Question about Acura Integra
Driver side wiper goes all the way down to the hood (overlapping the passenger wiper) then all the way up passing the windshield and off the car. How can i fix that?
Remove the wiper arm, and reposition the arm to another position, then try it out to see where it lands. Keep doing that until you find the optimal position. ALSO, On my "teg, the driver's side wiper is 1 inch longer than the passenger side, so be sure you are using the correct length wiper.
Posted on Apr 28, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
It will not be the motor, it will be the linkage or the wiper is slipping on the shaft, the lingkage is accsessible under the cowl, Hope this solves your problem and Merry Christmas
Posted on Dec 22, 2008
SOURCE: my driver side windshield wiper
I just solved this problem last night with my '05 Impala, and ultimately the solution was what newton5083 stated above. Yet, it may also be this (I found it online somewhere):
You have bent or broken the "park tab" on the windshield wiper motor bracket. The correct way to fix this is to remove the wiper arms, wiper linkage and wiper motor from the wiper motor bracket, and install a new bracket.
I just bent the tab back into place a couple times for our daughters 2005 Impala but it kept getting bent down again when they didn't take the time to make sure the wipers were not frozen to the windshield, or tried running the wipers to remove heavy snow on the windshield. So yesterday I fabricated a small piece of metal and bolted that to the bracket in the same place the tab stop was.
If someone wants to access this bracket and tab-
1. Use a ½ inch or 13mm socket & ratchet or wrench to remove nuts on wiper arms.
2. They may make a special tool to remove the arms, I used a screwdriver and hammer to tap bottom of the arm to wedge them apart from the spindle.
3. Two small button-looking clips hold the drivers side cowl cover in place under the windshield. These are two-piece clips, pry up the center, than the outer piece.
4. Unclip the washer hose from cowl cover, than pull out plastic cover.
5. There is a smaller plastic cover with on plastic button head holding that cover in place. Gently pry under that clip to remove that cover.
6. Now you can see the wiper trans and bracket. You should see a small tab on that bracket that looks pushed down and bent or possible a square small hole with some torn off metal where the tab broke off.
7. Remove small plastic cover over the wiper transmission and you can see a small spring-loaded arm underneath the wiper transmission assembly.
8. You need to find something to pry that tab back up so when the wipers are running that spring loaded little arm just snaps past the tab running clockwise. It's when you shut off the wipers that the wiper transmission assembly reverses rotation counter clockwise and the small spring loaded arm underneath hits that tab stop, than the wipers will go all the way down and shut off as they should.
Once that tab stop gets bent out of the way the little spring loaded arm has nothing to stop the wiper transmission assembly so it keeps traveling counter clockwise until some other stop shuts the wipers off straight up on the windshield.
There is a revised bracket part # which is supposed to be more durable, GM part #12368639. Here is a copy of the TSB which points out this problem:
Bulletin No.: 05-08-43-003A
Date: March 10, 2005
Windshield Wipers Park in Up Position (Replace Windshield Wiper Motor Bracket)
2005 Chevrolet Impala, Monte Carlo
This bulletin is being revised to make a correction to the Parts Information. Please discard Corporate Bulletin Number 05-08-43-003 (Section 08-Body and Accessories).
Some customers may comment that the windshield wipers park in the out wipe (vertical) position.
This condition may be caused by a bent park tab on the windshield wiper motor bracket.
To correct this condition, replace the wiper motor bracket. It will be necessary to transfer the following parts listed below to the new bracket.
^ Wiper transmission
^ Wiper motor crank arm
^ Wiper motor
1. Remove the windshield wiper motor drive system module.
2. Remove the windshield wiper transmission from the windshield wiper motor bracket.
3. Remove the wiper motor crank arm from the windshield wiper motor.
4. Remove the windshield wiper motor from the bracket.
5. Install the windshield wiper motor to the new bracket.
6. Install the wiper motor crank arm to the windshield wiper motor.
7. Install the windshield wiper transmission to the windshield wiper motor bracket.
8. Install the windshield wiper motor drive system module.
A TSB is not a recall, if vehicle is still under warranty the dealer should be repaired for free. If not, you'll have to pay for the repairs.
Posted on Jan 08, 2009
Sounds like you just nee to remove them and reinstall them in the correct position. Take them off, run the wipers for one cycle until they park. Install the arms so the blade is about an inch above the bottom of the windshield.
Posted on May 02, 2009
Tips for a great answer:
Mar 29, 2016 | 2012 Nissan Juke S 4dr Hatchback 1.6L...
Oct 20, 2015 | Ford Cars & Trucks
Sep 23, 2012 | 1994 Acura Integra
May 20, 2012 | 2000 Saturn Ls 4dr Sedan
Jan 20, 2012 | 2000 Saturn Ls 4dr Sedan
Oct 24, 2009 | 2000 Saturn Ls 4dr Sedan
May 31, 2009 | 1994 Jeep Cherokee Country
May 02, 2009 | 1995 Honda Accord
75 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: