Question about 2007 Kia K2700 Workhorse

Open Question

Timing marks on gears

Cant find settings on timing gears or marks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you adjust valves on a 2006 3.5L V6 Toyota Avalon?


There is a Toyota Technical Service Bulletin issued for this:-
T-SB-0291-08 September 11, 2008 2GR-FE Valve Timing

Procedure Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 Avalon 2007 - 2009 Camry VDS(s): BK46K 2008 - 2009 Highlander 2006 - 2009 RAV4 Engine(s): 2GR VDS(s): BK31V, BK32V, BK33V, BK34V, ZK31V, ZK32V, ZK33V, ZK34V, ZK35V 2007 - 2009 Sienna Introduction This service bulletin provides information regarding valve timing inspection and service guidelines for vehicles equipped with 2GR-FE engines. © 2008 Toyota Motor Sales, USA Page 1 of 5 T-SB-0291-08 September 11, 2008 Page 2 of 5 2GR-FE Valve Timing Procedure Introduction (Continued) Figure 1. 3 2 1 5 9 8 7 6 4 1 RH Bank Intake Camshaft Timing Gear 2 RH Bank Exhaust Camshaft Timing Gear 3 RH Bank No. 2 Timing Chain 4 Crankshaft 5 Idler Gear 6 Timing Chain 7 LH Bank No. 2 Timing Chain 8 LH Bank Exhaust Camshaft Timing Gear 9 LH Bank Intake Camshaft Timing Gear Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 3 of 5 2GR-FE Valve Timing Procedure Inspection 1. Set the No. 1 cylinder to TDC/compression. A. Set the timing mark to 0 on the timing chain cover by rotating the crankshaft clockwise. B. Verify the timing marks on the camshaft timing gears are in general alignment with the timing marks of the camshaft bearing cap: TIMING MARK IDENTIFICATION CYLINDER BANK INTAKE GEAR MARK EXHAUST GEAR MARK RH Bank (Bank 1) Small Mark Single Line LH Bank (Bank 2) Large Mark Double Line HINT When the engine is correctly timed, the timing marks will NOT perfectly align. Figure 2. Figure 3. RH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 4. RH Bank Intake Camshaft Timing Gear 2 1 1 Bearing Cap Timing Mark 2 Gear Timing Mark © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 4 of 5 2GR-FE Valve Timing Procedure Inspection (Continued) Figure 5. LH Bank Intake Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 6. LH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark HINT If the timing marks appear vastly out of alignment, turn the crankshaft one revolution (360 ) clockwise and note the position of the timing marks. Component Removal Guidelines 1. If engine disassembly is required that involves removing the camshafts or timing gears, set the #1 cylinder to TDC compression, wipe away any oil, and mark the following items in relation to each other prior to disassembly: • Timing gears • Timing chain • Timing chain No. 2 NOTE This relationship MUST be maintained. The intake gear is timed in relation to the crankshaft via the timing chain; the exhaust gear is timed in relation to the intake gear via the No. 2 timing chain. © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 5 of 5 2GR-FE Valve Timing Procedure Component Removal Guidelines (Continued) 2. If NEW camshaft timing gears or the No. 2 timing chain are being installed, the two yellow links on the No. 2 timing chain can be used to ensure correct relationship between the intake timing gear and the exhaust timing gear. Figure 7. 1 1 Yellow Link A. Align the paint mark on the timing chain with the intake gear timing mark (to ensure the intake gear is correctly timed to the crankshaft). Figure 8. RH Bank and LH Bank 3 3 4 3 3 4 5 4 5 4 1 2 1 RH Bank 2 LH Bank 3 Yellow Link 4 Gear Timing Mark 5 Timing Chain Paint Mark B. Align the two yellow links on the No. 2 timing chain to the timing marks on

May 04, 2015 | 2006 Toyota Avalon XLS

1 Answer

My 2003 freelander crankshaft mark is set as well the cams but piston is not on top dead center on safe mark on sude mark piston is on top but cant turn it gets stuck


