following illustrations.
    Drain the cooling system by removing the radiator cap (8100) and attaching a 9.5 mm (3/8 inch) inside diameter hose to the draincock nipple, located at the lower rear corner of the radiator tank. Then, open the radiator draincock (8115) and allow the coolant to flow through the hose into a suitable container.
  1. Loosen hose clamps at throttle body and engine air cleaner assembly. Remove air cleaner outlet tube and position aside.
  1. Remove radiator overflow hose from the radiator, disconnect two hose locators at top of radiator and position hose aside.
  1. Remove two fans shroud bolts. Lift the fan shroud out of the lower retaining clips and position it on the fan blade.
  1. Position upper and lower radiator hose clamps, remove hose from radiator and position it on the fan blade.
  1. Disconnect the two transmission cooling lines from the oil cooler fittings on the radiator, install protective caps over lines and position aside.
  1. Remove two upper radiator bolts.
  1. Tilt the radiator back (rearward) approximately 25 mm (one inch) and lift directly upward, clear of the radiator support bracket and the fan blade.
Installation
  1. Position the radiator into engine compartments, make sure that mountings on both tanks are inserted into radiator support brackets. Install radiator retaining bolts. Tighten to 6-8 - (54-70 lb-in).
  1. Remove protective caps from cooler lines. Connect the two transmission cooling lines at the oil cooler fittings on radiator. Tighten to 16-24 - (12-17 lb-ft).
  1. Install upper radiator hose and position hose clamp. Tighten to 3 - (26 lb-in).
  1. Install lower radiator hose and position hose clamp. Tighten to 3 - (26 lb-in).
  1. Position fan shroud in lower retaining clips and install upper bolts. Torque to 6-8 - (54-70 lb-in).
  1. Position radiator overflow hose, connect to radiator and locators.
  1. Position air cleaner outlet tube to throttle body and air cleaner assembly. Tighten to 2-3 - (18-27 lb-in).
  1. Fill the cooling system; refer to Cooling System Draining, Filling and Bleeding in this section.

Oct 28, 2010 | 1997 Mercury Mountaineer

2 Answers

Radiator is leaking, on the drivers side of car. 2002 Chevy Avalanche, 4 wheel drive trcuk. One owner, 106000 miles on it.


Removal & Installation To Remove:
WARNING
To avoid being burned, do not remove the radiator cap or surge tank cap while the engine is on or is still hot. The cooling system will release scalding fluid and steam under pressure if radiator cap or surge tank cap is removed while the engine and radiator are still hot.
CAUTION
If the vehicle's coolant is low, drained out, or has repeatedly needed coolant or water added to the system, then the system should be completely flushed.
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Inlet hose from the radiator
    • Radiator outlet hose from the radiator
    • Lower fan shroud
    • Surge tank hose
    • Vent inlet hose from the radiator
    • Surge tank hose
    • Engine oil cooler lines from the radiator
    • Transmission oil cooler lines from the radiator Remove the radiator chevy_sub25_02-04_rad_rem.gif

    • Radiator bolts
    • Radiator from the vehicle
To Install:
  1. Install or connect the following:
    • Radiator to the vehicle
    • Radiator bolts and tighten the bolts, Torque to: 18 ft-lbs (25 Nm)
    • Engine oil cooler lines to the radiator
    • Transmission oil cooler lines to the radiator
    • Radiator vent inlet hose to the radiator
    • Lower fan shroud
    • Outlet hose to the radiator
    • Inlet hose to the radiator
  2. Fill the cooling system.
  3. Test drive the vehicle to confirm the repairs.
prev.gif next.gif

Jul 21, 2010 | 2002 Chevrolet Avalanche

2 Answers

How do i change the radiator hose?


BUY YOUR RADIATOR HOSES FIRST MAKE SURE NEW HOSES MATCH THE OLD HOSES. BUY NEW RADIATOR CLAMPS AND HAVE EXTRA GALLON OF ANTIFREEZE. MAKE SURE ENGINE IS COOL IF YOU GOING TO CHANGE TOP RADIATOR HOSE REMOVE RADIATOR CAP OR OVER FLOW JUG CAP IF YOUR RADIATOR DONT HAVE RADIATOR CAP FIND RADIATOR DRAIN PLUG.PLACE A CATCH PAN.OPEN RADIATOR DRAIN PLUG CATCH ANTIFREEZE. DRAIN HALF ANTIFEEZE IF YOU GOING TO REPLACE TOP HOSE AND DRAIN OUT ALL ANTIFREEZE IF YOU GOING TO CHANGE LOWER COOLANT HOSE TO WATER PUMP.WHEN DONE CLOSE DRAIN PLUG.PUT ANTIFREEZE IN A SAFE PLACE FROM PETS AND KIDS UNTIL JOB DONE. WHEN YOU REMOVE COOLANT REMOVE WATER HOSE CLAMPS THEN REMOVE RADIATOR HOSES PUT NEW RADIATOR HOSES AND CLAMPS ON HOSES TIGHTEN HOSE CLAMPS DONT OVER TIGHTEN. POUR ANTIFREEZE IN RADIATOR.CRANK ENGINE UP CHECK FOR LEAKS.CHECK COOLANT LEVEL WHEN THERMOSTAT OPENS ADD MORE COOLANT AS NEEDED.

Jun 13, 2010 | 1991 Buick LeSabre

2 Answers

Leaking radiator fluid where lower hose connects w/core


Hi:

If you have a leak near the lower radiator connection that just started, it is either a failed hose, or possibly a radiator core leak that is dripping down to that area.
If you havent changed your radiator hoses for awhile, and they feel soft, it isn't a bad idea to change them both. If you drain your radiator to change the hoses, this would be a good time to inspect the radiator, and perhaps you will find the source of the leak.

Jan 31, 2010 | 1994 Jeep Grand Cherokee

1 Answer

How to replace the radiator fluid


- Make sure the engine is cold and not running.
- Drain the radiator fluid by opening the drain plug at the bottom of the radiator or for a better/faster drainage and cleaning, carefully remove the bottom radiator hose by first loosening the hose clamp.
- Open the radiator cap and water rinse/flush the radiator core via a garden water hose until you no longer see any dirty water coming out of the bottom hose (or drain plug).
- Flush the radiator over flow (plastic) container by overfilling it with your garden water hose.
- remove garden water hose, carefully refit the bottom radiator hose, tighten the bottom radaitior hose clamp, refit/tighten the radiator drain plug.
- refill the radiator with approved radiator fluid for your climate and also refill the radiator overfow tank to the indicated level..
- Refit radiator cap
- Start your engine until it warms up and check for any water or steam leaks. Refit and or replace any faulty hoses or radiator (regulator) cap!
It is not difficult and have fun!

Dec 25, 2009 | 2003 Volkswagen Beetle TDI

Not finding what you are looking for?
2004 Volkswagen Touareg Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...