Question about 2007 Toyota FJ Cruiser

1 Answer

Location of crankshaft sensor

Need to replace

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 43 Answers

As you face the engine from the front bumper, it is on the lower right side of the engine, below the oil filter and kind of in line with the crankshaft pulley. Should be the only thing in that location with wires going to it. good luck!

Posted on Mar 31, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor located in the 1990 Chevrolet Corsica 4 cylinder 2.2 liter engine?


Follow this link to a diagram that will show you where it's located. Hope this helps.

Jul 11, 2016 | Chevrolet Cars & Trucks

1 Answer

Need to know the location of both crankshaft position sensor on 2008 Chevrolet hhr plz thx


Only has one crankshaft position sensor ,an cam sensors . To change the crank sensor u would have to pull the starter ,located above starter .
Camshaft Position Sensor Replacement - Intake Camshaft Position Sensor Replacement - Exhaust
After a crank sensor replacement a
Crankshaft Position System Variation Learn has to be done !
Important: The crankshaft position (CKP) system variation learn procedure is required when the following service procedures have been performed, regardless of whether DTC P0315 is set:
?€¢
Engine replacement


?€¢
Engine control module (ECM) replacement


?€¢
Crankshaft damper replacement


?€¢
Crankshaft replacement


?€¢
CKP sensor replacement


?€¢
Any engine repairs which disturb the crankshaft to CKP sensor relationship

Important: The scan tool monitors certain component signals to determine if all the conditions are met to continue with the CKP system variation learn procedure. The scan tool only displays the condition that inhibits the procedure. The scan tool monitors the following components:
?€¢
CKP sensor activity--If there is a CKP sensor condition, refer to the applicable DTC that set.


?€¢
Camshaft position (CMP) signal activity--If there is a CMP signal condition, refer to the applicable DTC that set.


?€¢
Engine coolant temperature (ECT)--If the engine coolant temperature is not warm enough, idle the engine until the engine coolant temperature reaches the correct temperature.

Apr 04, 2016 | Chevrolet Cars & Trucks

2 Answers

Where is the crankshaft position sensor located on a 2008 HHR 2.2 is that ecotec engine


My info says it is located above the starter motor. Info says to remove the starter.

The info also says you have to do a crankshaft variation relearn procedure. I can't help you with that procedure.

Nov 18, 2015 | Cars & Trucks

1 Answer

2005 Dodge Neon SXT 2.0L crankshaft position sensor location to replace


P0315 - Crankshaft Position System Variation Not Learned
P0335 - Magnetic Crankshaft Position Sensor Electrical Error China OBD2 car diagnostic tools wholesale on CareUCar

Mar 20, 2014 | 2005 Dodge Neon SXT

1 Answer

Troubleshoot crank position sensor location


For testing crank sensor,check the help link below:---How to test Crankshaft Position Sensor? http://fordrepairhelp.blogspot.in/2012/03/how-to-test-ford-focus-crankshaft.html
----------

How to test Crankshaft Position CKP Sensor?

---------------
Crankshaft Position Sensor Operation?

----------------
Replace Camshaft position sensor and Crankshaft Position Sensor? http://technoanswers.blogspot.in/2012/06/2005-dodge-durango-replace-camshaft.html
----------
GMC Crankshaft Position (CKP) Sensor Replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-crankshaft-position-ckp-sensor.html

------------
These details will help.
Thanks.

Nov 25, 2012 | 2000 Cadillac Escalade

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

1 Answer

Where is the location of the crankshaft position sensors on a 97 Cadillac Deville. It stalls at red lights and stop signs and I've heard a new crankshaft position sensor is a possible solution. I've got...


The check engine light doesn't have to come on with a bad crank sensor ,your vehicle has two , one for lower rpm an one for higher speeds . A&B
The two crankshaft sensors are located on the front bank (BANK 2) of the engine block between cylinders 4 and 6. Crankshaft position A sensor is located in the upper crankcase and crankshaft position B sensor is located in the lower crankcase. Both sensors extend into the crankcase and are sealed to the engine block with O-rings. The crankshaft position sensors are not adjustable.

Nov 18, 2017 | 1997 Cadillac DeVille

2 Answers

I need to put a crankshaft sensor but I don't Know its location I already changed the cam sensor. Ronnie


The crank sensor is located on the engine near the flywheel axis of the crankshaft.

Crankshaft Position Sensor Removal & Installation To Remove:
Location of the crankshaft position sensor on the 2.4L engine 90904g51.gif
Location of the crankshaft position sensor on the 3.0L engine 91154g20.gif
Location of the crankshaft position sensor on the 3.3L and 3.8L engines 91154g21.gif
NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect the crankshaft position sensor electrical connector.
  4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.
To Install:
NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.
  1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
  2. Connect the crankshaft position sensor electrical connector.
  3. Lower the vehicle.
  4. Connect the negative battery cable.
prev.gif next.gif

Jul 31, 2010 | 1996 Plymouth Grand Voyager

1 Answer

04 Dodge SRT 4 crankshaft sensor


The Crankshaft Position Sensor is located directly next to the starter.
  1. On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
  2. Remove the Structural Collar
  3. Unlock and disconnect the electrical connector to the crankshaft position sensor.
  4. Remove the crankshaft position sensor bolt.
  5. Remove the sensor
Reverse Order to install except note that:

Use a twisting motion when installing the sensor.

Install and tighten the crankshaft position sensor bolt and tighten to 9 N·m (80 ±15 in. lbs.).

Aug 15, 2008 | 2004 Dodge SRT-4

Not finding what you are looking for?
2007 Toyota FJ Cruiser Logo

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...