Question about 2001 Ford F150 Styleside SuperCrew

1 Answer

Ford 2001 F150 power steering hose

Trying to replace the pressure power steering hose. How do I loosen the upper hose fitting on the steering sector?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

With a wrench.

Posted on Mar 30, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1056 Answers

SOURCE: ppower steering pressure hose 1988

There are only 2 hoses in the power steering system.
High pressure feed, and pressure return. They both connect to the power steering pump.
You can get the hoses from a dealer, or a local auto parts store.
Once you have them in hand, they are very simple to identify.

Posted on Aug 07, 2008

chrischronic
  • 235 Answers

SOURCE: Replace thermostat in 2000 ford ranger

the open pipe that you took the hose off of is the thermostat housing, you will need to remove this to reveal the thermostat, make sure you use a new gasket with sealant when reinstalling thermostat housing to prevent leaks and dont over tighten the bolts,run both bolts down as far as you can before final tightning

Posted on Dec 26, 2008

  • 143 Answers

SOURCE: WHERE IS THE LOW PRESSURE PORT FOR A 2001 FORD F150?

It may be located on/near the evaporator case where the big (suction) line comes out.

Posted on Jun 19, 2009

  • 270 Answers

SOURCE: power steering pump on a 2001 ford windstar

There is a special tool for that. It should be available at most auto parts stores.

Posted on Oct 17, 2009

  • 1075 Answers

SOURCE: power steering pump Ford Focus 2006 DIY Manual

its quite quite simple;take your pipes of and block them off reconnect them to new pump and replace pump to in line belts.adrian;;;

Posted on Nov 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to repair power steering leak?


You need to first diagnose what is leaking. Most power steering leaks are in the pressure hose but not always. Pressure hoses will have screw on fittings and return hoses will usually just have spring clamps or screw type clamps on the end of the hose. Pressure hose most likely, return hoses 2nd, failing rack and pinion assy 3rd and pressure pump last. If its leaking from the bellows on the end of the rack and pinion the you will need a reman unit. Presure pumps are also remanufactured if thats what you need. hoses are replaced with new hoses or standard return hose for the return line.

Jul 12, 2014 | 2001 Ford Windstar

1 Answer

How to change powerstering pump chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Dec 13, 2012 | 2008 Chevrolet Uplander

2 Answers

Replace power steering pump on 06 chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Jul 08, 2012 | 2006 Chevrolet Uplander

1 Answer

How to replace power steering pump on 2001 lincoln ls v8


please rate if this helps. Might find one cheap on ebay.

Power Steering Pump - 3.9L
Special Tool(s) st1444a.gif Teflon® Seal Replacer Set
211-D027 (D90P-3517-A) or equivalent
Removal
  1. Remove four pushpins and the engine cover.
    a0004091.gif
  1. Remove the air cleaner and the air cleaner outlet tube. For additional information, refer to Section 303-12.
  1. Remove the bolts.
    a0001108.gif
  1. Remove the accessory drive belt. For additional information, refer to Section 303-05.
  1. Unclamp and disconnect the power steering reservoir-to-pump hose (3691) and drain the reservoir (3E764) into a suitable container.
    a0001104.gif
  1. Position the power steering reservoir out of the way.
    1. Loosen the bolts.
    1. Rotate the reservoir from the insulator.
    1. Pull the reservoir down from the insulator and position the reservoir out of the way.
    a0001105.gif
  1. Raise the vehicle on a hoist. For additional information, refer to Section 100-02.
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04.
  1. Remove two bolts, one pushpin and the shield.
    a0000396.gif
  1. Remove two pushpins and the shield.
    a0001110.gif
  1. Remove the bolt.
    a0001111.gif
  1. Disconnect the electrical connector and the wire retainer.
    a0001112.gif
  1. Remove four bolts and position the A/C compressor out of the way.
    a0001113.gif
  1. Disconnect the power steering pressure hose.
    a0001114.gif
  1. Remove the bolts.
    a0001115.gif
  1. Lower the vehicle.
  1. Remove the bolts and the pump.
    a0001116.gif
Installation
  1. Using the appropriate special tool, install a new O-ring on the power steering pressure hose fitting.
    a0001117.gif
  1. NOTE: Do not tighten the upper bolts until the lower bolts are installed.

Jun 10, 2011 | 2000 Lincoln LS

1 Answer

How to put in a power steering hose


First loosen the hight pressure hose at the lower end. Drain the fluid into an oil pan. Remove the upper fitting. Take out the hose and replace. Refill with new P.S. fluid and dispose the old at a recycler.

Mar 14, 2011 | 1997 Oldsmobile Silhouette

1 Answer

1991 f-150 ford pickup truck power steering pump


Purchase a replacement pump at Autozone or Kragens. Remove and plug the two pressure lines. Loosen the adjustment braket. Pull the pump over to loosen the belt. Remove the belt. Remove the adjustment bracket. Remove the bolt holding the pump. Replace the pump. Put on the belt and tighten it until there is 3/8 in. flex. Refill the pump reservoir with power steering fluid.

Mar 11, 2011 | 1991 Ford F150

1 Answer

HOW DO YOU TAKE OFF A POWER STEERING LINE? I HAVE A 96 FORD E150 5.8


When power steering hose replacement is required, follow these steps:
  1. With the engine stopped, remove the return hose at the power steering gear, and allow the fluid to drain from this hose into a drain pan. On some cars, the vehicle must be lifted on a hoist to replace the power steering hoses.
  2. Loosen and remove all hose fittings from the pump and steering gear.
  3. Remove all hose-to-chassis clips.
  4. Remove the hoses from the chassis, and cap the pump and steering fittings.
  5. If O-rings are used on the hose ends, install new O-rings. TRW steering gear cylinder lines have gaskets that are serviced as a unit. The old gasket must be pried out of the fittings in the housing before the new lines and gaskets are installed. Lubricate O-rings with power steering fluid.
  6. Reverse steps 1 through 4 to install the power steering hoses. Tighten all fittings to the manufacturer's specified torque. Be sure all hose-to-chassis clips are in place. Do not position hoses where they rub on other components.
  7. Fill the pump reservoir to the full mark with the manufacturer's recommended fluid. Bleed air from the power steering system. Check the fluid level in the reservoir and add fluid as required.

Jul 07, 2009 | 1996 Ford Econoline

1 Answer

Replacing power steering hoses - 2001 Concorde


you can but what are the price of the parts .just a pain to get at the fittings just make sure they are the right hoses and they are put back on the high pressure and low pressure sides .cut the old ones and tap a socket over the fitting rather then wrench might strip it and have troubles geting out and root them the same spot the old ones came from

Mar 03, 2009 | 2001 Chrysler Concorde

Not finding what you are looking for?
2001 Ford F150 Styleside SuperCrew Logo

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...