Question about 2007 Ford Freestar Limited Minivan

Open Question

How do i replace rear caliper on 2007 ford freestar

When replacing rear caliper, how do I remove E brake and do I need to make any adustments to the E brake?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2039 Answers

SOURCE: 1995 Ford Taurus brake pad replacement

the piston need to be turn clock wise and push at the same time make sure when you turn it the rubber around the piston dont get damaged it stick to the piston and get torn before you turn just make sure it not sticking to the piston at the auto part store they sell the toll to turn the piston its cheap$$ hope it FIXYA our post thanks pierre

Posted on Jul 06, 2008

  • 350 Answers

SOURCE: 2006 Ford Five Hundred anti-lock brake pad replacement

hi its rare the pads stick to the rotor but obviously this one was welded metal to metal so if the other sides not down to the metal you won,t have the same problem now getting the piston back into the caliper if you don,t have the tool its going to be fiddling but you need to get some pressure on the piston as to shove it back in not to much as you have stated it has to be screwed back in once a pressure has been applied [could try using you c-clamp ] then the slots in the piston insert something that will turn the piston it will locate and start to screw back your going to need pateince as it is fiddling with the correct tool you may need a few attemps but the other side should not be as bad as the piston has not gone past the point of return take your time and check for leaks when you have them all assembled yates210456

Posted on Oct 17, 2008

Monster80
  • 460 Answers

SOURCE: How to replace rear brake pads on 2006 Ford Freestar?

Before you try and push on the caliper to hard stop..When compressing the caliper it needs to be rotated at the same time it is being press in.Turn clock and push in at the same time..Hope this helps you and take your time..Have a great day

Posted on Apr 02, 2009

jmgldsmth
  • 1869 Answers

SOURCE: R&R rotors and calipers on 2005 Ford 500 to do brake job

use a large c-clamp to bottom out the caliper pistons remove the caliper bolts .slip out the pads and remove the caliper from the disk
hang the caliper from a coathanger wire to avoid damaging the brakeline after replacement of the pads;brake bleeding is not needed Rotors are held on to the axle like a wheel; with bolts

Posted on May 29, 2009

john631068
  • 172 Answers

SOURCE: how take off pins not bolts on caliper 87 Ford Ranger front brake

The pins / wedges just tap out use a scewdriver on the metal edge of the pin just tap it out to the rear and when putting them back in just tap them back in from the front. You will see they are diamond shape and metal cased around rubber very easy to do just take your time.

Posted on Nov 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Ford freestar.. left Rear disc brake locked up.. the pads are shot but do I absolutely have to change the caliper?


You could try striping and cleaning the caliper then rebuilding it if you are able to get a kit to replace the rubber parts and pistons that are damaged

Feb 27, 2017 | Ford Cars & Trucks

1 Answer

Compress rear brake calipers on 2004 freestar


many fords have "spin in" caliper pistons.

Your local auto parts store sells the tools you need. (Multi sided for different sizes)

You insert the tool and spin the caliper piston back in. (many times, they are hard to start turning but should be easy once you get started)

Make sure the cap is off the brake master cylinder so the brake fluid and rise up as you screw in the pistons.

Hope this solves your problem.

Feb 02, 2013 | 2004 Ford Freestar

1 Answer

How to replace 2005 ford freestar rear hub assembly


*Remove the rear tire
*Get yourself an old wire coat hanger (or some bailing wire)
*Remove the 2 - 13mm bolts holding the caliper in place
*Bend the wire/coat hanger and use it to "hang" the caliper on -
basically do not let the caliper hang by its hose.
*Rock the caliper back and forth a little until it comes away from
the caliper bracket, then hang it on your wire.
*Remove the 2 - 18mm bolts holding the caliper mounting bracket
and remove the bracket, set it aside.
*Remove the rotor - You might need to hit it with a rubber mallet to
get it to come lose (rust).
*At this point you should see the hub (the part with the lug studs
sticking out towards you). On the backside of the hub, you should
see 4 studs facing the inward,
*Follow the wire for your wheel speed sensor that is located in the
center of those 4 studs facing inwards (you should see it pretty
clearly) and disconnect it.
*Remove the hub's nuts (15mm if I recall), then swap out your hub
assembly.
*Reconnect the wire

Use the reverse order to put things back together.

Hope this helps!
Cheers

Sep 21, 2012 | 2005 Ford Freestar

1 Answer

Replacing rear brake pads on 2006 Freestar ..piston won't move back with c clamp


I just had this problem myself. I ended up removing the caliper completely and drained it of all of it's fluid. I then held it in my hand and used an 2" round bar to beat the piston back down. once you break it loose it goes fairly easy. then bolt it all back up and bleed the brakes

Jul 11, 2012 | 2006 Ford Freestar

1 Answer

Hubby is trying to replace rear brakes on my 2006 Ford Freestar.Please help!


I'm sure he is trying to figure out how to get the piston into the caliper.

http://www.harborfreight.com/18-piece-disc-brake-pad-and-caliper-service-tool-kit-97143.html

the piston will have to be turned and pressed in at the same time. You could try to muscle it in with a pair of needle nose pliers but this will not be fun and you run the risk of damaging the piston or seal.

http://www.sears.com/shc/s/p_10153_12605_00999811000P?prdNo=8&blockNo=8&blockType=G8

a generic tool like the one above is available at most auto parts stores.

Sep 19, 2011 | 2006 Ford Freestar

1 Answer

Hi i just changed my calipers on my 2005 ford freestar and my brakes are not working is there a quick fix to this problem


There is air in the brake system and must be bled. They have devices for bleeding the system...basically you need to replace the air with fluid. Hope this helps !

Mar 09, 2011 | 2005 Ford Freestar

2 Answers

How to replace rear brake pads on 2006 Ford Freestar?


Before you try and push on the caliper to hard stop..When compressing the caliper it needs to be rotated at the same time it is being press in.Turn clock and push in at the same time..Hope this helps you and take your time..Have a great day

Apr 02, 2009 | 2006 Ford Freestar

1 Answer

Rear brake rotor replacment


206-04: Rear Disc Brake 2000 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  2. Disconnect the brake hose.
  3. Remove bolt.
  4. Disconnect the rear wheel brake hose (2A442).
  5. Remove the copper washers and plug the brake hose.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.

Mar 28, 2009 | 2000 Ford Explorer

1 Answer

2004 freestar


new calipers now. and i had to replace both discs. Ford Freestar is renowned for it's rear brakes wearing prematurely.

anyway, after forcing banging, and utterly destroying two heavy duty c-clamps, i check forums and found you MUST rent a tool from an auto parts store (mine was free loaner from Checker, just had to give them $80 and bring it back undamagaed, they give you back 100% back). Anyway the tool twists the calipers as it pushes them back. you cannot just force the calipers back with straight force.

Jul 06, 2008 | 2004 Ford Freestar

Not finding what you are looking for?
2007 Ford Freestar Limited Minivan Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...