Question about Chevrolet Equinox

1 Answer

Dim headlight one side

2013 Chevy Equinox Right side headlight dim no high beams and left side is fine... Changed bulbs and fuse but still not working....

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 1,253 Answers

Check voltage to lamp assembly. Could be a relay, a bad wire, or a bad connector. Since one headlamp works correctly, the switch assembly probably works. Without a wiring diagram. I can't tell whether the headlights get power directly from the switch or not... Time to buy a manual.

Posted on Apr 01, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: 2002 Chevy Malibu/ bulb

Autobuygide.com list the recall for this problem.

Posted on Sep 21, 2008

  • 334 Answers

SOURCE: dim headlights

did you check your fuese under the hood al so check were your light plug in you may have a broken wire

Posted on Mar 29, 2009

  • 260 Answers

SOURCE: Low Beam

Make sure you have a good switch
bulbs good
relay and or fuse is good

Posted on Apr 11, 2009

  • 2 Answers

SOURCE: Right headlight low beam does

I had the same problem with my 2004 ram, passenger side low-beam wouldn't work after replacement. Online I saw many things from socket replacement to Fcm replacement. What worked was to remove fcm (front control module) and clean appropriate contacts with small nail file . Repair took less than 1 hour and cost 0$, wish I could give credit where I found info.

Posted on Apr 23, 2012

matt_sams
  • 124 Answers

SOURCE: need wiring diagram for headligt on 2003 chevy impala with 3.8 cu engine

Sounds like a short or the relay is going bad to the headlamps. You may be able to google for the diagram but probably will need to get a repair manual from the nearby auto parts store for appx $25.00. I would start by checking continuity with the battery disconnected on that side from the positive wire to a ground. Also start with checking the relay, they are usually generic and you should be able to swap two as long as the numbers match and see if that fixes the issue.

Posted on Jun 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

1 Answer

Driver side low and high beam on but dim. Passenger side low beam normal but high beam on and dim


I would check for the groundwire continuity

Driver side - dim low beams and no hi beam - Subaru Outback ...

www.subaruoutback.org > ... > General > Electrical & Electronics
Oct 11, 2014 - Hi everyone, My drivers side headlights are dim on low, (car has separate bulbs ... When the headlight switch is turned ON, but for low beams, ...

Driver-side Low beam Not Working (electrical issue not bulb ...

www.hummer4x4offroad.com/.../showthread.php?...Driver-side-Low-be...

Mar 12, 2015 - 10 posts - ‎4 authors
The high beam continues to work on both sides...I pulled the Driverside headlamp fuse and then both left and right beams lit up but very dim.

High beams ok, but not low beam - one side only - TDIClub Forums

forums.tdiclub.com > ... > VW MKIV-A4 TDIs (VE and PD)
Jan 23, 2014 - My driver's side lights are working fine - high and low beams. ... But it definitely looks like the big lamp on the driver's side gets brighter when ..... Drivers side headlight is very dim on low beam and goes out when on high beam ...

Dim driver's side headlight (low & high beam) - GrandAmGT.com Forum

www.grandamgt.com > ... > Technical Q&A

Dec 11, 2002 - 6 posts - ‎4 authors

Jan 04, 2016 | Cars & Trucks

1 Answer

I have a 2008 chevy Equinox. When the headlights are on normal, the left one works but the right one doesn't. When I switch the high beams on, the right works but the left doesn't. Any suggestions?


Head lights are a two stage bulb. One filiment for low beam. One filiment for high beam. The low beam filiment is burnt out . a new set of headlight bulbs will fix you up.

Sep 16, 2015 | Cars & Trucks

2 Answers

\1991 geo metro dim headlight pass side


in low beams or high or both?
that is caused by:
1: bad held lamp. old lamps can go dim.
swap left and right, if dim follows bulb, bingo weak bulb or wrong type bulb. buy matching blubs (same brand and P/n)
2: bad wiring to lamp. damaged wires, or connectors to same.
4: bad combo switch. (if low beams)
5: bad fuse or holder, corrosion , to either.
head lamp fuses. there are 2. left and right.
6: hackers, many hackers put in wrong lights. inspect it.

Sep 30, 2013 | 1991 Geo Metro

1 Answer

Low beam on right side of 2006 dodge ram 1500 doesn't work


the high beams work fine and power goes to the only when vehicle is on when it is off no power gets to the low beam side of the right headlight. ????????

Feb 20, 2018 | 2006 Dodge Ram 1500

1 Answer

I have a 2008 f250. one headlight (driverside) low beam is not working. I have checked both fuses 10amp and they are good. The flash to pass works and both lights on bright, right and left come on. the...


I am sure that a 12 Volt bulb means it needs 12 Volts. Since you changed the bulb to the other side, why not check the voltage in the working side and see what it reads?

Sometimes the turnstalk can interfere with the lighting. Try pushing the Hazard switch several times and see if the headlights straighten out. I read that too much goes through the turnstalk and that using the Hazards can derail a contact inside the stalk.

If this does not help, you may need a headlight relay in the powerbox. One contact may be dirty or burned down for the wire it feeds. Unless you have a single wire feeding both low beams to the headlights, I would bet the left and right side come out directly through the relay.

Oct 20, 2010 | Ford F-250 Cars & Trucks

1 Answer

My passenger side low beam headlight is out. the driver side low beam headlight works fine. I replaced the bulb and the headlight still doesn't work. What should I look at next?


Check the fuse. There are seperate fuses for right and left. You dont mention if the high beam works for that side? If it does, the fuse is good. The GREEN wire at the bulb is the ground for the low beam. If that wire has power, then the ground is bad. If the high beam works, the hi'lo beam switch is good, and there is a problem between that headlight and the Engine Compartment Junction Block

Dec 16, 2009 | 2004 Hyundai Santa Fe

2 Answers

1998 ford ranger headlights do not come on when switch is turned


Look under the hood.
There is a large relay which should have some info about lights on it.
I had this exact problem with my dodge ram

Jan 26, 2009 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

534 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80668 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...