Question about 1998 Saab 900

1 Answer

Bleed hydraulic clutch

NOT INOF PEDAL TO OPERATE CLUTCH

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Saab Master
  • 3,679 Answers

There will be a bleed nipple on the clutch slave cylinder ,when bleeding same process as brake bleeding but push the padal VERY slowly as could push piston past usual use point and then the rubber seals may pull from piston

Posted on Mar 30, 2014

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

saabreur
  • 51 Answers

SOURCE: clutch fluid leak

the 900 uses the same reservoir for both brake and clutch; it's in front of the firewall on the side of the pedals, immediately visible when you open the hood. Milky plastic, with a screw top; max and min levels marked by lines.

clutch leaks can be at the slave cylinder in the clutch, which will likely cause slipping clutch; at the master cylinder, which may show as fluid inside the car; or in line between them (runs from master cylinder at firewall to front of engine, where the clutch is located).

Look for leaks on ground and relate to location above leak in engine bay

Saabreur

Posted on May 30, 2009

burgessjay69
  • 78 Answers

SOURCE: my clutch pedal is on he floor and wont disengauge the clutch

maybe it lost all the fluid as may be leacking from slave cylinder the carpit will be wet with fluid or the slave cylinder could be gone in that case the bellhouseing on the gear be will be wet with fluid or at least the thrust bearing could have gone thought the clutch cover

Posted on Jun 22, 2009

  • 41 Answers

SOURCE: clutch pedal falls to floor

the clutch fluid maybe low or you may have a bad clutch slave or master cylinder

Posted on Nov 20, 2009

Testimonial: "How do I determine which would be the first to replace there is no noticable fluid leaks any where "

  • 6 Answers

SOURCE: clutch is sticking

is it hydraulic.? or cable.. the clutch , if it is cable replace it

Posted on Apr 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Does Toyota hilux R150 gear box have a clutch adjustment ?ie master cylinder adjustment ?


If it is adjustable it will have a threaded push rod at the slave cyl ,bleed the hydraulic system first adult the clutch then bleed again .

Oct 26, 2015 | Toyota Cars & Trucks

1 Answer

Miata clutch


With engine off, does the shifter get gears easily?
If so, it could be your hydraulic clutch. Check the fluid level on the clutch master cylinder's reservoir-on the firewall. If it is low, add brake fluid to it. If it was dry, you will probably have to bleed the hydraulic clutch down at the slave cylinder on the transmission bell housing.
When clutch pedal is pressed, the clutch master cylinder will force fluid down the line to the small slave cylinder. There, a small plunger is forced out (about an inch or less) from the slave cylinder, and pushes the clutch fork forward. The fork causes the clutch inside the bell housing to operate. Look for this movement of the slave cylinder pushing the clutch fork while someone presses down or pumps the clutch pedal. With the engine off, of course.

Jan 28, 2014 | Cars & Trucks

1 Answer

Ford Bantam rocam Clutch: How do I bleed the clutch?


Clutch bleeding on hydraulic slave cylinders are done in the exact same method as regular hydraulic brakes. If the slave cylinder has a separate reservoir, make sure it is above "MINIMUM" at all times. If it does not have a separate reservoir, then it works together with the master cylinder for the brakes, make sure that one is above minimum too. Pump the clutch pedal a couple of times (note you will rarely feel any resistance in the pedal), hold the pedal down, and have someone open the bleeder valve on the slave cylinder. Close it when no more fluid comes out with pressure, then rinse and repeat until the clutch pedal feels ok.

Jan 09, 2014 | 2006 Ford Bantam 1.6i

1 Answer

Clutch pedal goes to floor and half works on my b2200 1987 mazda pick-up


If the clutch is hydraulic operated, you need to bleed the clutch at the slave cylinder, down on the transmission housing. Bleed it just like you bleed brakes of air in the line-open bleeder valve, someone pushes clutch pedal slowly to floor, close valve, and repeat until fluid comes out valve in a steady stream. Make sure the clutch reservoir is full before starting. It uses regular brake fluid.
If not hydraulic, it would be cable operated. Adjust the cable until clutch pedal is right.

