Question about 2005 Daewoo Matiz

Open Question

How to disconnect fuel rail

Hello how do you disconnect the fuel rail from the fuel pump? My car is 2001 we are trying to pinch it but it isn't moving... Help

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the fuel filter located in the Mercury Mountaineer?


All you have to do is google your automotive questions

The answers & pictures are there already in print

Appears to be in fairly plain site, in front of the fuel tank
next to the frame cross member

Would be nice if everyone at least looked under their vehicles,
before coming here, or state if they plan on working on a vehicle

May 23, 2014 | 2001 Ford Expedition

2 Answers

Fuel pressure 1998 jeep grand cherokee 4.0 L V6


You should have a test port on the Fuel Supply rail, use a tool from a local auto parts "Tool Loaner program" where you can borrow tools for free,w/a deposit of course,then follow the steps provided;

MPI Fuel System Pressure Test

The MPI fuel system used in vehicles equipped with a 4.OL engine employs a vacuum balanced pressure regulator. Fuel pressure should be approximately 55-69 kPa (8-10 psi) lower with the vacuum line attached to the regulator than with the vacuum line disconnected. System fuel should be 214 kPa (31 psi) with the vacuum line connected to the regulator and 269 kPa (39 psi) with the vacuum line disconnected. CAUTION: Some fuel may be discharged when connecting fuel gauge to fuel rail.
  1. Connect a 0-414 kPa (0-60 psi) fuel pressure gauge to test port pressure fitting on fuel rail (Fig. 7).
  2. Remove vacuum line from pressure regulator.
  3. Start the vehicle.
  4. Note gauge reading. With vacuum line disconnected, fuel pressure should be approximately 269 kPa (39 psi).
  5. Connect vacuum line to pressure regulator. Note gauge reading. Fuel pressure should be approximately 214 kPa (31 psi).
  6. If fuel pressure is not approximately 55-69 kPa (8-10 psi) higher with vacuum line removed from regulator, inspect pressure regulator vacuum line for leaks, kinks or blockage. CAUTION: Fuel pressure will rise to as much as 655 kPa (95 psi) when the fuel return tine is pinched shut, shut engine down immediately after pinching oft fuel return line.
  7. If fuel pressure is low, momentarily pinch shut the hose section of the fuel return line. If fuel pressure remains low, inspect the fuel supply line, fuel filter, and fuel rail inlet for blockage. If fuel pressure rises replace fuel pressure regulator.
  8. If fuel pressure is above specifications, inspect the fuel return line for kinks and blockage.

Capacity Test

  1. Remove the cap from the pressure test port in the fuel rail.
  2. Connect a 0-414 kPa (0-60 psi) fuel pressure gauge to the pressure fitting on the fuel rail (Fig. 7).
  3. Start the vehicle. Pressure should be approxi- mately 214 kPa (31 psi) with the vacuum hose connected to the pressure regulator and 269 kPa (39 psi) with the vacuum hose removed from the pressure regulator.
  4. If the pressure is not to specification, check the following before replacing the fuel pressure regulator:
  • 4a - Inspect the fuel supply and return lines/hoses for kinks or restricting bends
  • 4b - Check the fuel pump flow rate. A good fuel pump will deliver at least 1 liter of fuel per minute with the fuel return line pinched off. If the fuel pump does not pump adequately, then inspect the fuel system for a plugged fuel filter or fuel pump inlet filter (sock). Fuel pump flow rate can be done by connecting one end of an old A/C gauge hose to the fuel test port on the fuel rail and inserting the other end of the hose into a container of at least 1 liter capacity. Run the fuel pump by installing a jumper wire into diagnostic connector terminals D1-5 and D1-6. Be sure to pinch off the fuel return line or most of the fuel will be returned to the fuel tank.

May 19, 2014 | 1996 Jeep Grand Cherokee

1 Answer

How to replace fuel pressure regulator 1990 topaz


dont know model but if i was you i would get a fuel pressure guage to see the pressure to the fuerl rail ,, most cars would hae a couple of barpressure ,,, if its getting to filter then if pump is ok it should be at rail... unless you have a blockage ,,,

Dec 01, 2013 | 2001 Pontiac Grand Am SE

1 Answer

I have a 2001 Mazda protege. Has new fuel pump and pressure regulator, I have cleaned fuel tank , lines, rail, and injectors. Relays and fuses are good. I took breather off and sprayed fuel into throttle...


sounds like an electrical problem .pump isnt coming on .turn on key listen for fuel pump to come on for 10 seconds then shut off on its own. If you dont hear the pump then its probley fuel relay . next check wires are plugged into fuel pump. lots of cleaning ?? is the fuel rail screen plugged ???? disconnect before rail if the pump comes on next. turn on key check for fuel pumping out line .