I've worked on freelanders loads of times presuming yours is the petrol model when you set the timing up on these when working on them. all pistons are at the halfway mark in the bores this is so no pistons strike the valves when taking the cylinder head off. So the actual mark if you want it set at tdc you need to take off the crankshaft pulley wheel it won't do any harm just four little bolts if I recall when this crankshaft wheel is out of the way you still have the gear there what the cambelt sits round. It is on that gear where the true mark is to set up the timing with no1 piston at tdc. Infact the pulley wheel needs to come off when changing a cambelt make sure the timing marks are set up properly check twice if nessessary then turn engine over one revolution by hand slowly to make sure no internal parts are hitting and timing marks come back together

Feb 07, 2015 | Cars & Trucks

1 Answer

How do i set timing chian marks


The marks are on the crank and cam gears. They either have a mark on the head that coincides with the mark on the cam gear AND you set that AND then bring the crank shaft gear to TDC on the timing marks OR you have both marks on the gears and you line them up with each other using a straight edge through the center of the shafts, then you put the chain on.

Jun 03, 2014 | 1997 Nissan Maxima

1 Answer

When setting the timing marks together distributor always points to #6 not #1 put new timing chain & gears in but cant get it timed right 5.2


Is it possible to turn the distributor shaft 180 degrees and reinstall the dist ?
I am assuming you have spark at the plugs, just not at the right time ?
If the distributor has not been moved, and the rotor points to the wrong wire, you could have put the cam gear in upside down ?

Jul 01, 2012 | Dodge Cars & Trucks

1 Answer

How to aligned timing set mark on isuzu 4hf1 engine?


Bernard , start a new post, ?

what car,?
what year.?
what country.?

google for it , or buy the book on unstated car.

or search here,

http://www.fixya.com/search.aspx?ref=ser&s=isuzu%204hf1&


or

https://duckduckgo.com/?q=isuzu+4hf1+pump+timing+marks&ia=videos


try searching/
much>?
my guess is this is a huge ELF truck?
not a car,
no a light truck?

Nov 05, 2011 | Isuzu Cars & Trucks

1 Answer

Changed cyl head, on 1996 2.2 toyota camry, cant seem to figure out cam timing


there is a hole in the camshaft gear turn the gear until it lines up with a mark in the cylinder head at the top. then line the crankshaft gear mark up with the mark on the block. sometimes the best way to see the camshaft timing mark is with a mirror.

Aug 16, 2011 | 1996 Toyota Camry

1 Answer

I am replacing the timing belt on a 97 sportage DOHC and i cant figure out were to set the marks at


There are marks on the cam gear and the head to line up when the cover is off. And the lower end the marks are on the timing cover.

Nov 15, 2010 | 1997 Kia Sportage

1 Answer

How to set timming belt,cant find mark for crankshaft 3.0L


Timing belt removed, static timing was not set before removing timing belt.

[Set Static Timing:
No.1 piston is brought up to TDC before removing timing belt.

Cam gear has a punchmark on face of gear, and this mark aligns with one single tooth. There is a matching punchmark on the Timing Belt Rear Upper Cover.

Facing the cam gear, the mark is to the upper right. There is an 'egg shape' of the timing belt upper rear cover, in this spot. This punchmark is in that 'egg shape', and is close to a bolt hole. The cam gear mark lines up with the Timing Belt Rear Upper Cover, mark.

The crankshaft gear has a punchmark on the face. It lines up with one single tooth. There is a corresponding punchmark on the lower right side. An alignment mark)

Should be a round punchmark on the face of the crankshaft gear. It lines up with a single tooth. Wipe the gear clean, use a little carb cleaner. (NO flames, or sparks nearby, well ventilated area)

Barring you cannot find the crankshaft mark, find the camshaft alignment marks, make sure they are aligned with the alignment, (Punchmark), on the Timing Upper Rear Cover.

Count the teeth in the timing belt. There should be 133 teeth on the belt.

There is 43 teeth in-between the timing mark of the camshaft, and the timing mark on the crankshaft.

(43 teeth in-between the Right Side Camshaft mark to crankshaft mark, 43 teeth in-between the Left Side Camshaft mark to crankshaft mark)

There should be 40 teeth in-between the two cam gears.




Oct 24, 2009 | 1989 Nissan Pathfinder

2 Answers

Putting a 1987 Ford Ranger in Time


you have to put the #1 piston at tdc, then put the cam in at the mark.

Nov 30, 2008 | 1987 Ford Ranger

Not finding what you are looking for?
2007 Kia K2700 Workhorse Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...