Question about 1999 BMW 318 ti

Open Question

How to change the heater coreof bmw318 is 97

Replace the plastic tube of the heater core

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Truck doesn't heat while idling


Could be low on antifreeze. The heater core is the highest spot in the cooling system and it may develop an air pocket. Another possibility is the thermostat is stuck partially open and doesn't let the engine warm correctly, watch your temp gauge on the dash and see if it comes up to the middle like it should while idling. If it doesn't, it may need replacement.

Oct 19, 2014 | 2001 Dodge Ram 1500 Truck 2WD

Tip

How To Replace A Heater Core 1995 Olds Aurora


Start inside the vehicle on the drivers side, remove the drivers side bottom dashboard plastic panels, you'll need to pop out the switches on either side of the steering column to access the 10mm bolts that hold the plastic panel, and steel panel under it. Working directly in front of the console above the floor, by the firewall, will be a black plastic cover on top of another black plastic cover. They are held in by 5.5 mm screws. Once both panels are removed, you will finally see the heater core. There are 2 straps that hold the heater core in place. Remove the 5.5 mm screws that hold the straps to the housing. Now, from under the hood, around the center of the firewall, there will be a rectanglar shaped vacuum box mounted on top of a relay bracket, remove to 3 10mm nuts to move vacuum box and relay bracket out of the way to access the heater core hoses. It may help to, from the inside, push the heater core forward thru the firewall, and then from under the hood, cut the aluminum tubes a inch or so from the heater hoses, a long sharp edge flat blade screwdriver might help. You can do this from inside the car, but watch for anti freeze. Remove the hog ring clamps, vice grips might help, in removing them. Use alot of WD-40, by spraying between the hose and the tubing, use a thin screwdriver between the hose and tubing to break the seal of the rubber hose to the tubing. Remove the 2 tubing pieces from the heater hoses. You are ready to reassemble. I'd replace the clamps with some worm gear clamps, alot easier to deal with.

on Mar 07, 2010 | Oldsmobile Aurora Cars & Trucks

2 Answers

2003 mercury sable blows cool air when heater is turned on.


Most likely it is a clogged heater core. Have your heater core reverse flushed or your blend door is stuck open.

Oct 10, 2014 | 2003 Mercury Sable

2 Answers

2002 Mercury Sable - Had intermediate heat- now no heat


backwash your heater core. there are two heater hoses usually 3/4 inch i.d. find out witch one is the return and disconnect both. then take a hose and pressurize the return to flush out core. good luck

Jan 22, 2012 | 2002 Mercury Sable

1 Answer

I need to replace my heater core


The heater core is located above the gas pedal on the drivers side. You have to remove the gas pedal assembly first. Next there is a plastic cover over the heater core tubes held with a screw. Finally release the clamp holding the two aluminum in/out tubes to the core. Push the tubes slightly forward and out of the way. With a little effore it will slide out and the replacement can slide back in.


Hope this helps, James Booth

May 17, 2011 | 1996 Chrysler Town & Country

2 Answers

I have a 2000 Mercury Sable. I put a new water pump on. I'm having trouble getting the heater to work. I've flushed the heater cord both ways. I turn the heater off and let the motor run, then turn the...


have the servo motors in the air control box check and vac.. lines, if it digital controls check conections on the back of controler. good luck!

Jan 12, 2010 | 2000 Mercury Sable

1 Answer

Change heater core in 1999 madza truck? need to know how?


INSTRUCTIONS TO REPLACE HEATER CORE:
(1)Disarm the airbag system;
(2)allow the cooling system to completely cool down;
(3)using a thick cloth for protection, turn the radiator filler cap to the first stop;
(4)step back and let the pressure release;
(5)once the pressure has been released, completely drain the cooling system;
(6) working within the engine compartment, loosen the ****,ps on the heater hoses at the engine compartment side of the firewall, twist the hoses and carefully sepseparate them from the heater core tubes;
(7)plug or cap the heater core tubes to prevent coolant from spilling into the passenger compartment when the heater core is removed;
(8)place a plastic sheet on the floor of the vehicle to prevent stains if the coolant spills;
(9)remove the instrument panel;
(10)remove the PCM heat sink and ground strap;
(11)remove the heater plenum chamber;
(12)separate the heater core from the heater plenum chamber; (13)installation is the reverse of the removal with the following additions; (a)fill the cooling system; (b)run the engine, check for leaks and test the heater.

Nov 13, 2009 | 1999 Mazda Pickup

2 Answers

My heater on my 2001 mercury sable isn't working.. It will blow warm air for about 2 minutes and then goes cold again


I had the same problem with my sable. You need a heater blend door. The one on your car is stuck and wore out. The replacement part costs about fifty-two dollars, labor will be more like about one hundred dollars if you take it to a dealership.good Luck

Dec 16, 2008 | 2001 Mercury Sable

3 Answers

No heat/99 mercury sable


its not a fuse if the blower motor works , you have a clogged or bad thermastat, bad water pump or your radiator heater core is clogged

Nov 25, 2008 | 1999 Mercury Sable

Not finding what you are looking for?
1999 BMW 318 ti Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...