Question about 2008 Toyota Yaris
Pass side switch work good but when trying to open or close from drivers side no work. changed switch assy already
IT MAY BE THE WIRING ISSUE
Posted on Apr 21, 2014
Which assembly did you change?. It's could be the passenger switch as feed from drivers side not getting being registered. Look for remote connector on assembly and put live feed on it to test. Should isolate problem.
Posted on Mar 31, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Open the rear hatch. Pull off the inner trim panel. Look to see if there is a little box with a bunch of wires connected to it. It may be at the lower edge, driver side. Turn the key on. Test for 12 volts at the solid BLUE wire (there is only 1 solid blue wire) that is connected to the box. Is there power? If not, check the 30 amp POWER fuse. If there IS power, this box may be bad. This is the power window relay for the rear hatch. The wiper/washer and the rear window motor power all come out of this box.
Check for power & get back to me before you buy a relay box, there are a few other tests I could share with you before we pronounce the relay box bad...
Posted on Sep 24, 2008
Your car is still under warenty from toyota.
they will be more then happy to fix this problem for you.
i would know i work there.
Posted on May 29, 2009
i know on some toyotas, you do not need to remove the door panel just the handle where the switch assembly is located...if the panel around the switches is plastic then pry GENTLY up on the plastic to dislodge it from the door handle and inspect connections there...if everything checks out fine, then check fuses...perhaps this was a problem for so long that the window motor finally blew a fuse. if so replace both fuse and motor...if fuses okay, then with a long screw driver locate any screws under the door handle, bottom of the door panel, mirror panel etc, and remove...then gently pry outwards on door panel until it is released. disconnect your harness at the window motor and hook in a test light and operate the switch..if light illuminates, replace motor..if not, then replace switch or switch panel..which ever/.
Posted on Nov 14, 2009
the wire harness that runs from the door to the car from opening and closing the door ive seen the wires break try to move them first while working the switch sometimes it will start to work
Posted on Feb 28, 2010
Testimonial: "That didn't work but I appreciate your time & advice. Thank you"
take the door panel off, or if you can just remove the switch panel. When you can see the back of the switch jump the two ends of the switch and see if the window goes up or down. If not then the motor is shot, if it works then the switch is shot.
Posted on Mar 03, 2010
Tips for a great answer:
Jun 29, 2017 | Cars & Trucks
Aug 14, 2016 | 2007 Mazda 6 2.3
Apr 13, 2016 | 1999 Oldsmobile Aurora
Mar 12, 2015 | Cars & Trucks
Loose wire on switch or dirt in switch you will have to open and clean.
Nov 24, 2010 | 2002 Kia Sportage
Sep 25, 2010 | 1995 Jeep Grand Cherokee
Aug 28, 2010 | 1997 Oldsmobile Cutlass Supreme
Aug 06, 2010 | 1998 Subaru Impreza
Dec 25, 2009 | 1998 Pontiac Trans
Oct 09, 2009 | 2002 Toyota Tundra
41 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: