Question about 1999 Dodge Durango

3 Answers

Wont shift properly

My check engine light came on and when I ran a diagnostic it said it was my throttle position sensor I have replaced the sensor twice and the light is still coming on after I reset the computer and it still wont shift properly

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Try the speed sensor located on the rear of the trans 20$ part if not then its the pcm

Posted on Jun 23, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Try this, Fill your gas tank to the brim and make sure that the cap is on tight, start your durango and drive down to the closest Knechts auto center and have them turn the sensor off with one of thier tools, This should fix it, the problem with new vehicle such as the 99 Durango is that is the gas door is just a tiny bit not tightend than It will throw all of your sensors off

Posted on Jun 15, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

You may have bad wiring, or a bad PCM. Check the wires back to the computer for breaks, or shorts. If not, you probably need a PCM.

Posted on Jun 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Transmission shifts hard, at times hard to get into gear


if it is a manual transmission then broken mounts are always a good place to start looking
next is a clutch problem nor disengaging properly--again a mount problem
if it is an auto the the mount is immaterial as it will be a selector sensor problem

Jun 23, 2016 | 2004 Lincoln LS

2 Answers

Po 122 problem light on had changed sensor problem not fixed trans not shifting right horrible jurks when it shifts.


P0122 is TPS signal low, which could mean you have a bad TPS, or a fault in the wiring or connector. I suspect a bad Throttle Position Sensor.

Apr 08, 2015 | 2000 Subaru Outback

1 Answer

Codes 32 75 12 22 on a check engine light


first code it's P0320 Possible causes
- Faulty Ignition/Distributor engine speed sensor
- Faulty Crankshaft Position sensor
- Ignition/Distributor engine speed sensor harness is open or shorted
- Ignition/Distributor engine speed sensor circuit poor electrical connection
- Low battery charge
- Faulty Engine Control Module (ECM)


Read more: http://engine-codes.com/p0320_ford.html#ixzz3DcwddSlp
2- P0750 Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Faulty shift solenoid 1 valve
- Shift solenoid 1 valve harness or connectors
- Shift solenoid 1 valve circuit is open or shorted


Read more: http://engine-codes.com/p0750_ford.html#ixzz3DcwoXS73
3- P0120 Possible causes
- Faulty Throttle Position Sensor
- Throttle Position Sensor circuit is open or shorted
- Throttle Position Sensor poor electrical connection


Read more: http://engine-codes.com/p0120.html#ixzz3Dcx3VCPs
4- P0220 Possible causes
- Throttle Position Sensor (TPS) harness is open or shorted
- Throttle Position Sensor (TPS) circuit poor electrical connection
- Faulty Throttle Position Sensor (TPS)
- Fault Electric Throttle Control Actuator (or Throttle Body Motor)
- Accelerator Pedal Position Sensor (APP)


Read more: http://engine-codes.com/p0220.html#ixzz3DcxGUMl4

Sep 11, 2014 | 1991 Ford F150

1 Answer

P0068 on a 2006 Dodge Ram 1500 SLT. Rough "hunting" for idle. Momentary lag/loss of power from a stop. Random RPM changes while at a constant speed. Sometimes it feels like it drops out of gear...


P0068 Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of power
- Engine rough idle Possible causes - Large vacuum leak
- Leaking air duct system
- Mass Air Flow (MAF) poor electrcial connection
- Manifold Absolute Pressure (MAP) poor electrcial connection
- Faulty Mass Air Flow (MAF) sensor
- Faulty Manifold Absolute Pressure (MAP) sensor
- TP sensor not seated properly.
- Faulty Throttle Position (TP) sensor.
- Dirty throttle body
When is the code detected? The Powertrain Control Module (PCM) monitors operation rationality check by comparing sensed throttle position to mass air flow readings
P0068 DODGE Description The Powertrain Control Module (PCM) monitors a vehicle operation rationality check by comparing Throttle Position (TP) to Mass Air Flow (MAF) readings. If, during a self-test, the comparison of the TP sensor and MAF sensor readings are not consistent with the calibrated load values, the test fails and a diagnostic trouble code is stored in continuous memory.

