Question about 1994 Mitsubishi Magna

Open Question

Window regulator Electric window regulator

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

1 Answer

Electric windows repair & partsmotors but does go up gears?


The windows are controlled by electric window regulators. They are cable regulators with electric motors. They average in price around $100, new.
If your window is up, don't put it down until you have the regulator replaced. Otherwise you may end up stuck with the window in the down position and no way to get it up.

Jul 26, 2010 | 1996 Lincoln Town Car

1 Answer

Replace rear door window motor?


GM Grand Am/Achieva/Calais/Skylark/Somerset 1985-98

Electric Window Motor -REMOVAL & INSTALLATION


410c4fe.jpg


Fig. 1: Location of the front door window regulator-1995 vehicle shown (click for zoom)

641fb9e.jpg

Fig. 2: Exploded view of the rear door window regulator-1995 vehicle shown (click for zoom)
  1. Remove the window regulator assembly from the door.
  2. Remove the motor from the regulator by drilling out the attaching rivets with a 3/16 in. drill bit.
To install:
  1. Connect the window motor to the regulator with 3/16 in. rivets.
  2. Install the window regulator assembly.

Hope helps (remember rated this).

Jul 08, 2010 | 1997 Buick Skylark

2 Answers

I need help with replacing the driver side window in a 2003 ford f-150,four door super crew cab truck.


Removal & Installation
Motor - Front Door
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch
  3. Remove the front door trim panel and watershield.
  4. Tape the window in the full UP position.
  5. Disconnect the window motor electrical connector.
    NOTE Support the window motor while removing the window motor retaining screws.
  6. Remove the window motor bolts and remove the motor.
  7. To install, reverse the removal procedure.
Rear Door
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch.
  3. Remove the rear door trim panel and the rear door trim watershield.
  4. Remove the door speakers.
  5. Tape the window glass in the full UP position.
  6. Disconnect the window regulator electric drive.
  7. Position the connector for the window regulator electric drive inside of the door.
  8. Remove the bolts.
  9. Separate the window regulator electric drive from the rear door window regulator.
  10. Remove the window regulator electric drive from the door.
  11. To install, reverse the removal procedure.

Motor & Regulator

3d4a07e.jpg

Fig. Front Door Trim Panel

7932e42.jpg


Fig. Rear Door Trim Panel-Crew Cab


Regulator - Power Windows

506866e.jpg

Fig. Window regulator arm nuts


db15984.jpg

Fig. Window regulator bolts

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch.
  3. Remove the door trim panel.
  4. Remove the door speaker.
  5. Remove the door watershield.
    NOTE Do not remove the window glass from the door.
  6. Remove the window glass from the window regulator.
  7. Tape the window glass in the full UP position.
  8. Disconnect the window motor electrical connector (power windows only).
  9. Loosen the window regulator arm nuts and pull the arm from the mounting position.
  10. Loosen the bolts and remove the window regulator.
  11. To install, reverse the removal procedure.

Hope helped with this. Good luck.

Nov 16, 2009 | 2003 Ford F150 Regular Cab

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

Electric window close just half way only


hello velazqj, sounds like maybe the window regulator is binding, or possibly the window motor itself. Try helping the window up by pulling up on the glass when closing and see if it closes fully. If you hear any funny grinding or crunching noises, the regulator has most likely failed. The regulator is a scissor design and the motor is directly bolted to it. I would recommend removing the door panel and having both inspected.

Apr 23, 2009 | 1996 BMW 318

1 Answer

Power window problem. engauges then disenguages


Section 01-11: Glass, Frames and Mechanisms 1997 Windstar Workshop Manual REMOVAL AND INSTALLATION Door Glass and Regulator, Power Windows Removal
svw~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel (23942) and front door inside panel sound insulator (20394). Refer to Section 01-05 .
  1. Remove inside door belt weatherstrip.
  1. Remove front door window glass (21410) as described in this section.
  1. Remove two nut and washer assemblies attaching the window regulator equalizer arm bracket (23230).
  1. Remove four rivets retaining the front door window regulator base plate to door inner panel.
  1. Remove front door window regulator (23200) and front door window channel bracket (23288) from vehicle.
  1. Working on a bench, carefully bend tab flat to remove front door window regulator arm slides from front door window channel bracket.
  1. NOTE: Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket. Make sure rubber bumper is installed properly on new front door window channel bracket, if replacement is made.

    Install new front door window regulator arm plastic guides into front door window channel bracket and bend tab back to 90 degrees.


    a9ef3ee.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive (23394) are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Door Glass and Regulator, Power Windows .

  1. Install window regulator electric drive with preassembled front door window channel bracket into vehicle. Set the regulator base plate to door inner panel using base plate locator tab as a guide.
  1. NOTE: Two 1/4-20 x 1 inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (35-44 lb-in). Equivalent metric retainers may be used.

    Install four rivets to retain front door window regulator to door inner panel.
  1. Install window regulator equalizer arm bracket.
  1. Lower front door window regulator arms to access holes in door inner panel. Install front door window glass as outlined.
  1. Install inside door belt weatherstrip.
  1. Adjust front door window glass to make sure it is properly aligned with glass run. Check window for smooth operation.
  1. Install front door trim panel and front door inside panel sound insulator. Refer to Section 01-05 .


    Door Glass and Regulator
ac1dac5.gif

Item Part Number Description 1 21410 Front Door Window Glass 2 23288 Front Door Window Channel Bracket 3 23394 Window Regulator Electric Drive 4 23230 Window Regulator Equalizer Arm Bracket 5 222A00 Front Door Glass Run Latch Side Retainer 6 N621906-S36 Nut and Washer 7 N800510-S36 Screw 8 23200 Front Door Window Regulator 9 W525172-S Rivet 10 W525175-S Rivet 11 — Wire Connector (Part of 14630 Wire Assembly) A — Tighten to 7-10 Nm (62-89 Lb-In)

Apr 13, 2009 | 1997 Ford Windstar

1 Answer

Replace a window regulator in a 1994 ford explorer


wow, a lot of work to do.

Window Regulator, Front Door, Explorer Removal
srk~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .
  1. Remove inside door belt weatherstrip and glass stabilizer.
  1. Remove front door window glass as described in this section.
  1. Remove two nut and washer assemblies attaching the equalizer bracket.
  1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .
  1. Remove window regulator electric drive and front door window channel bracket from vehicle.
  1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .
  1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.

    4a5a8fb.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.
  1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.
  1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
  1. Install equalizer bracket.
  1. Install inside door belt weatherstrip and glass stabilizer.
  1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.
  1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.
  1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

Apr 11, 2009 | 1994 Ford Explorer Limited

1 Answer

The right rear electric window won't roll up all


the window regulator is going bad,it has a up cable and a down cable so I would replace it before it wont go up at all,they are pretty inexpensive around $70.00 at a decent parts house,its a pretty simple job, remove the door panel,locate window to regulator bolts.remove them,take glass out thru top, locate 3 bolts that hold motor assy. remove them take bolts holding regulator in place remove them,take motor and regulator out thru holes in door.you can do it! have a good day DB

Feb 27, 2009 | 1991 Honda Accord

1 Answer

Electric window


that means the window regulator assembly needs to be replaced there is not way to fix the same and if you do it it will come of again so just get a new window regulator and replace it.

Jun 10, 2008 | 1997 Lincoln Town Car

Not finding what you are looking for?
1994 Mitsubishi  Magna Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...