Dec 29, 2012 | Cars & Trucks

1 Answer

Pt cruiser clutch diagram


I recommend bleeding the clutch using instructions pasted from autozone.com below. As for the engine light, please get the computer scanned and send us the diagnostic trouble code.
Hydraulic System Bleeding NOTE
It is necessary to bleed the clutch hydraulic release system if the system has lost an excessive amount of fluid and has allowed air into the circuit. Air in the system typically results in a spongy pedal feel, and/or improper clutch release. If air cannot be removed from the system using this procedure, it is necessary to replace both the clutch master cylinder and slave cylinder assemblies.

Except Turbocharged Models
  1. From driver's seat, actuate clutch pedal 60-100 times. Verify clutch operation/pedal feel. If pedal still feels spongy, or clutch does not fully disengage, excessive air is still trapped within the system. Perform the following procedure:
  2. Verify fluid level in clutch master cylinder reservoir. Top off with DOT 3 brake fluid as necessary.
  3. Raise and safely support the vehicle.
  4. Remove clutch slave cylinder assembly from the transaxle case, but do not disconnect from the system. Allow the slave cylinder hang, making it the lowest part of the system.
    CAUTION
    While slave cylinder is detached from the transaxle, DO NOT actuate the clutch master cylinder. Damage to the slave cylinder will result.
  5. Depress slave cylinder pushrod until it bottoms and then release. Repeat this at least ten times, forcing trapped air upwards and out of the system.
  6. Re-install slave cylinder into position. Torque slave cylinder to case bolt to 168 inch lbs. (19 Nm).
  7. Carefully lower the vehicle.
  8. Check and adjust clutch master cylinder fluid level. Actuate clutch pedal thirty (30) times. Verify clutch operation/pedal feel. If pedal still feels spongy, or clutch does not fully disengage, air is still trapped within the system. Repeat Step 3 through Step 7 until air is purged. If several attempts at purging air from the system are unsuccessful, replace both the clutch master cylinder and slave cylinder assemblies.
  9. Raise and safely support the vehicle.
  10. Carefully lower the vehicle.
  11. Top off clutch master cylinder fluid level with DOT 3 brake fluid as necessary.
Turbocharged Models

NOTE
Due to the angle and design of the turbo hydraulic system components, gravity and pedal bleeding are less effective and less efficient than the reverse fluid injection method (reverse bleeding). Reverse bleeding is recommended for this system, and requires the use of commercially available injection bleeding equipment.

Alternate Procedure (Pedal Bleeding)
  1. Remove reservoir cap and inspect fluid level. Top off with DOT 3 Brake Fluid. Actuate clutch pedal briskly at least 50 times. Verify release system function. Repeat. If release system is still inoperative, continue with procedure.
  2. Raise and safely support the vehicle.
  3. Remove clutch bellhousing access cap to expose system bleed screw.
    WARNING
    Use care not to allow fluid to drain into clutch bellhousing. Excessive fluid will be agitated and sprayed around inside the clutch bellhousing by the rotating flywheel, contaminating the flywheel, disc, and pressure plate, resulting in poor clutch engagement.
  4. Using suitable socket/wrench, loosen bleed screw. Immediately install rubber hose to bleed screw to prevent fluid from entering clutch bellhousing. Tighten bleed screw gently with suitable wrench.
  5. Lower vehicle.
  6. Have helper actuate clutch pedal to floor.
  7. Place collection container at end of hose to capture expelled fluid.
  8. Using suitable wrench, break bleeder screw loose and tighten to 62 inch lbs. (7 Nm). Do not over-tighten.
  9. Have helper release pedal, returning it to at-rest position, and then actuate pedal to floor.
  10. Break bleeder screw loose and tighten to 62 inch lbs. (7 Nm). Do not over-tighten.
  11. Repeat procedure as necessary, keeping master cylinder reservoir full during the process, until air bubbles are no longer visible in collection container.
  12. When air bubbles are no longer visible, actuate clutch pedal briskly at least 50 times.
  13. Verify release system function and top off fluid as necessary.
Recommended Procedure (Reverse Bleeding)
  1. Remove reservoir cap and inspect fluid level. Top off with DOT 3 Brake Fluid. Actuate clutch pedal briskly at least 50 times. Verify release system function. Repeat. If release system is still inoperative, continue with procedure.
  2. Remove reservoir from bracket and empty into collection container.
  3. Raise and safely support the vehicle.
  4. Remove clutch bellhousing access cap to expose system bleed screw.
    CAUTION
    Use care not to allow fluid to drain into clutch bellhousing. Excessive fluid will be agitated and sprayed around inside the clutch bellhousing by the rotating flywheel, contaminating the flywheel, disc, and pressure plate, resulting in poor clutch engagement.
  5. Using suitable socket/wrench, loosen bleed screw.


