Question about 2000 Toyota Corolla
What is the fuel cconsumtion of a 1.6i 4a engine
Fuel consumption of engines is a question very often asked and seldom answered adequately. There are so many variables that affect consumption so I will give a few
tyre pressure and size
condition of engine
number of passengers
weight of driver
extras on vehicle (roof rack)
tread pattern of tyres
driving conditions (town-country)
driving conditions ( hilly --flat)
slipping into neutral at lights
the list goes on and on so be guided by the expected average of the manufacturer of between 8 litres to 10litres per100kilometers travelled
Posted on Mar 30, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
hey, torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10
Posted on Jan 14, 2009
Tighten in several passes to 44 foot pounds.
I just wanted to add. Since this is an aluminum cylinder head, I hope you loosened the head in the loosening torque pattern. The pattern opposite of the torque tightening pattern. If not, you stand the chance of warping the head.
Again, since it's an aluminum head, it needs to be checked for flatness. Most aluminum heads need to be surfaced before re-installing.
Tightening torque pattern is as follows:
1.The Drivers side of the engine is the Left side.
From the Front going towards the back; the bolts are numbered 10, 6, 1, 3, and 7.
From the Front going towards the back on the Passenger side; the bolts are numbered 8, 4, 2, 5, and 9.
The Exhaust and Intake Camshaft Bearing Cap bolts go to 9 foot pounds. Tighten gradually. One bolt to the other with so many foot pounds, work back, and forth up to 9lbs.
Camshaft Timing Pulley bolts go to 43 foot pounds. (In a tightening sequence, and gradually)
Posted on Jul 25, 2009
This engine utilizes shims to set proper clearances, you will need a micrometer, valve clearance adjustment tool set for shimmed lifters,small magnetic arm, appropriate shim selecting charts (manufacturer will have this if you can get the nec. measurements).
Measure thickness of shims removed (using micrometer) and use this formula where T=Thickness of old shim; A=Valve clearance measured; N=Thickness of new shim required.
Intake valves: N = T + (A - 0.02 mm (0.008 in.)) Exh. valves: N = T + (A - 0.25 mm (0.010 in.))
Then you need to find shims as close as possible to the calculated values.
Valve clearances (cold) are as follows: Intake 0.15 - 0.25 mm (0.006 - 0.010 in.) Exhaust 0.20 - 0.30 mm (0.008 - 0.012 in.)
Note, if you are not familiar with precision measuring using a micrometer, this may be better left to a trained tech. These are high revving little power plants and you don't want a problem at 8K rpm.
Posted on Aug 06, 2009
why does my normal rpm always bug down when the engine start?and when I started to use the air con, the rpm was playing. It doesnt go on a certain point. it always range at 800rpm then it will down to 700. what am I might do to solve this probem?
Posted on Mar 13, 2010
remove the bottom of rear seat. open the service door on rear floor. take out the bolts that hold fuel tank set plate to the fuel tank, then now you can remove fuel pump assembly.
Posted on Sep 24, 2010
Tips for a great answer:
Apr 02, 2017 | 1994 Toyota Corolla
Jun 06, 2016 | 1996 Geo Prizm
Apr 26, 2016 | Toyota Cars & Trucks
Fig. 2: Firing order- 4A-C engine (other A-series similar)
Mar 07, 2011 | 1983 Toyota Corolla Deluxe
Oct 21, 2010 | 1997 Toyota Corolla
Jan 06, 2010 | 1989 Toyota Corolla 2 Door
Apr 30, 2009 | 1991 Toyota Corolla
Jan 14, 2009 | 1985 Toyota Corolla 2 Door
Sep 18, 2008 | 2000 Toyota Corolla
196 people viewed this question
Usually answered in minutes!