Question about Dodge Grand Caravan

Open Question

Back door is lock

The lock stays in one positions and I can;t open or unlock the door

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 8 Answers

SOURCE: child door locks

latched needs replacing

Posted on Jul 08, 2008

Ad
  • 1 Answer

SOURCE: 2005 Toyota Sienna Sliding Door Won't Open

Have 2005 Sienna and its Driver side door was not openning. Cheap dealer fixed it himself in front of me. After opening the doors plastic assembly while sitting inside with a screw driver. Then he bent the clip towards left where the metal wire is connected. If you guys want to see what he did i would record a video and upload for you guys. Let me know at xahid2000@yahoo.com

Posted on Mar 13, 2009

  • 1 Answer

SOURCE: door lock on 2005 -3500 truck

Yes Admin,
This is what I found out. The problem was with the power lock portion of the part (siezed). It is also sealed and unserviceable. The good news is that the part was in stock at the dealer for around 65.00. Actually pretty amazing considering how many parts there are to the device. After disassembling the door three times (once to diagnose, once to take apart and disable the power lock function, and one last time to swap out mechanism) I became fairly quick at it. If you have this problem, just go buy the part and don't mess around. Oh yeah-you'll need a torx bit to get started.....

Posted on Mar 25, 2009

cadman000
  • 607 Answers

SOURCE: 1998 chevy silverado door latch will not open

sounds like the linkage is disconnected from the latch unit. Becessary to remove the door trim to inspect and repaiir. Hope this helps

Posted on May 01, 2009

  • 1810 Answers

SOURCE: 1995 Chev Suburban rear door latch stuck in locked position

sounds like you lached the door
use a screw driver or some such tool
lift the outer handle and slip your tool in the middle of the lock hole in the door flip the lach open wile holding handle up

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sliding door will not auto close


I unlocked all doors, trans in park and it seemed to stay shut.

Mar 30, 2014 | 2006 Toyota Sienna

1 Answer

Doors will not stay unlocked


power relay fused in lock position.. replace relay.

Jan 03, 2014 | 2008 Ford Fusion

1 Answer

Mazda 6 2005 driver door jammed


if you talking about door latch wont let door close.try to reset all door locks.first if you cant get door close.work unlock button with remote or door switch.then hold open door handle while you flat screw driver pull up latch in door latch should stay up so door will close.once get door close.try resetting all door locks by sitting inside vechicle with all doors close.remove key from ignition.open drivers door.wait 24 seconds.turn ignition switch on and back to lock position 3 times.press and release drivers door courtesy light 3 times.ensure doors lock and unlock.if not wait 40 seconds and repeat procedure.if this procedure fails. you have problem in the door latch and lock mechanism inside the door itself.

Jan 04, 2013 | 2004 Mazda 6 Sport

1 Answer

How to program my new control remote to my Honda passport 2000


Try this please!
'98 - '02 Isuzu Rodeo and Trooper and Honda Passport(with factory keyless entry) Instructions for programming. 1. Get in car and make sure all doors are unlocked. 2. Open driver's door and leave open. 3. Put key in ignition. 4. Turn key to 'on position' (dash lights on, but do not start) and back to 'off position' 3 times in 5 seconds or less. (you must turn the key very fast) 5. Close and open driver's door 2 times in 5 seconds or less. 6. Turn key to 'on position' and back to 'off position' 5 times in 5 seconds or less. (turn key very fast) 7. Close and open driver's door the doors should lock and unlock twice after this happens push the lock or unlock button on the remote, doors will lock and unlock. Push the lock or unlock button a second time and doors will lock and unlock again. You are finished! The above sequence erases all previous codes and adds the new code as #1. If you are adding a second remote, you should follow the same sequence with the exception of step 6; instead of turning the key to the 'on position' and back to the 'off position' 5 times in 5 seconds or less, do it 3 times in 5 seconds or less and then continue to step 7. ***Remember to turn the key to the on and off position very fast. This works! Follow directions EXACTLY. I had to try 3-4 times before getting it to work. I failed to go exactly by the instructions the first few times.

Jan 03, 2013 | Cars & Trucks

1 Answer

My Toyota 2001 rav4 remote light stays on it does nt open the doors alarm does not activate


Hi,
The light for the keyless remote fob stays on? If so the battery may need replaced.

Here is link to a remote - LINK.IF this is yours get a battery @ your grocery store.

-open the key fob w/a flat screwdriver
-note the battery's position - is the '+' or the '-' visible?
-replace the batter the same way
-snap the cover back on

To reprogram (should also be in the Owner's manual):

1. Start with the key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Close the drivers door
D. Insert the key into ignition and leave it in ignition.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically
indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door
locks should lock and then unlock once indicating successful programming. If
the door locks cycle twice, repeat steps A and B in step 6 as the remote was
not accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

Oct 18, 2012 | Cars & Trucks

1 Answer

Passenger door will not open


I can think of two possibilities:

1) The electronic lock is malfunctioning and forcing the door to lock. From the inside of the car, try forcing the lock to the 'unlocked' position. If you can do this with your had, but it 'snaps' back to 'locked' then it's an electrical problem. Possibly the lock solenoid itself, or the BCM.

2) If you cannot force the lock to the 'unlocked' position, then it's some sort of mechanical problem - maybe the lock is just jammed. Try spraying oil into the locking mechanism from the outside and working the lock until it's free. Otherwise, remove the interior door panel and diagnose the mechanical lock.

Feb 01, 2010 | 2003 Hyundai Tiburon

1 Answer

Cant get back door to stay closed . The lock is stuck in locked position I think and the door is open. When I go to close it, it is'nt staying closed. Had to duck tape it to stay closed. LOL! I keep...


It sounds to me ( correct me if I'm wrong ) like the door latch on the side vertical edge of the door is in the LOCKED POSITION. In order to unlock it perform the following. First electrically with the LOCK button UNLOCK the locks. Now with one hand hold the OUTSIDE DOOR HANDLE IN THE OPEN POSITION, while at the same time FLIPPING OPEN THE LATCH. All Done . Now you can close the door. Hope this helps

Jun 27, 2009 | 1997 Chevrolet Lumina

2 Answers

Door locks won't stay locked.


make sure your rear truck latch handle isnt partial returning back to it full replease position and all other handles for that matter. if they stick and dont snap back they will cause some auto locks to lock or unlock. particularly the geo tracker rear latch will lock up on you and it gets rusty from road grime

Dec 08, 2008 | 2007 Saturn VUE FWD 4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...