Question about 2009 Chevrolet Malibu

Open Question

Radio and blinker no sound 09 malibu

And seat belt

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
ginko
  • 19396 Answers

SOURCE: 2008 Chevy Cobalt: cd player

Hi.

The problems you are experiencing are caused by the wiring inside the steering wheel. The radio input changing at random is the effect of a contact in the steering wheel control interface. If you have no steering wheel control interface check at the back of the radio for a short in steering wheel control connector's contacts.

The clicking noise when you turn is not coming from the flasher relay, but it is simulated and played by the same system that plays the seat belt chime. If both noises are gone it is probably because of a problem the wiring that goes to the internal car audio system or because a short circuit has impaired both functions.

Problems with steering column wiring are quite common in new Chevy Cobalt. GM has not issued yet any recall for such problems. Here a forum.

There is instead a recall to prevent sudden loss of power steering assist. The recall has been issued to face a critical problem, as loss of power steering while driving may represent an hazard. The recall will entitle you to a free power steering pump and control replacement. I suggest going to the nearest dealer place and asking about the recall. While the steering column is being disassembled to carry the repair you can also ask to have a look at the wiring in there.

Below recall number and details. Mention the recall number when you ask the dealer about repair conditions. The repair under recall is supposed to be free of charge.

10023D SEP 10 Recall - Loss Of Power Steering Assist- Here GM official bulletin: Recall Bulletin.

Regards.

Ginko

Posted on Aug 31, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 trailblazer with the key on the seat belt light will not come on how to go about fixing this problem


To diagnose a failure of the fasten safety belts indicator refer to Symptoms - Seat Belts .
Fasten Safety Belt Indicator/Chime Inoperative
Step
Action
Yes
No
Schematic Reference: Seat Belt Schematics
Connector End View Reference: Seat Belt Connector End Views
1
Did you review the Diagnostic Starting Point - Seat Belts?
YES - Go to Step 2
NO - Go to Diagnostic Starting Point - Seat Belts
2
Did you perform the Diagnostic System Check - Instrument Cluster ?
YES - Go to Step 3
NO - Go to Diagnostic System Check - Instrument Cluster
3
Turn ON the ignition, with the engine OFF.
Observe the seat belt indicator illumination during bulb check.
Does the seat belt indicator illuminate during bulb check?
YES - Go to Symptoms - Seat Belts
NO - Go to Step 4
4
With a scan tool, observe the Driver Side Belt Status parameter in the SIR scan tool data list while buckling and unbuckling the driver seat belt.
Does the seat belt parameter change state?
YES - Go to Step 8
NO - Go to Step 5
5
Test the signal circuit of the seat belt switch for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 11
NO - Go to Step 6
6
Test the ground circuit of the seat belt switch for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 11
NO - Go to Step 7
7
Test the seat belt switch for an open or high resistance.
Does the seat belt switch have an open or high resistance?
YES - Go to Step 9
NO - Go to Step 10
8
Replace the IPC. Refer to Instrument Cluster Replacement in Instrument Panel, Gages and Console.
Did you complete the replacement?
YES - Go to Step 11
--
9
Replace the LF seat belt switch. Refer to Front Seat Belt Buckle Replacement .
Did you complete the replacement?
YES - Go to Step 11
--
10
Replace the inflatable restraint sensing and diagnostic module (SDM). Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .
Did you complete the replacement?
YES - Go to Step 11
--
11
Operate the system in order to verify the repair.
Did you correct the condition?
YES - System OK
NO - Go to Step 2

Jan 08, 2018 | Seat Cars & Trucks

1 Answer

How to replace rear-left seat belt?


un do the bolts that hold the seat belt rewinder
take out the back seat and then undo the bolt that holds seat belt to floor of car then install whole replacement seat belt unit inset and retighten the bolts.
http://www.carparts.com/toyota/camry/seat-belt

Oct 13, 2015 | 2009 Toyota Camry LE

1 Answer

Subaru how to unlock seat belt


Not quite sure what you mean by got around passenger seat. But if the seat is blocking the belt from retracting, then you only need to unbolt the seat from the floor enough to manipulate the belt around the seat. Or just completely unbolt it all the way, you just need a 14mm deep socket and a ratchet. But if you mean the belt just won't retract, then you'll need a new retractor assembly. I hope this info helps!

Aug 22, 2014 | 2010 Subaru Outback

1 Answer

Toyota Echo 2003 SRS light with ABS light blinking instead of Seat Belt Light


When you sit in the seat and put the seat belt on does everything work ok . If so look to the fact that you are required to wear a seat belt and the fact that you are not might be the problem.

Mar 09, 2014 | Cars & Trucks

1 Answer

How to disable seat belt warning beeps?


First... You should have your passengers wear the seat belts but if you insist you can find the wire going to the seat belt buckle and unplug it under the seat.

Jan 14, 2014 | 2006 Toyota Prius

1 Answer

1988 Chevy 1500 pickup, seat belt light stays on, but the buzzer stops when the seat belt isengaged


The weight sensor in the seat is bad if this is the passenger seat. When you connect the seat belt, the sensor is disabled.

Sep 19, 2012 | Chevrolet C1500 Cars & Trucks

1 Answer

Install seat belt through seat belt guide 1990 camaro


The new seat belt guides will have a **** in them that allows you to put the belt through it. If it's a used guide taken off another car it may not have the ****.

Mar 16, 2009 | 1990 Chevrolet Camaro

1 Answer

Seat Belt repair/replace


  1. Remove front seat.
  2. Remove adjuster cover. A
  3. Slide floor anchor cover.
  4. Remove floor anchor bolt. B
  5. Remove shoulder anchor bolt. C
  6. Remove front and rear kicking plate, then remove center pillar upper and lower garnish.
  7. Disconnect seat belt pre-tensioner connector.
  8. Remove the screw securing seat belt pre-tensioner retractor, then remove seat belt and seat belt pre-tensioner retractor.
  9. Remove bolts securing seat belt adjuster, then remove seat belt adjuster. Reverse procedure to install.J

Nov 03, 2008 | 2000 Nissan Maxima

2 Answers

Add middle seat belt to make 3 seat belts on a bench seat?


I'll begin by saying I'm surprised there isn't a 3rd belt on a bench seat, but I think you are entering dangerous territory. There is an immense amount of engineering, testing, and development involved in seat belt systems. They are anchored very securely at points that are reinforced and designed to withstand a human body being thrown against the belt, transferring the energy to the anchors of the belts. So, besides being beyond the scope of being possible to install by your average mechanic, I shudder to think of the legal angle. If u were to be involved in an accident, and someone was injured or worse in that seat wearing the added belt, the lawsuit possibilities are scary. Having said all this, check with your local dealer, maybe the Durango is set up somehow for an extra belt, but I've never heard it before.

Oct 13, 2008 | Dodge Durango Cars & Trucks

1 Answer

Seat belt signs keeps beeping whilst wearing seat belt


just make sure u have nothing an the passager seat becuse any weight on that seat the car thnks there is someone sitting there with no seatbelt on ( no handbags left on the seat) if this is whats worng just plug in the other seat belt. if this is not whats wrong look under the seat and there is two wires comeing from the seat bel buckle disconconect them or join them one or the other will work ( be careful not to touch the air bag wires located in the middle of the seat in yollow plug)

Oct 10, 2008 | 2005 Volkswagen Golf

Not finding what you are looking for?
2009 Chevrolet Malibu Logo

Related Topics:

263 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...