Question about 2008 Ford F-350

1 Answer

I bought a used 2008 ford f450. The nav sys says to clean the disk. How can I find the pin code that the original owner set up. There are no owners manuals.

In the security screen,the valet is set. to eject the nav disk I need the pin code that was set up by the original owner of the truck

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

This is from page 38 of the navigation system manual. I hope it is the right one for your system:

" If the PIN is forgotten, you
can disable Valet Mode by disconnecting the battery or removing the
appropriate fuse for one minute to reset the system."

Here is a link to the manual:

http://www.fordservicecontent.com/Ford_Content/catalog/owner_guides/08pnosn3e.pdf

Posted on Mar 31, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the reset swicth on ford 2000 super duty v10


I looked at owners manual for f450. This info is in your owners manual. If you don't have an owners manual, www.fleet.ford.com has owners manuals you can look at.
26392388-ubfaq4jwace1utdszsxx1x2i-4-0.jpg

Dec 09, 2016 | Ford Cars & Trucks

1 Answer

Code for a 2008 Ford focus 1.6 radio Hi, I am looking for the code for a 2008 Ford focus 1.6 radio since I disconnected the battery. serial number - 304706770931 Thanks,


The code should usually be on a sticker or similar in the original manual for the radio. Sometimes it is in the car's owners booklet.

Aug 21, 2014 | Cars & Trucks

1 Answer

Were is the location of battery in aston martin 2009 vantage


The battery should be located on the right, under the luggage compartment removable floor panel. You must re-enter the radio/sat nav code after power is restored. Your radio owner's manual describes the procedure very clearly. The radio code will be embossed on a card found in the owner's manual dossier.

Jan 22, 2013 | 2008 Aston Martin V8 Vantage

1 Answer

I need to know which fush munber is for chime beep for 2003 ford f450 superduty


it's in our owner manual. the fuse chart.

go to motorcraft.com,pro center, tech info, owner guide, fuse chart in index.

May 20, 2011 | Ford F-450 Cars & Trucks

1 Answer

2008 Ford F450 6.4 code P0088 3 times, ( check engine light on ) dealer will clear code, and it sets code P0088 again. dealer has no fix yet ( 90000 miles )


Hello, you might try a new fuel rail pressure sensor. This Code 0088 is for high pressure at the fuelrail. It would be possible to rig a testing pressure gauge to the truck and drive it to see what the pressure really is. If the dealer has a Dyno, he could run it in the shop.

Some of the reports I am reading is the Turbo boost for other owners is starting to max out about 70-75 MPH with a load and usually going up a grade before this light comes on. A certified Pressure gauge would show whether the sensor is tripping too early.

I want to believe there are some specs the Dealer could use to bench test this sensor. But if the end result is buying a sensor and paying Labor you could just go Aftermarket and install a New sensor yourself.

Would like to know the final solution on this.

Feb 04, 2011 | 2008 Ford F 250 Super Duty 4WD

1 Answer

Bought used 2008 ford edge and don't know former owners combination to the security touch pad on door. Is there any way to reset it so we can use it?


You will need to contact the dealer and they will have to get some information about you and the car before they will give the code, or reset it for you.

Nov 28, 2010 | 2008 Ford Edge

2 Answers

I bought a used 2008 ford escape. No owners manual. How do I reset the keyless entry. I don't know the original code.


did you mean the key pad on the door? if it is then you need to track down the original owner to give you the factory code then you can program up to 3 codes.
give the local dealer a call to see if they can run the VIN number for a factory code, they may charge you a fee.
if you bought it from a dealer then they must take care of that for you at no charge.
otherwise you will need to replace the key pad.

Mar 25, 2010 | 2008 Ford Escape

1 Answer

GMC Nav Map for Mexico


youll need a scanner from the dealer TECH 2 or equiv...

Dec 11, 2008 | 2008 GMC Sierra 2500HD 2WD

Not finding what you are looking for?
2008 Ford F-350 Logo

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...