Question about 2002 Dodge Durango

1 Answer

Lights in rear dont turn on when u turn lights on brakes and turn signals lighht up but running lights dont

Turn signals work flashers work brakes light up when pushed down. the rear liscense plate light does not work and the running lamps do not light up

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Dodge Master
  • 2,620 Answers

Check for a blown fuse.

Posted on Mar 31, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 255 Answers

SOURCE: My brake light and turn signal on the left don't work.

Hi, you have a bad bulb,....

Posted on Aug 17, 2008

  • 2 Answers

SOURCE: no tail lights,marker lights (FRT. OR REAR), license plate light

i had the same problem with my 2002 Dodge Ram 1500, the front light control module is bad and its about a $250 part.

Posted on Nov 25, 2008

keithheavili
  • 410 Answers

SOURCE: brake lights out; bulb, fuse okay

Sounds like you need to replace your brake light switch.  It is located on your brake pedal and you should be able to pick it up for around $20-$30 at your local parts store.

Posted on May 19, 2009

  • 335 Answers

SOURCE: All lights work on the rear except the three brake lights

Sounds like the brake light switch has a problem. Located above brake pedal and activated with the brake pedal arm. Check for power going in and coming out when you apply the brake.

Posted on May 24, 2009

wracefans24
  • 1985 Answers

SOURCE: 1997 Dodge Ram 2500 brake lights do not work. The

you need to do basics first,
check to see if bulbs are good,then verify no voltage at bulbs,
check to see if your truck has has a tailor hitch and wiring installed.
where they connect to your original wire is where you need to check first,

Posted on Nov 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Left bleaker and break light not working. Turn signal works bleaks faster than right side.


Has the vehicle been in an accident on the left rear side. First check the bulb to be sure it is not defective, trade it out with the side that works properly to test. If the bulb works well then My thought are you may have a shorted wire. The turn signal flasher works by heat build up within the flasher the heat is caused by the load of the bulbs, the load heats the metal spring causing it to open the circuit then as quickly as it cools down the circuit closes again lighting the bulbs.
There is also a possibility of a defect in the turn signal mechanism on the steering column. The turn signal switch on many models does three different things on many models that use the same bulb element / or bulb for brake and turn on rear of vehicle. It controls the circuit for brake light by sending power both left and right side rear when turn signal is in neutral position then when turn signal is in left turn the switch cancels brake light power to left side rear and supplies flasher power to left side while maintaining brake light supply to the right side rear, and so on opposite when the right turn is chosen on turn signal switch. The turn signal indicators on the dash normally run off the same circuit as front turn signal bulb only which is also controlled by turn signal switch. Front has turn signals but no brake light.
I think there is an additional load on the left side rear turn circuit and it could be either a wire that is shorted or the turn signal switch if the same bulb element is used for both functions.
Often times if trailer lighting is connected the flasher will also blink a little faster because of the extra load of additional bulbs.

Feb 15, 2015 | Cars & Trucks

2 Answers

What would cause the turn signals to work sometimes and sometimes not ?


A bad flasher relay would do that. They are usually located on the fuse panel and plug into it.

Jun 27, 2014 | 1992 Ford Tempo

3 Answers

No brake lights 3rd brake light works just put all new bulbs in.checked all fuses even under the hood,does this vehicle have a flasher fuses because those dont work either. both turn signal and rear lamps...


car should have an emergency flasher. If it isn't working, it could affect the brake lights. might be the same unit as the turn flasher but different relay inside. Is your fuse panel behind the glovebox? manual says flasher is in the fusebox. It's worth a try replacing this flasher unit. Looks like this:

ab6de9f.jpg

Sep 04, 2010 | 2000 GMC Jimmy

2 Answers

Rear turn signals and brake lights out. Front signals and rear tail lights work fine.


the brake lights and the rear turn signals should be the same bulb check the bulbs to make sure they are not blown does your third brake light work if all brake light are out and the bulbs are good check the brake light switch on the brake pedal

Nov 04, 2009 | 1986 GMC C1500

2 Answers

1998 lincoln TC brake light won't work


try replacing signal flasher.good luck.

Sep 30, 2009 | 1998 Lincoln Town Car

3 Answers

Brake light problems on a 2000 chevy lumina


Will your Center High-Mount Stop Light (CHMSL) illuminate when you depress the brake pedal, but the lower/outer lights will not?
-- Do you have to hold the signal lever in a certain spot to get the turn signals to flash?
-- Do you have to hold the signal lever in a certain spot to get the lower/outer brake lights to illuminate?
-- Will the signals work in one direction, but not the other?
If you answered yes to any of the preceeding questions, your turn signal switch is likely malfunctioning.

**One more question before we continue: Is the turn signal lever not "cancelling" (returning to the "off" position) after you make a turn? If this is the case, you have a broken "cancelling spring."


Before you begin disassembly of your steering column, verify the turn signal flasher is not malfunctioning. If your brake lights work fine, but not the signals (either direction,) then it's likely the flasher is burnt out. The flasher itself is located underneath the dash near where the steering column passes through the firewall

Mar 19, 2009 | 2000 Chevrolet Lumina

1 Answer

Left rear turn signal and brake light dont work


You have a broken wire to the turn/brake light portion of the light as they use the same wire. Or where the plug goes into the light assy could be bad. Torsion mount lights are horrible and you should think about replacing with a universal light that you can wire direct.

Feb 17, 2009 | 1997 Jeep Wrangler

Not finding what you are looking for?
2002 Dodge Durango Logo

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...