Question about Nissan Almera

Open Question

Nissan almera washer/wiper switch wiring plug connection.

I have a 2004 Nissan almera 5 door hatch back, the wiring loom connecter harness that connects to the Wiper washer stalk. to The connector i am referring to the is on the multifunctional stalk (windscreen wiper side) on the dash which incorporates the front and rear washer and wipers controls, (near the ignition/starter). the wires have become messed up can you tell me the order the wires goes back in the connecter There are ten (10) wires.:- 1 Orange (thick type) 1 Green /Black (thick type) 1 Green/Red (thick type) 2 Black (thinner type) 1 Pink (thinner Type)) 1 Light Blue (thinner type) 1 Blue/yellow (thinner type) 1 Blue may have a slight hint of yellow (thinner type) 1 Green (thinner Set type) These are the wires going into the harness plug connecter that have become upset

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Hightower971
  • 183 Answers

SOURCE: Wiper/Washer Motor

You may have bought a constant wiper motor, rather than one with intermittent settings. It happens.

Posted on Apr 23, 2009

Ad

SOURCE: driver side wiper won't work, but passenger does

I believe this is a press fit connection. As Knight 007 writes, "it's worn out".

Posted on May 06, 2009

  • 1 Answer

SOURCE: Wiring for Bosch Hologen Fog Lights? Wiring

Look on the relay for the terminal numbers.
Terminal 30 goes to the battery positive.Red Wire
The two terminal 87 go to the fog lights.Black Wires
Match the color wire with what you have on the relay connection for the rest of the wires.
Terminal 86 should connect to your low beam headlight.
Terminal 85 should go to the fog light switch.
The fog light switch should connect to the terminal 85 and the other terminal on the switch will connect to ground.

Posted on Feb 04, 2010

  • 1340 Answers

SOURCE: My 2002 Hyundai Accent GS

I may be able to figure it out but with the haynes not showing the codes which they will usually show the options for all models,I am not sure but will try.If you have a more basic model,not "loaded",the gray/black wire could be for a more loaded model which has a motor driven hatchback so I would like to know if yours is or not.Manufacturers commonly make a 'universal' wire harness,but depending on the model may not use it.You may have also seen it in fuse boxes where there are empty slots because the system they are for is not on your car.
The green orange may be the return for the first wire.If there is any way you could send me a picture of the diagram it would be helpful.There are a couple ways to do it without taking out the page.If you have a digital camera,take somewhat close-up pictures,at least so I can read the letters,maybe 4 or 6 sections,or just the particular section you are referring to.You can use a cell phone,it will be a little tougher,but you can TEXT the images to my email.Either way it is gmccarthy 86 hotmail com.If you are in the USA and want to chat,let me know and I'll send you my # as I do not have free long distance,hopefully you do.Good luck! Greg I'll be here all night EST.

Posted on Sep 29, 2010

  • 52 Answers

SOURCE: replacing starter on 93 pathfinder.have main wire

i believe it goes to the alternator

Posted on Jul 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the wiring harness for a 1995 jeep grand cheeokee


wiring harness is used to connect all the electronic devices in the vehicle from front bumper through to the back bumper
three sections
front engine bay loom
interior looms
rear vehicle loom
wiring loom covers
lighting
motors
communication and monitors
starting and charging
switches and levers
door locks
engine management and transmission computers

26313092-l1c4a4q5iaygyp55rgdzzhpc-3-0.jpg

Oct 16, 2016 | 1995 Jeep Grand Cherokee

1 Answer

2006. Wires disconnected from underhood fuse box panel. How do I determine which wire connects where?


Not quite sure what you mean, did you break a wire harness loom that keeps all the wires bundled together or did you break an actual plug connector?
If you broke a loom clip them use black electrical tape to wrap the wires back together. If you broke a plug, go to the dealer and buy the new plug or harness. the new plug will have mew wires already attached and all you'll have to do is match color, cut, splice, solder, heat shrink and plug back in.
If you have another problem for some reason or another that I haven't hit on then I'd suggest going to your local parts stor or dealership and buy the repair manual for your car, turn to the electricl schematic section and follow your color codes from there..
Good Luck

Jul 13, 2015 | Nissan Quest Cars & Trucks

1 Answer

How do i replace a rear hatch door wiring harness on rover 25


Drop headlong and remove inner tailgate trim.
Find plug connectors and washer connector under headliner and disconnect.
I would then , having disconnected the tail gate fittings from the loom, attach a piece of welding wire between old loom and new. Pull through slowly and carefully.
Reconnect and test before refitting trim panels and headliner

Dec 27, 2014 | Rover Cars & Trucks

1 Answer

Fuse number for winderwiper


Hi Maddie, I'm glad to help! Below, I have posted a diagnostic procedure to see why the wipers are not working on your Dakota. Hope this helps and have an awesome day Maddie!



