Question about 1995 GMC Jimmy

1 Answer

Loseing water out the back end dont know where it is comming from or going to but comes out by the bellhousing

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 321 Answers

Freeze plug sounds like.
check around the back of the heads
if you find a leak in the freeze plug back there and you are able to get it will never get the new one in unless you pull the head.
so use the rubber one with the bolt and nut in the middle.they work very well.

hope this helps
thank you

Posted on Jun 15, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Hyundai Atos 1.1 leaking water by bellhousing What could be the problem

That means your water pump is about to go buddy it's not expensive but just be prepared

Feb 06, 2018 | Hyundai Cars & Trucks

1 Answer


Just little...? This is normal. Every time and first time start the car.
It build up moisture and go out of tail pipe. There is not more when it's hot. (This is normal) Don't worry.

mai lor

Mar 20, 2013 | GMC Jimmy Cars & Trucks

1 Answer

Leaking water from the trasmissin

The transmission is not full of water, it contains a special type of oil that is red in color. What you see is water condensation from the AC system. This is normal drain off.

Jul 08, 2012 | 1995 Chevrolet Chevrolet S 10

1 Answer

Mb100 mercedes benz high pitch noise from black box above engine (inside case) i dont know what it goes on for 8seconds when the ignition is on.. And prior to this it nearly overheated also the...

It sounds like 1 of 2 things with dash lights comming on its possible it could be the bearings in the alternator if the bearings start to colaps or move the bushing inside doesent catch and the lights on your dash come on
or its possible the waterpumps going but usually ,not all the time you will be losing water from the radiator
another cause of sqweeling is the fan belt torsion wheel the bearings in them go causing some sqweeling but i would get the alternator checked hope this helps ivan

Nov 03, 2017 | 2000 Mercedes-Benz M-Class

1 Answer

Is the crankshaft bolt in a 2003chevy malibu reversed

No i dont think so but what i used to do was use the starter motor with my big snap on bar wedged in but do not do this as the crank may not have a keyway and its only held tight by the pulley and if you attempt it the old way you will crunch the valves ,now there is a special tool that fits to a starter motor bolt after taking it out and it looks like a ringear in reverse .Now if you dont have one of these then what i do is look for a hole in the bellhousing showing the timing mark and then i jam it up with a big old screwdriver in the ringear if i cannot get into the ring gear then i drill a 3/8th hole in the bellhousing to line up with the ring gear and then put my screwdriver in their and get willing assistant on the big bar with a tube on the end ,same as tighteneing it up i put a jack on the end of the extension bar then assistant can pull it up to at least 120lbs and the jack takes the strain of the turning motion ,failure to di it this tight will result in it coming loose on the motorway and the valves going bang and maybe a piston as well

Feb 08, 2012 | 2003 Chevrolet Malibu

1 Answer

I dont know were my starter ison my jeep grand cherokee limited 1995 canyou tell me where it is and how to take it out and repair it. thank you

Should be on the passenger side at the back of the engine, going into the bellhousing. Should be 2 bolts holding it on and a couple electrical connections. A rebuilt starter will be about $50 if you bring in your old as a core.

Jun 22, 2011 | 1995 Jeep Grand Cherokee

2 Answers


it has a crank sensor.

Jun 08, 2009 | 1999 Kia Sportage

1 Answer

Need to know the torque settings on the fly wheel and on the clutch &preasure plate on daewoo lanos 1998 manual 1.5 ltr thanks.

put some locktight on the flywheel bolts and make sure they are tight by using a impact gun or jam a screwdriver into ringear and a bellhousing bolt as fulcrum and then pull bolts up with a big snap on knuckle bar and go round twice 1/2 inch drive---clutch use a 3/8 socket set and dont over tighten go round at least 3 times and dont forget to put copper grease on the spigot shaft splines .And remember to top the gearbox oil up with EP90 ,and lightly grease the new rear end oil seal you have obviously changed .

Apr 05, 2009 | Daewoo Lanos Cars & Trucks

2 Answers

Starter removal - 1994 Isuzu Trooper

pull the starter away from the bellhousing and turn the drive end upwards then it will come out from the engine compartment tight i know but i have just done mine so i know it will come

Mar 18, 2009 | 1994 Isuzu Trooper

1 Answer

Cut wire

to your starter

Jun 17, 2008 | 1992 Chevrolet S-10

Not finding what you are looking for?
1995 GMC Jimmy Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides