Question about 2004 Land Rover FreeLander

Open Question

4wd rear wheels have locked after parking

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Rear drums smell like something is burning and are hot.


remove the drum and inspect you job. small shoe on front big shoe on back.brake lube on the backing plate.lose the adjuster and inspect,lube the adjuster, give more free play on your parking brake cable 3 click is the normal before lock the wheel. Inspect the master cylinder for overfeel, remove any fluid over the max level. inspect the fluid for contamination(burn smell or oily)flush the system. lift the Jeep and pump on the brakes,if the wheel is locking open the bleeder screw.if brake fluid is under pressure,replace the hoses.
good luck

Oct 24, 2014 | 1999 Jeep Cherokee 4WD

1 Answer

1990 Astro AWD. AWD quit working overnight while parked!


AWD vehicles have a centre diff in the transfer case and if there is no traction on the rear wheels then the front wheels will not turn. All wheel drive is not equal to 4 wd which you assume apparently. Check that there is not a diff lock button in the car to lock the centre diff turning it into 4wd vehicle in which case the front wheels would have moved the vehicle

Feb 18, 2014 | Cars & Trucks

1 Answer

96 pajero auto no power front right wheel i 4wd trans fluid level ok


wd diff lock only locks the front to rear diffs not the 2 wheels on the same diff. To have both front wheels driving as you require will need limited slip diff in front or locker in front Be hard to steer in tight areas but they are available.

Apr 22, 2013 | Cars & Trucks

1 Answer

2001 Subaru Legacy Lancaster is it 2WD or 4WD?


easiest way to tell if it is 2 wheel or 4 wheel is look under the car. From the front of the vehicle just off center (could be left or right) there will be a differential. (much like what you see under the rear of a pickup truck. If you see this it's a 4wd or awd. The difference between awd and 4wd is- 4wd is either front or rear wheel drive with the ability to (now days) push a button and "lock in" the other axel. Awd is at all times, all 4 wheels are working together to move the vehicle.

Dec 31, 2012 | Subaru Legacy Cars & Trucks

1 Answer

2002 Chevy 4wd


maby im wrong but if you rev up and only rear wheels spin that means that it might be 4 wheel drive but not constant 4 wheel drive or diff lock system ,,,, ,, in 4 wheel drive all wheells will turn together but if pressure of slip is bad enough or torque high enough only 2 wheels will drive ,,, thats why diff lock locks wheels together in each axle to over come this ,,, all wheel drive like in landrover locks all 4 wheels together to ensure all wheels rotate to give best grip

Feb 13, 2012 | 2002 Chevrolet Suburban

4 Answers

What is auto 4 wheel drive?


Auto 4 wd is when the Silverado's PCM takes readings from the front and rear driver shaft and when there is any detection that the speeds are different. The Auto 4WD will activate the transfer case to lock it self to 4wd until the front and rear drive shaft are running at the same given speed of rotation.

Thank you for using fixya

Aug 24, 2010 | 2000 Chevrolet Silverado

1 Answer

When i put my jeep in 4 wheel drive the rear passenger tire locks up like the brake is on. tried driving it hoping it would come out of it , but no luck. you can see tire tread marks where rear wheel was...


weird this because two wheel drive is rear drive only??? wonder if vehicle has a diff lock and something is wrong with this when 4wd is engaged

Dec 07, 2009 | 2002 Jeep Liberty

2 Answers

My 2003 mountaineer when I drive in reverse and turn will come to a stop if I don't really push on the gas. I have had the wheel bearings changed and the rear clutch fluid drained - that did not work -...


it sounds like your 4 wheel drive is engaged. whether on purpose or its stuck thats your problem, to double check jack up one of your front tires, if it wont turn then thats your problem

Nov 05, 2009 | 2003 Mercury Mountaineer

1 Answer

94 landcruiser brakes


Rear DRUM instructions are first If you would Like Pictures and all They Must Be Emailed as TOO LARGE For FixYa's Format im at aol.com
Just use my Knickname@ and let me know where to send.