Jul 10, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

I have a 1998 Jeep Grand Cherokee Laredo 4x4. The check engine light came on a little bit ago, and ever since then it's had problems shifting out of first gear. I'll be running 4000 rpm for miles before it...


it is most likley the throttle position sensor"mine wouldn't shift into 5th gear because of it" if it bad or worn out it not sending the correct signal to the computer telling the transmission to shift out. before you get lied to by the auto parts stores diagnostics.turn the ignition on with out cranking the vehicle turn it on off on off and on if the check engine light starts flashing count the flashes .say it flashes two times then pauses then flashes three more times then stops that would be fault code 23 you can look it up on the internet or buy a haynes repair manual in your case if it flashes 2 times then pauses then flashes 4 more times it is the throttle position sensor

Dec 22, 2010 | 1998 Jeep Grand Cherokee

1 Answer

How do i check the throttle positioning sensor on an 04 Mitsubishi Endeavor to see if it is bad.Service engine light is on. diagnostic tool wont clear the tps high voltage code. I need to know the process...


YOU NEED A DIAGNOSTIC SCANNER THAT WILL SHOW YOU TPS SENSOR OPERATION.WITH THROTTLE CLOSE TPS SENSOR VOLTAGE OUT PUT 0 AS YOU MOVE THROTTLE OPEN THE TPS SENSOR VOLTAGE SHOULD INCREASE TO 5.0 VOLTS THATS WIDE OPEN THROTTLE.

Mar 08, 2010 | 2004 Mitsubishi Endeavor

2 Answers

How to change a throttle position sensor on a 94 ford f150 5.0 4x4


How to Replace a Throttle Position Sensor
(DIY & Save up to $135.75 ) - Time: 2.1 hours

Parts:
1. Throttle Position Sensor - $ 55.44

Tools:
1. Scan Tool
2. Screwdriver
3. Multimeter

Procedure:
1. Locate the OBD data link connector (DLC). Refer to your owner’s manual for the specific location.
  • Tip: The OBD-I data link connector is usually located in the engine compartment near the battery or the fuse box. The OBD-II connector (post 1995 cars) is usually located beneath the instument panel next to the steering column.
2. Turn your key to the“ON” position. Do not start the engine.

3. Plug your scan tool into the OBD data link connector. Turn on the scan tool and select the appropriate steps to read the diagnostic trouble code (DTC).

    6db8845.jpg

Scanner plugged into OBD-II data link connector.
  • Tip: The OBD-II diagnostic trouble code (DTC) is a 5 character alphanumeric code. The first digit is a letter that indicates the component group, the second digit is OBD mandated or manufacturer specfic, the third digit is a subgroup, and the fourth and fifth digits define the component and basic problem.
  • 4. Locate the throttle position sensor.
6182d26.jpg

  • Throttle position sensor

  • 5. Disconnect the electrical connector from the throttle position sensor.
fc565b1.jpg

  • Electrical connector removed
6. Test the resistance of the throttle position sensor (TPS) with a digital multi-meter. If the resistance is out of specifications, the TPS must be replaced.
  • 7. Remove the throttle position sensor.

  • d3a8007.jpg

    Removing sensor mounting screws

    8. Install the new throttle position sensor. Tighten the mounting screws and attach the electrical connector.
  • 9. Erase the diagnostic trouble code (DTC) with the scan tool using the“delete” or“erase” command. Road test your vehicle to see if the check engine light returns.
fde01cf.jpg

    Check engine light

  • Tip: If the check engine light returns, repeat the diagnostic process for additional DTCs or take your vehicle to a certified repair shop.
Direct OE replacement

Hope helped with this. Good luck (remember rated this help).

Nov 05, 2009 | Ford F-150 Cars & Trucks

1 Answer

Delay in shifting when excelerating


throttle position sensor, but check fuel filter first

Jan 03, 2009 | 2004 Chevrolet Tahoe

1 Answer

2003 nissan altima 2.5s transmission rough shift


Probably sensors! I have already replaced the crankshaft positioning sensor once, nissan replaced it once under recall and now it is bad again! Plus my speed sensor is bad too! Go to any part store and get diagnostic test ran, it will tell what sensors are bad.

Sep 25, 2008 | 2003 Nissan Altima

Not finding what you are looking for?
1999 Dodge Durango Logo

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...