    Fig. Location of the bleed screw for the 2.4L engine
  6. Quickly attach hand operated bleed apparatus to bleed screw. Use care not to over-fill reservoir and spill fluid into engine compartment.
  7. Operate bleed gun sufficiently to expel air upward through circuit and out of master cylinder reservoir. Fill and empty reservoir three times.
  8. Remove bleed apparatus and tighten bleed screw to 62 inch lbs. (7 Nm). Do not over-tighten.
  9. Carefully lower the vehicle.
  10. Top off reservoir with fluid, then return the cap.
  11. Verify system operation. Actuate clutch pedal 50 times. If necessary, repeat procedure until road test confirms that shift issues no longer exist.

May 20, 2017 | 2002 Chrysler PT Cruiser

1 Answer

Clutch pedal has no resistance like it's not even working. is it the clutch itself or the pedal.


It appears to be a hydraulic clutch so your reservoir is probably empty and there is no fluid to operate the clutch. Try filling the reservoir and bleeding the clutch. If that does not work you will have to overhaul or replace the master cylinder or the slave cylinder. None of the above are really difficult tasks.

Feb 27, 2011 | 1993 Toyota Corolla

1 Answer

Clutch slave cylinder how to bleed


HYDRAULIC SYSTEM BLEEDING Do not use fluid which has been bled from a system to fill the reservoir as it may be aerated, have too much moisture content or possibly be contaminated. Clean the dirt and grease from the cap to ensure that no foreign substances enter the system. It is also important to maintain the fluid level in the clutch reservoir to the top step with hydraulic clutch fluid Hydraulic Clutch Fluid GM P/N 12345347 or equivalent.
  1. Attach a hose to the bleeder screw on the clutch actuator assembly and submerge the other end of the hose in a container of hydraulic clutch fluid.
  2. Depress the clutch pedal slowly and hold.
  3. Loosen the bleeder screw to purge air.
  4. Tighten the bleeder screw to 18 inch lbs. (2 Nm).
  5. Let up on the clutch pedal.
  6. Repeat Steps 2 through 5 until all air is purged from the system.
  7. Fill the reservoir to the top step with hydraulic clutch fluid.
  8. Repeat this bleeding procedure if there is a grinding noise during the clutch spin down procedure.
prev.gif next.gif

Oct 13, 2010 | 1998 Chevrolet Cavalier

1 Answer

My clutch is not angaging need to see how can i bleed


Hydraulic Clutch System BLEEDING The clutch system can be bled using a pressure bleeder. Follow the instructions that come with the pressure bleeder for the proper pressure bleeding procedure. The maximum line pressure while pressure bleeding must not exceed 36 psi (248 kPa). NOTE: To bleed a clutch manually requires the assistance of a second person, a section of hose that is compatible with brake fluid (preferably clear) and fits the slave cylinder bleed screw snugly and a container to catch the fluid that is bled through the system. As brake hydraulic fluid easily absorbs moisture, always use fresh fluid when bleeding a hydraulic system.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. To bleed the system perform the following:
    1. Top off the hydraulic fluid reservoir using a fluid that meets the standards of the vehicle's hydraulic system.
    2. Open the clutch slave cylinder bleed screw and press the clutch pedal to the floor and hold the pedal down.
    3. Close the clutch slave cylinder bleed screw.
    4. Release the clutch pedal.
    5. Check the hydraulic fluid level and top off as necessary.
  3. Repeat the above steps until the discharged fluid is clean and no air bubbles appear during the bleeding process.
prev.gif next.gif

Aug 03, 2010 | 1998 Audi A4

Not finding what you are looking for?
1998 Saab 900 Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

rgbypoet

Level 2 Expert

166 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...