Question about 2010 Dodge Journey

Open Question

Neutral park switch

P0850

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I get my 2004 Dodge Ram 3500 5.9 48re out of limp mode?


http://www.cumminsforum.com/forum/911-urgent-situations/909314-p2769-p0973-2007-5-9-w-48re-limp-mode.html#/topics/909314?_k=cp8azv&nocache=1469908570493

this is for the Cummins but sounds like the issue you are having. Not sure why the voltage would go so low as to cause an issue...makes me suspect a failed component inside the tcm (assuming that is where the voltage comes from) causing low voltage to the circuts.

Jul 30, 2016 | Dodge Cars & Trucks

1 Answer

MT. What are the probable causes of DTC P0850?


Faulty park / neutral switch or bad wiring

Dec 04, 2015 | 2006 Nissan 350Z

1 Answer

2006 Honda accord code po706 what is that


Possible causes
- Faulty Park/neutral position switch
- Misadjusted park/neutral position switch
- Park/neutral position switch harness is open or shorted
- Park/neutral position switch circuit poor electrical connection


Sep 18, 2014 | 2006 Honda Accord

1 Answer

Po 705 code


Possible causes
- Faulty Park/Neutral Position Switch
- Misadjusted Park/Neutral Position Switch
- Park/Neutral Position Switch harness is open or shorted
- Park/Neutral Position Switch circuit poor electrical connection

May 29, 2014 | 2001 Chevrolet S-10

1 Answer

Ford trouble code


- Open or short park/neutral position switch circuit
- Poor park/neutral position switch circuit connection
- Misadjusted park/neutral position switch
- Park/neutral position switch may be faulty

Aug 13, 2012 | Ford Expedition Cars & Trucks

1 Answer

P 0705 transmission range sensor circuit malfunction code for a 2001 mitsubishi galant can i replace it and where is it located


P0705 - Transmission Range Sensor Malfunction. The park/neutral position (PNP) switch includes a transmission range switch. The transmission range switch detects the selector lever position when the shift lever is in the N or P shift position and sends a signal to the Transmission Control Module (TCM). The possible causes of this are the following: Open or short park/neutral position switch circuit. Poor park/neutral position switch circuit connection. Misadjusted park/neutral position switch. Park/neutral position switch may be faulty. Inspect the pnp switch and replace if needed.

Jan 15, 2011 | Mitsubishi Galant Cars & Trucks

1 Answer

I HAVE A 1990 LS 400 WHEN TURNING KEY NO CRANKING AND HAVE GOOD BATTERY POWER. NO POWER TO STARTER WIRE ON STARTER SELINOD.WHAT CAN IT BE


It could be a bad ignition switch or bad starter wire from the starter switch, or the PNP is not adjusted correctly:

Here are instructions on how to remove and replace the PNP, but read over it to understand how to adjust:
Park/Neutral Safety Switch REMOVAL AND INSTALLATION ES300 1993-94 Models
  1. With the ignition switch in the LOCK position, disconnect the negative battery terminal. If equipped with an air bag system, wait at least 90 seconds or longer before performing any other work.
  2. Raise and safely support the vehicle.
  3. Disconnect the Park/Neutral switch connector.
  4. Remove the clip from the shift control cable.
  5. Remove the nut and control cable.
  6. Remove the bolts and pull out the Park/Neutral switch. To install:
  7. Install the Park/Neutral switch and loosely install the bolts.
  8. Adjust the switch and torque the bolts to 48 inch lbs. (5 Nm).
  9. Install the control shaft lever.
  10. Install the control shaft cable and torque the nut to 9 ft. lbs. (13 Nm). Fig. 1: The transaxle control shaft lever has a nut and washer to retain it - 1993-94 ES300 54617.gif
    Fig. 2: Removing the Park/Neutral switch - 1993-94 ES300 54618.gif

