Question about 1999 Renault Megane

1 Answer

Find supplier of used Exhaust Manifold for 1999 coupe

Having difficulty finding a supplier who knows which Exhaust Manifold is necessary to fit a 1999 (1st March) Renault Megane Coupe. Already been sold the wrong one and now stuck Fred McIlmoyle

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 64 Answers

Had same problem ..use you cars serial vin number and check manufacturing date . as that is where the problem lies...1 month can mean a totally different part required.

Posted on Mar 31, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 13 Answers

SOURCE: Rattling noise - Renauly Megane

are you loseing oil
could be very low on oil
or bottom end going? be may its the sheild just come lose

Posted on May 11, 2009

Rencoupe27
  • 4 Answers

SOURCE: Renault Megane Coupe-Cabriolet juddering problem

Or dont keep your foot on it all the time as this will make it hot, Best is to go into Neut as much as you can to give it a rest from biting all the time

Posted on May 27, 2009

  • 16 Answers

SOURCE: Could you tell me where the Air Temperature Sensor is ?

The Air temperature sensor is located in middle of the front bumper bottom air intake.

This should not to be confused with air mass meter or sensor.

Simply Jack up the front passenger side and have a good look, it`s a black small block with a plug and wires just out of the way of air intake. Should be not to far away from fog light housing but at the back of the bumper not front.

It`s located in this place as to get the best air temp reading but not get wet or be influenced by engine temp. Clever hey!!

Posted on Oct 05, 2009

  • 2 Answers

SOURCE: windscreen washer does not work

i Just fixed a problem with a renault megan washer motor. If the motor makes a noise but is not pumping any water & the jets@ the windscreen are clear, then pull the suqirter motor out off the washer bottle( the bottle stays in place ) it just pulls out from underneith the bottom stone tray& may need to remove bottom bolt, inner lower wheeel arch. Right Now where the black & white squirter come out of the motor gentlywith a screw driver pop these off together. ( test motor again) ( put in water ) Then with Snap ring plires & part the white & black outlets apart & you will find a rubber seal that looks like it must of grown. When it grows it blocks both ports off. you need to shorten the rubber & keep it flat as remember its job seems to block off either the front or rear port. if it not a good finish you may get water coming out of the front & the rear ifeg your working the front squirters

Posted on Jul 11, 2011

soroush92
  • 1 Answer

SOURCE: radio problem, keeps beeping and saying code.

Does anyone have a solution to this? I've had the same problem for a while too. Holding vol+ and vol- doesn't work

Posted on Jul 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vauxhall vxr exhaust manifold torque settings


german specs man gernan specs, u took the old one off so you know how tight they were gooden tite lol

Nov 25, 2013 | Cars & Trucks

1 Answer

I need to find EGR on my 1999 galant


All EGR Valves have an exhaust tube going to them

The output is close to the intake manifold & puts
the exhaust into it.

Should not be hard to see, if you know what one looks like

Why are you finding it?

Don't throw parts at it, because someone said to

Have the valve tested,it has to fail or you don't replace it

Sep 13, 2012 | 1999 Mitsubishi Galant

1 Answer

What is the torque setting for 1999 ford 182 exaust manifold


Check this for 1996-1999 FORD 3.0L (182) V6 DOHC...
- Install the exhaust manifold with a new exhaust manifold gasket.
- Install the exhaust manifold retaining studs and tighten to 13-16 ft. lbs. (18-22 Nm) in the sequence illustrated.
Raise and safely support the vehicle.
Position the Y-pipe assembly using a new flange gasket and install all the retaining nuts and bolts loosely.
Starting at the front of the system tighten the Y-pipe to exhaust manifold nuts to 26-34 ft. lbs. (34-46 Nm).

- Tighten the converter to transaxle nut and bolt to 30 ft. lbs. (40.3 Nm). Tighten the converter outlet bolts to 26-34 ft. lbs. (34-46 Nm).

zjlimited_1988.jpg

Fig. Right side exhaust manifold mounting bolt tightening sequence-3.0L DOHC engine (click image for zoom)


zjlimited_1989.jpg

Fig. Left side exhaust manifold mounting bolt tightening sequence-3.0L DOHC engine (click over image for zoom)

Hope this helps (remember to rating this answer).

Oct 06, 2011 | 1999 Ford Taurus

1 Answer

Where do I find bank 2 sensor 1 on a 1999 cadillac deville


bank 2 sensor 1 is an oxygen sensor located in the exhaust with a wire coming off it.Bank 2 means the front side and sensor 1 means it is in the manifold. So the sensor is in the front exhaust manifold, let me know if this helps you

Jan 19, 2011 | Cadillac DeVille Cars & Trucks

1 Answer

Where are the exhaust system bolts located?