Nov 21, 2013 | Cars & Trucks

1 Answer

2001 dodge stratus fuel pump turns on but no fuel coming through fuel line, change fuel pump relay, still doesn't pump fuel to engine.


I will assume there is fuel in the tank if so then i would say the pump is bad or there is a pinched line, a 2001 stratus it may be the pump.

the only other thing would be if the injectors where not working, if you could put a fuel pressure gauge on the injector rail to see if there is any pressure, this will tell you if it is the pump or something else.

Oct 06, 2012 | Cars & Trucks

1 Answer

Fuel injector diagram 2001 lincoln ls v8


This will provide a basic how to or DIY on how to replace your injectors, but for your specific application, we recommend you ask in our car forum.

Before You begin, It is essential to de-pressurize your fuel system. Disconnect the power to your fuel pump, by either disconnecting it's power supply, or pulling the fuel pump fuse or relay. Once the fuel pump has no power or relay installed, crank the engine for a few seconds. The engine might start, but should die a few seconds later. If it continues to idle, then you didn't disconnect your fuel pump or the correct relay.

Once the fuel system is de-pressurized, you can begin to remove various parts from the engine bay to help clear up room. On a typical system, there is a fuel feed, and fuel return. For these types of systems, you would need to disconnect both of the lines, and then disconnect the fuel pressure regulator. The fuel injectors are held in with clips that hold the harness to the injector. Remove these clips, and pop off the wiring harnesses. The fuel rail is held in with a few bolts. Remove these bolts, and then the fuel rail should be loose. Pull the fuel rail out of the intake manifold or cylinder head, and you can now easily remove the fuel injectors.

Make sure to cover the holes that are now in the intake manifold or head. Don't let any debris fall into this hole!

Pull the old fuel injectors out of the fuel rail, and then put the new injectors into the fuel rail. Make sure you have new "o" rings and you are all set. Simply put everything back together, and then don't forget to plug your fuel pump back in. The car may be hard to start the first few cranks as the fuel pressure builds, and then you are all done!


Diagrams for the above can easily be found in a Haynes or Chiltons Manual - Failing that look on the web, Best of luck.

Sep 05, 2012 | 2001 Lincoln LS

1 Answer

I have a 1998 Chev Monte Carlo SS, The engine turns over but doesn't start. It seems to not be getting fuel but am not sure.


disconnect the hose that goes into the fuel injectors rail, put it into an empty coke bottle and ask for a friend to put the ignition switch in the on position. if there isn't gas going into the bottle, then you should check for the fuel pump relay and if it's ok then check the fuel pump. Check the fuel pump fuse too.

Jun 27, 2011 | 1998 Chevrolet Monte Carlo

1 Answer

I had my bed off of my 93 cheyv s-10 and the truck was running good then when i put thebed back on i started the truck and drove ou tof my garage when the head lights shut off and the truck died and now...


all the wiring for the fuel pump and tail lights run along the frame rail take the bed back off check all the wiring for pinch marks and cracked casings then check all ur fuses i had to replace my pump in the tank took bed off had a bugger of a time getting it back on without pinching them ... good luck to ya

Jun 01, 2011 | 1993 Chevrolet S-10

1 Answer

I suspect fuel pump problem how do I check fuel pressure, what tools do I need


There should be a Schrader valve on the fuel rail (looks like a valve stem on a tire, it is metal).

You need to connect a fuel pressure gauge to that valve and do the following test:

  1. Relieve fuel pressure.
  2. Remove the 12 mm sealing nut from the fuel rail. Attach the fuel pressure adapter nut, 12 mm (90201 - P0A - 003) and the special tool.
  3. Start the engine. Measure the fuel pressure with the engine idling and the vacuum hose of the fuel pressure regulator disconnected from the fuel pressure regulator and pinched. If the engine will not start, turn the ignition switch on, wait for two seconds, turn it off, then back on again and read the fuel pressure. Pressure should be: 260 - 310 kPa (2.7 - 3.2 kgf/sq.cm, 38 - 48 psi)
  4. Reconnect vacuum hose to the fuel pressure regulator. Pressure should be: 210 - 250 kPa (2.1 - 2.8 kgf/sq.cm, 30 - 37 psi) If the fuel pressure is not as specified, first check the fuel pump. If the fuel pump is OK, check the following:
    • If the fuel pressure is higher than specified, inspect for:
    • Pinched or clogged fuel return hose or line.
    • Faulty fuel pressure regulator.
    • If the fuel pressure is lower than specified, inspect for:
    • Clogged fuel filter.
    • Faulty fuel pressure regulator.
    • Fuel line leakage.

Jul 27, 2009 | 1997 Honda Accord

Not finding what you are looking for?
2005 Daewoo Matiz Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

yadayada
yadayada

Level 3 Expert

77201 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...