  11. Install the clip to the shift control cable.
  12. Lower the vehicle.
  13. Connect the negative battery cable.
  14. Make sure the vehicle will start only in the PARK or NEUTRAL position.
1995-97 Models Fig. 3: Aligning the neutral base line and groove - 1995-97 ES300 293716.gif
Fig. 4: Park/Neutral switch removal and installation - GS300, LS400, SC300 and SC400 300569.gif
Fig. 5: Park/Neutral switch adjustment - GS300, LS400, SC300 and SC400 300571.gif
  1. With the ignition switch OFF, disconnect the battery cables, negative terminal first. Allow 90 seconds to elapse before performing any other work.
  2. Apply the parking brake fully and block the rear wheels.
  3. Disconnect the electrical connector from the Park/Neutral position switch.
  4. Remove the locknut and disconnect the control cable from the manual shift lever.
  5. Remove the clip from the holding the control cable to the bracket.
  6. Remove the nut, washer and the manual shift lever from the manual valve shaft.
  7. Using a flat bladed tool, bend the lock washer back away from the nut.
  8. Remove the nut and lock washer from the Park/Neutral switch.
  9. Remove the two bolts and the Park/Neutral position switch. To install:
  10. Install the Park/Neutral position switch to the manual valve shaft. Leave the two bolts loose at this time.
  11. Install the lock washer and nut. Torque the nut to 61 inch lbs. (7 Nm).
  12. Using a flat bladed tool, bend the lock washer over the nut to secure the nut in place.
  13. Adjust the Park/Neutral as follows:
    1. Install the manual shift lever to the Park/Neutral switch and set the shift lever to the neutral ( N) position.
    2. Align the groove and the neutral basic line on the Park/Neutral switch.
    3. Hold the Park/Neutral switch in this position and tighten the two bolts to 48 inch lbs. (5 Nm).
  14. Install the manual shift lever with washer and nut.
  15. Install the control cable to the manual shift lever and install the nut. Torque the nut to 11 ft. lbs. (15 Nm).
  16. Install the control cable to the bracket by installing the clip.
  17. Connect the electrical connector to the Park/Neutral switch.
  18. Lower the vehicle and check the vehicles shifting positions.
  19. Connect the negative battery cable to the battery.
  20. Verify that the vehicle only starts in PARK or NEUTRAL.
GS300, LS400, SC300 and SC400
  1. With the ignition switch OFF, disconnect the battery cables, negative terminal first. Allow 90 seconds to elapse before performing any other work.
  2. Raise and safely support the vehicle.
  3. If necessary, remove the front exhaust pipe.
  4. Disconnect the neutral start switch connector.
  5. Remove the control shaft shift lever.
  6. Pry off the washer and remove the nut.
  7. Remove the bolt and pull out the neutral start switch. To install:
  8. Install the Park/Neutral switch and loosely install the bolt.
  9. Adjust the switch as follows:
    1. Loosen the neutral start switch bolt and place the shift lever in the N position.
    2. Align the groove and the neutral basic line.
    3. Hold in position and tighten the bolt to 9 ft. lbs. (13 Nm).
  10. Install the nut and washer.
  11. Install the control shaft shift lever.
  12. Connect the electrical connector.
  13. Install the front exhaust pipe. Torque the front nuts to 46 ft. lbs. (62 Nm). Torque the pipe support bracket to bolts to 32 ft. lbs. (43 Nm). Torque the No. 2 front exhaust pipe to the front exhaust pipe bolts to 32 ft. lbs. (43 Nm).
  14. Lower the vehicle.
  15. Connect the negative battery cable to the battery.
  16. Verify that the vehicle will only start in the N or P positions.
---
Maybe try to press the brake pedal and run the gear shift throughout the full range of gears while the car is on level ground, and retry the starter to see if there is a faulty PNP adjustment.

Try to start in Neutral not Park, and jiggle the gear shift back and forth to see if the PNP is not adjusted right.

Good luck on this repair.

Nov 09, 2010 | 1992 Lexus Ls 400

1 Answer

2001 toyota sequoia- car won't start on park.. but starts on neutral...mechanic says it's the neutral safety switch..it is??


sounds like park safety switch,there are 2 switches 1 neutral and 1 park, if it starts in neutral,it is working,if in park,and does not start usually means bad switch or wire off.

Dec 23, 2009 | 2003 Toyota Sequoia

Not finding what you are looking for?
2010 Dodge Journey Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...