Question about Honda Odyssey

1 Answer

How to replace 1996 honda odyssey timing cover

Just the timing cover to reach the crank position sensor

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 65 Answers

To get the lower cover off, all belts, and the crank pulley need to be removed. You have the same engine as an Accord of the same year. So, the side mount will need to come out too. You have to support the engine with a jack. (not under the oil pan!!!!) Use a flat block of wood on the jack to distribute weight evenly. Question: Why are you after the CKP sensor? They are not a very common failure item. What problems are you having?

Posted on Apr 01, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 337 Answers

SOURCE: Replacing crank shaft position sensor on 2000 Honda Civic

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528018f5b9

Posted on Dec 10, 2008

SOURCE: 1996 HONDA ACCORD CRANKSHAFT SENSOR AND CAMSHAFT SENSOR.

befor in the ealier models of accords they use to be both the cam and crank sensors in the distibutor but they separated them !!!So no they are not together on your car tha cam sensor is in the distributor and the crank sensor is in front of engine or in the lower timing belt cover if it is in the timing cover you can see a wire going dow the timing cover way to the bottom on the rear side off it

hope it will help you if you have any question just wright back !!!!



Denis

Posted on Dec 13, 2008

motor1258
  • 6674 Answers

SOURCE: crank shaft position sensor needs replacing in 96 Chevy cavalier

Try this.

c6734a6.jpg

Posted on Sep 05, 2009

  • 2 Answers

SOURCE: replacing catalytic converter on a 2002 Honda Odyssey

i have 2002 honda odyssey
engine and tcs light come on after driving 10-15 miles with code p0131, p0132,p0136,p0137

please help me fix my car problem

Posted on Sep 09, 2009

emissionwiz
  • 80407 Answers

SOURCE: replace a crankshaft position sensor on a 1996

1st I need to know what engine you have, 4.0L or 5.2L V8.

Posted on Oct 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What can cause a p0335 code to appear on my 2003 honda odyssey


code p 0335 refers to crankshaft position (CKP) sensor---circuit malfunction=== causes --wiring--CKP sensor ---ECM
at this point because you were in the area doing repairs to the power steering pump , it is possible that you have disconnected the wires to the CKP
check that or replace the CKP

Jun 09, 2018 | Honda Cars & Trucks

1 Answer

2000 odyssey CKP problem code P0335. I replace the crank seal and this code show up after that. then I open again to replace the sensor and code still there. What I can do? thanks


code p 0335 refers to crankshaft position sensor (CKP)---circuit malfunction===causes ---wiring---CKP sensor ---ECM
the wires are a good place to start and check for damaged insulation , broken wires or bad harness connections
next there is an air gap setting between the sensor and the exciter (segmented bars on a ring) on the crankshaft check that is correct ---dimension available from the workshop manual

Oct 06, 2016 | 2000 Honda Odyssey

1 Answer

How many hours of labor on average is it to replace the cam shaft position sensor on a 2004 Honda Odyssey


2 or more. There's a lot of stuff in the way that has to be disassembled to get to the sensor

Jul 16, 2014 | 2004 Honda Odyssey

1 Answer

1996 Honda accord no crank intermittently


cranking is turning the engine over
from you misinterpretation of the term the problem is that it is cranking but not running
if that is correct then yes the cam shaft position sensor may very well be the cause of the not running at times as it controls the ignition and injector operation , the same as the crank shaft position sensor
could be a loose connection that has now come apart or the sensor has finally reached a point of failure that it needs to be replaced

Dec 20, 2017 | 1996 Honda Accord

1 Answer

Location and replacement of crank sensor on honda odyssey 1999


crank sensor is located to the upper right hand side of the crank pulley. you have to remove the pulley to access this. you can test it without removing the pulley though.

Nov 04, 2012 | 1999 Honda Odyssey

1 Answer

WHERE IS THE CRANKSHAFT SENSOR ON A 2000 HONDA ODYSSEY AND IS IT HARD TO GET TO.


on the crank in the front behind the timing belt. thats why it is the money it is. you should replace the timing belt as well since you are there.

Sep 14, 2012 | 2000 Honda Odyssey

1 Answer

1996 Honda Odyssey runs but not full power the codes for TDC senser came up .I erased the code and got a used distributer and still have same problem if i erase the code it comes back as soon as i turn it...


This sensor isn't related to the distributor!!More than like you have a faulty crank sensor. Its located within the lower timing belt cover, which will require crankshaft pulley removal.

May 27, 2011 | 1996 Honda Odyssey

4 Answers

1996 HONDA ACCORD CRANKSHAFT SENSOR AND CAMSHAFT SENSOR.


camshaft sensor is in distributor(requires dist. replacement) crankshaft is behind lower timing belt cover

Dec 12, 2008 | 1996 Honda Accord

1 Answer

1996 HONDA ACCORD CRANKSHAFT SENSOR AND CAMSHAFT SENSOR.


befor in the ealier models of accords they use to be both the cam and crank sensors in the distibutor but they separated them !!!So no they are not together on your car tha cam sensor is in the distributor and the crank sensor is in front of engine or in the lower timing belt cover if it is in the timing cover you can see a wire going dow the timing cover way to the bottom on the rear side off it

hope it will help you if you have any question just wright back !!!!



Denis

Dec 12, 2008 | 1997 Chevrolet Astro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...