Removal & Installation 2.2L Engine To Remove:
  1. Remove or disconnect the following:
    • Negative battery cable.
    • Heat shield.
    • Oxygen sensor.
  2. Raise and safely support the vehicle.
  3. Remove exhaust pipe from the exhaust manifold.
  4. Lower the vehicle.
  5. Remove the exhaust manifold mounting nuts from the cylinder head. chevy_cav_02-04_exmanifold.gif

  6. Remove the exhaust manifold.
  7. Clean the mating surfaces.
  8. Check for cracks, broken flanges and gasket surface damage.
  9. Use a straight edge and a feeler gauge. If the flanges or the mating surfaces do not align, the manifold is warped and should be replaced.
To Install:
NOTE: The manufacturer recommends using new exhaust system nuts.
  1. Install the manifold gasket.
  2. Position the exhaust manifold to the cylinder head. Exhaust manifold 2.2L 87953055.gif

  3. Install the new exhaust manifold nuts. Tighten the nuts starting from the center and working toward the ends to 110 in lbs (12.5 Nm).
  4. Raise and safely support the vehicle.
  5. Install the exhaust pipe to the manifold using a new flex coupler gasket.
  6. Install new exhaust flange mounting nuts.
    • Tighten to 33 ft lbs (45 Nm).
  7. Lower the vehicle.
  8. Install the oxygen sensor.
  9. Install the heat shield.
  10. Connect the negative battery cable.
2.4L Engine To Remove:
  1. Disconnect the negative battery cable
  2. Disconnect the Oxygen (O2) sensor electrical connector.
  3. Remove the (O2) sensor.
  4. Raise and safely support the vehicle. Exhaust brace 2.4L 87953053.gif

  5. Remove the exhaust manifold brace-to-manifold bolt and the oil pan nuts, if necessary. Exhaust heat shield 2.4L 87953051.gif

  6. Remove the upper heat shield. NOTE: Do NOT bend the exhaust flex decoupler more than necessary to remove it. Excessive movement will damage the flex decoupler
    Exhaust flex decoupler 87953056.gif

  7. Remove the manifold-to-exhaust flex decoupler fasteners.
  8. Remove the exhaust pipe.
  9. Carefully lower the vehicle.
  10. Remove the exhaust manifold-to-cylinder head mounting nuts/bolts. Remove the exhaust manifold.
  11. Discard the gaskets and/or seals. Clean the mating surfaces.
To Install:
Exhaust manifold 2.4L 87953055.gif

  1. Install new exhaust manifold gaskets. Position the exhaust manifold on the cylinder head. Tighten the mounting bolts in sequence to 110 in lbs (12.5 Nm).
  2. Raise and safely support the vehicle.
  3. Install the exhaust manifold heat shield. Tighten the mounting bolts to 10 ft. lbs (14 Nm).
  4. Install the exhaust manifold brace-to-manifold bolt and the oil pan nuts. Tighten the mounting bolts to 41 ft lbs (56 Nm) and the nuts to 18 ft lbs (24 Nm).
  5. Position the exhaust pipe to the manifold. Install the manifold-to-flex decoupler mounting bolts. Tighten to 26 ft lbs (35 Nm).
  6. Lower the vehicle.
  7. Coat the threads with a suitable anti-seize compound and install the O2 sensor.
  8. Connect the O2 sensor electrical connector.
  9. Connect the battery ground cable and check for leaks.
prev.gif next.gif

Sep 02, 2010 | 2000 Oldsmobile Alero

2 Answers

Location of o2 sensors on 1999 chevy express


You will find the 02 sensors on the exhaust manifold. Rather a nightmare to replace!

Mar 26, 2010 | 1999 Chevrolet Express

2 Answers

On a 2001 chrysler sebring coupe lxi 3.0 where is the O2 "oxygen sensor" physically located, computer says bank1 sensor2. I know Bank 1 is the side where the #1 cylinder is which I "think" is on the...


the only sensor that would be on your manifold would be the o2 sensor ihave an intrepid i have four, two converters. 1 before each converter and 1 after each converter. fronts are 1s and backs are 2s all are 4 prong maybe your backs are threes you will need to investigate a little more after all we are dealing with pretty much the same car same year

Jan 11, 2010 | 2001 Chrysler Sebring

2 Answers

Where is the AC Low pressure valve on a 1999 Pontiac Grand Prix?


sometimes its behind the alternator real close to the firewall. Find the bigger of the two hoses and pipes the low side is always bigger. Also the cap is blue and the fitting for the charging can will only fit on the right valve.

Apr 24, 2009 | Pontiac Grand Prix Cars & Trucks

Not finding what you are looking for?
1999 Renault Megane Logo

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

xxxxxx xxx

Level 3 Expert

4860 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...