DIAGNOSIS
WIPER MOTOR

The following are wiper motor system problems,
tests to be performed to locate the faulty part, and
the proper action to be taken. If the malfunction involves
only the delay mode, switch, or wiring, see the
diagnosis for Intermittent Wipe Module and Wiper/
Washer Switch.
CONDITION
Motor will not run in any wiper/washer
switch position.
PROCEDURE

(1) Check fuse 10 in the fuseblock module. If OK,
go to step 3. If not OK, replace fuse and go to next
step.
(2) Check motor operation in all wiper/washer
switch positions. If not OK and fuse blows, go to step
5. If not OK and fuse is OK, go to next step.
(3) Place wiper/washer switch in LOW position and
listen to motor. If you cannot hear it running, go to
next step. If motor is running, check motor output
shaft. If output shaft is not turning, replace motor
assembly. If it is turning, drive link to output shaft
or linkage is not properly connected. Replace worn
parts and/or properly connect drive link to the motor
output shaft.
(4) Connect a voltmeter between motor terminal L
and ground strap (Fig. 1). If there is little or no voltage
(less than 1 volt), move negative test lead from
the ground strap to battery negative terminal. If an
increase in voltage is noticed, the problem is a bad
ground circuit. Make sure the motor mounting is free
of paint and that mounting fasteners are tight. If
there is still no indication of voltage, the problem is
an open in wiring or faulty wiper/washer switch. If a
small increase (greater than 3 volts) in voltage is observed,
the problem is a faulty motor assembly.
(5) Disconnect motor wiring connector and replace
fuse. If fuse does not blow, motor is defective. If fuse
blows, wiper/washer switch or wiring is at fault.
CONDITION
Motor runs slowly at all speeds.
PROCEDURE

(1) Disconnect wiring harness connector at motor.
Remove wiper arms and blades. Connect an ammeter
between battery and terminal L on motor (Fig. 2). If
motor runs and average ammeter reading is more
than 6 amps, continue to next step. If motor runs
and average ammeter reading is less than 6 amps, go
to step 3.
(2) Check wiper linkage or pivots for binding or obstruction.
Disconnect drive link from motor. If motor
now runs and draws less than 3 amps, repair linkage
system. If motor continues to draw more than 3
amps, replace motor assembly.
(3) Check motor wiring harness for short between
high and low speed circuits. Connect a voltmeter or
test lamp to motor ground strap. Set wiper/washer
switch to LOW position. Connect other lead of voltmeter
(test lamp) to terminal H of the wiring harness.
If voltage is present, there is a short in the
wiring or wiper/washer switch. If no voltage is
present, go to next step.
(4) Set wiper/washer switch to HIGH position.
Move voltmeter (test lamp) lead from terminal H to
terminal L of the wiring harness. If voltage is
present, there is a short in the wiring or wiper/
washer switch.
CONDITION
Motor will run at high speed, but not at low
speed.
Fig. 1 Voltmeter Between Terminal L and Ground

Motor will run at low speed, but not at high speed.
Fig. 2 Ammeter Between Terminal L and Battery
WIPER AND WASHER SYSTEMS 8K - 3

Apr 26, 2014 | 1995 Dodge Dakota

1 Answer

Which fuse is for the headlights in a 2004 toyota prado?


Hello
Check the connection between the stalk and the vehicle wiring loom.
This is on the underside of the steering column and you will have to remove a bit of trim to get to it.
What happens is the earth wire connection between the stalk and the loom fails. It gets hot and burns really. You will see a dark mark through the centre of the multiplug. This is the burnt connector. It is a black wire from memory.
I usually just bridge around it with a length of wire.
The alternative position for the relay is in the drivers footwell behind the right kick panel.

Aug 20, 2013 | Toyota Land Cruiser Cars & Trucks

1 Answer

Back hatch on 2004 chevy trailblazer will not open...


You could have a bad Lift Gate Module (LGM) or a broken wire in the wire harness going thru the rubber boot between the body and the lift gate.
But first check fuse #19 in the rear fuse panel.

Mar 06, 2013 | 2004 Chevrolet TrailBlazer

2 Answers

How do you repair a back windshield wiper on a 2004 GMC Envoy? It does not function when turned on.


listen to tell if the motor is turning. some times the fastener comes loose on the arm and can be tightened, but you must first get the motor in the rest position. if the motor is not working, check the appropriate fuse. if ok, you'll need to remove the panel on the inside of the hatch. this should give you access to the motor. unplug, and test for power and ground with key on and engine off. operate the switch while checking with a 12 volt test light. connect test light to ground to check for power, and to power to check for ground. if ok try tapping on motor. sometimes this will make it work, but only on a temporary basis. motor replacement will be obvios when you see how it' smounted under the panel.

Dec 21, 2010 | 2003 GMC Envoy

2 Answers

My rear hatch want open from the outside nor will the glass open. I had it checked and they said it wasn't getting power to the door but didn't know what the problem was.


I had the same trouble and found that I had to disconnect the glass hatch switch. It is probably defective like mine. I had to release the door by going from the inside and opening a little plastic door and open the whole hatch by using the emergency lever. Then I had to unscrew the plastic panel near the glass hatch and pry it apart just enough to disconnect the glass hatch switch. It is just a small connector that pulls apart. There are two connectors. One for the back wiper and then the glass hatch so make sure you disconnect the right one. This allows me to use the whole door but the glass hatch becomes useless unless you get a new switch.

Jul 05, 2010 | 2004 Mitsubishi Endeavor

1 Answer

How do you remove the wire connection for the turn signal/ wiper control arm1997 gmc jimmy


if you check/follow the wire loom from the switch/stalk it will route underneath lower dash alongside steer column then normally it has a plug which plugs into main loom when you req this switch/stalk as new it comes complete with its short wire loom fitted ready to fit/plug in

Apr 25, 2010 | 1997 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...