  1. Raise and support rear of vehicle, then remove wheel and tire assembly.
  2. Remove brake drum. If brake drum cannot be removed easily, insert a suitable screwdriver through hole in backing plate, then push adjuster lever away from adjuster and back of adjustment tension.
  3. Remove tension spring, using a suitable tool, then remove rear shoe hold-down spring and pin. Remove rear brake shoe and anchor spring, Fig. 7.
    1. On Land Cruiser models, remove front hold-down spring using a suitable tool, then disconnect the parking brake cable from the parking brake bellcrank, Fig. 7.
    2. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, remove front shoe hold-down spring and pin, using a suitable tool, then disconnect No. 1 parking brake cable from No. 3 parking brake bellcrank.
    3. On 2WD T100 models, proceed as follows:
      1. Remove E-ring, then automatic adjusting lever and C-washer, then parking brake lever. Disconnect brake line from wheel cylinder using a suitable container to catch fluid.
      2. Remove wheel cylinder. Remove following parts from wheel cylinder: two boots, two pistons, two pistons cups and spring.
    1. On models except 2WD T100, remove front brake with strut, then disconnect parking brake cable from front shoe. Remove parking brake cable No. 2.
    2. Remove adjusting lever spring, then the adjuster from front shoe.
    Inspection
    1. Measure brake drum inside diameter. Inside diameter should be 11.61 inches,
      1. Measure brake shoe lining thickness, Fig. 3. Minimum thickness should be .04 inch on models except on T100 models and .039 inch on T100 models.
      2. Inspect brake lining and drum for proper contact and replace drum or shoes as necessary.
      3. Inspect wheel cylinder for corrosion or damage.
      4. Inspect backing plate for wear or damage.
      5. Inspect bellcrank components for bending, wear or damage.
      6. Apply a suitable lubricant to backing plate contact areas.
      Installation
      1. On 2WD T100 models, proceed as follows:
        1. Apply lithium soap base glycol grease to piston cups, pistons and boots.
        2. Assemble and install wheel cylinder.
        3. Connect brake line to cylinder.
      1. Apply high temperature grease to following parts:
      1. Apply a suitable lubricant to adjuster bolt threads and end.
      2. Assemble adjuster to lever, then install adjuster lever spring.
      3. On Land Cruiser models, install parking brake lever cable to parking brake shoe, then attach cable to bellcrank.
      4. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, install No. 1 parking brake cable to parking brake lever shoe, then attach the other side of cable to No. 3 bellcrank.
      5. Position front shoe in place with end of shoe inserted into piston, then install shoe hold-down spring and pin using a suitable tool.
      6. Assemble anchor spring to front and rear shoe, then install rear shoe with end inserted in piston.
      7. Install rear shoe hold-down spring and pin, then the tension spring.
      8. If necessary, adjust bellcrank as follows:
        1. Lightly pull bellcrank in direction "A", Fig. 8, until there is no slack in part "B".
            1. Rotate adjusting bolt until dimension "C" is .016-.031 inch.
            2. Lock adjusting bolt with locknut, when connect parking brake cable to bellcrank.
            3. Install tension spring.
          1. Ensure proper parking brake travel.
          2. Pull adjusting lever cable upward, then release and ensure adjusting bolt rotates. If bolt does not rotate, check for improper installation of rear brakes.
          3. Adjust strut to shortest possible length, then install drum.
          4. Pull parking brake lever fully upward. Repeat process several times.
            1. Remove drum, then check for proper clearance, Fig. 4. Clearance should be .024 inch. If clearance is not as specified, check parking brake system.
            2. Install brake drum, then bleed and refill brake system.
            3. Install wheel and tire assembly, then lower vehicle.

FRONT ROTORS & PADS
  1. Remove caliper.
  2. Remove cap and snap ring, Fig. 10, then remove cone washers with tapered punch.
  3. Insert suitable length bolts into flange bolt holes, then tighten bolts evenly and remove flanges.
  4. Remove free wheel hub cover and snap ring, then remove nut, spring washer and cone washer with suitable tapered punch.
  5. Remove free wheel hub body and gasket.
  6. Remove locknut, lock washer and adjusting nut.
  7. Remove axle hub and brake disc as an assembly.
  8. Remove oil seal and inner bearing from hub.
  9. Reverse procedure to install. Torque adjusting nut to 43 ft. lbs., then back off nut. Torque nut to 18 ft. lbs. Using spring scale attached to hub bolt, check that preload is 1.4-12.6. Install lockwasher and locknut, if equipped. Torque locknut to 35 ft. lbs., and recheck preload. Secure lockwasher by bending one tab inward and one tab outward.
  1. Raise and support front of vehicle, then remove tire and wheel assembly.
  2. Remove clip and hole pins, Fig. 9.
  3. Remove anti-rattle spring and shim(s) if equipped, then remove brake pads.
  4. Lubricate caliper housing with suitable brake grease at pad contact points.
  5. Reverse procedure to install.

Jan 28, 2009 | 1994 Toyota Land Cruiser

Not finding what you are looking for?
2004 Land Rover FreeLander Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...