Question about 2006 Mitsubishi L200 2.5

1 Answer

How to change oil pan

Can you change oil pan without removing the engine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 435 Answers

Try jacking the car up instead? Here's a link to a mitsubishi service manual with diagrams of a motor.
http://www.mitsubishi-motors.kiev.ua/Manuals/Engine/pwee9067/11B.pdf

Posted on Mar 30, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 Saturn vue with the 2.2L engine. I have an oil leak from either the top or bottom pan. Can the lower pan be removed without removing the engine?


Definitely, assuming you're talking about the oil pan. Drain the oil, remove the pan bolts, remove old gasket and clean it. Reinstall oil pan with a new gasket and your done. Don't over tighten your pan bolts! They will snap, or damage your oil pan, especially if it's made of aluminum.

Sep 29, 2017 | Saturn Cars & Trucks

1 Answer

How do you change the oil pump in a 1995 chevy lumina 3100


You must remove the oil pan. I do not think you can do this with the engine in the car. If you can remvove the pan from the bottom without engine removal, it would be easy. Most every engine has to be removed to fully remove the oilpan. So my solution is- remove engine, remove oilpan, remove pump, replace pump, pan, and engine.

Dec 04, 2013 | Chevrolet Lumina APV Cars & Trucks

1 Answer

I have a 93 grand Jeep Cherokee Laradeo ,to change the oil pan seal , and or the oil filter housing to change the O rings , or the timing cover seal or the rear seal , dose one need too lift up or pull...


The oil filter housing and the timing cover can all be worked on with engine in car.
For the rear engine seal (rear main seal), the transfer case and transmission will have to be removed to access the seal.
Most of the time, the oil pan can be removed without raising the engine. Check your clearance under there for anything obstructing removal. (I loaned out my Jeep manual and never got it back!) On some cars, engine needs to be raised about 4 inches for pan to clear the oil pickup tube. Don't know about your Jeep.

Nov 07, 2011 | 1993 Jeep Grand Cherokee

2 Answers

Where is the oil pump located on a 1990 Lincoln Town Car 5.0 v8


the oil pump is located inside the oil pan and has to be removed to get to the oil pump.

Jul 19, 2011 | Lincoln Town Car Cars & Trucks

1 Answer

Is there ANY way to change the oil pan gasket on a S10...


Remove motor mount bolts and rear transmission crossmember bolts or nuts,suppport engine/trans. see if u have enough clearance between pan and axle remove pan. if not, split the exh away from the manifolds. worth a try

Dec 22, 2009 | 2001 Chevrolet S-10

1 Answer

Difficulty in changing the oil pan gasket I dont have the car here to look at do I have to remove any type of crossmember bracing or is it a direct shot to remove it


It's a direct shot....

Removal & Installation
  1. Disconnect the negative battery cable. Raise and safely support the vehicle.
  2. Drain the engine oil into a suitable container.
    1. Remove the transaxle converter cover.
  3. For 1986-90 vehicles, remove the starter motor from the vehicle, as outlined in Section 2.
  4. Remove the oil filter.
  5. If equipped, disconnect the oil level sensor.
  6. For 1996-99 vehicles, remove the oil level sensor. On these vehicles, the oil level sensor must be removed prior to removing the pan. If the pan is removed first, damage to the sensor may occur.
  7. Remove the oil pan-to-engine bolts and the oil pan. Remove and discard the oil pan gasket. The formed rubber oil pan gasket cannot be reused.
  8. If necessary, remove the oil pump pipe and screen.
  9. Thoroughly clean the gasket mounting surfaces.
To install:
  1. If removed, install the oil pump pipe and screen. Secure with the retaining bolt(s) and tighten to 89 inch lbs. (10 Nm).
  2. Place a new formed rubber gasket in the oil pan flange.
  3. Position the oil pan and secure with the oil pan-to-engine bolts. Tighten the bolts to 124 inch lbs. (14 Nm). Do NOT overtighten the bolts, as this will damage the oil pan, causing a leak.
  4. For 1986-90 vehicles, install the starter motor and transaxle converter cover.
  5. Install a new oil filter.
  6. For 1996-99 vehicles, install the oil level sensor.
  7. If equipped, connect the low oil level sensor wire.
  8. Carefully lower the vehicle.

WARNING Operating the engine without the proper amount and type of engine oil will result in severe engine damage.


  1. Fill the crankcase with the proper type and amount of engine oil.
  2. Connect the negative battery cable, then start the engine and check for leaks. Check the oil level and add if necessary.

Oct 05, 2009 | 1991 Buick LeSabre

1 Answer

My oil pan is cracked and I want to know if I have to remove the engine to change this.


If you can see and get to all of the bolts which hold the oil pan to the bottom of the engine and if it appears obvious that the oil pan can be removed without being blocked by anything else, then you don't have to remove the engine. Come to think of it, I don't think that I have ever seen a car where you had to remove the engine in order to remove the oil pan.

Apr 20, 2009 | 2005 Chevrolet Cobalt

3 Answers

Replace oil pump


Oil Pump is in the oil pan.. You would have to take the pan out. To get the pan out you either have to raise the motor up or remove crossmembers.

Mar 23, 2009 | 1984 Toyota Celica Supra

Not finding what you are looking for?
2006 Mitsubishi L200 2.5 Logo

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...