Question about 2007 Peugeot Partner Grand

Open Question

Clutch cable peugeot broken

Clutch cable broken

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: I have just purchased

It can be repaired. From what you have told me it coud be the clutch cable. At the worse it will be a new clutch. I hope you find this information helpful.

Posted on Nov 29, 2008

Ad
  • 8 Answers

SOURCE: clutch slipping

this is how to adjust the clutch correctly

NOTE: From mid-94 an automatically adjusted cable was progressively introduced. this has no nut type adjusters at the clutch end

SPECIFICATIONS: 1988 TO 1996
Models up to 1992 .... 145mm
Models from 1993 on .. 162mm +/- 12.0mm

The clutch adjustment is checked by measuring the clutch pedal travel.
1. If a new cable has been fitted, settle it in position by depressing the clutch pedal at least 20 times.
2. Ensure that there are no obstructions beneath the clutch pedal.
Depress the clutch pedal fully to the floor, and measure the distance from the center of the clutch pedal pad to the floor.
Now release the pedal and again measure the distance from the pedal to the floor.
3. Subtract the first measurement from the second to obtain the clutch pedal travel.
If this is not within the range given in the specifications, adjust the cable as follows.
4. The clutch cable is adjusted by means of the adjuster nut on the transmission end of the inner cable.
On some models, access to the locknut is limited and, if required, the air cleaner duct or housing component can be removed or disconnected to improve access.
5. Working in the engine compartment, slacken the locknut on the end of the clutch cable.
Adjust the position of the adjuster nut, then re-measure the clutch pedal travel.
Repeat this procedure until the clutch pedal travel is as specified.
6. Once the adjuster nut is correctly positioned, and the pedal travel is correctly set, securely tighten the cable locknut.
Where necessary, refit any disturbed air cleaner duct/housing components.

Posted on Feb 13, 2009

  • 2 Answers

SOURCE: PEUGEOT 406 LX DT 1998 2088 CC CLUTCH SLAVE CYLINDER

I understand these cars have a sealed clutch system. When they fail you replace the whole kit master,hydrolic pipe and slave (comes in one piece). Search on ebay maybe £45 or so.

Posted on Feb 26, 2009

alicantecoli
  • 22219 Answers

SOURCE: need instructions on how to fit auto adjusting peugeot 206

cant honestly say i have fitted one on this model,but is it full auto or is their an adjuster on the back of the clutch pedal.??? look first.Ford escort one is a bit of a pig but easy when you have the knack same as a golf easy when you know how .Now golf cable comes with two plastic ties that hold auto adjuster together and you dont relaese them till the cable is fitted.Can you describe the set up then i might be able to help some more.American web site so a lot of models not listed here and the lingo take a bit as well ,i mean whos ever heard of pigs tails or fire wires.Well what else can you expect when they are not taught the queens english and dont drink tea, just waste it by throwing it in the sea.

Posted on Mar 05, 2009

emissionwiz
  • 76673 Answers

SOURCE: how to bleed a hydraulic clutch on a peugeot 406

you need to buy a vacuum clutch bleeding tool make by a company called MITYVAC

Posted on Sep 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Peugeot 307 hdi sw wont go in gaer why?


if it is a manual(not stated ) then the problems as indicated is a clutch not disengaging when depressed
possible causes are
no oil in the system
air in the system
failed clutch master cylinder and /or clutch salve cylinder
If cable clutch then it may be a broken cable.

May 29, 2015 | Peugeot 307 Cars & Trucks

1 Answer

Clutch troubleshooting


Is the clutch hydraulic or cable? in 80's peugeot's they had both depending on engine, if its hydraulic it could be failed seals or a leak, if its a cable it could have snapped, get somebody with a little mechanical knowledge to have a look.

Jul 29, 2014 | 1986 Peugeot 205 Cabriolet

1 Answer

Why dose the clutch pedal stick down on my peugeot ?


The linkage between the pedal and the clutch throwout bearing needs attention - the return spring appears to not have been reinstalled correctly, or has broken.

Jul 29, 2014 | Peugeot 405 Cars & Trucks

2 Answers

Car wont start


is there a cable that hooks to the clutch,it may be broken.it will need to be re attached or replaced if this is the problem

Dec 30, 2013 | 2006 Peugeot 405

1 Answer

My clutch won't go down and won't go into any


ABS light coming on,For this get the Engine computer scanned.It can be error codes stored in computer.------------
For more details regarding this click the link below:-----
The ABS and Traction Control Lights stays ON dash of car? http://schematicsdiagram.blogspot.com/2011/06/abs-and-traction-control-lights-stays.html

---------------
And now for clutch not going in gears it can be faulty clutch issue or problem with clutch cable.This has to be inspected.For more detailed instructions regarding Peugeot clutch problem,click the link below:-----
Peugeot 307: Clutch will no go in gears?
http://whoisbyme.blogspot.in/2012/05/peugeot-307-clutch-will-no-go-in-gears.html

---------
This will help.
Thanks.

May 30, 2012 | 2004 Peugeot 307 SW

1 Answer

I have a peugeot boxer 1.9d van and cant remove the clutch cable from out of bulk head, pedal side as it has snapped, do you have any ideas


If the cable has completely snapped and not attached to the clutch pedal, the whole cable, casing and broken cable should just about fall out of the bulkhead. I have never had a problem with that on any vehicle.

Apr 18, 2011 | Peugeot Liberte Cars & Trucks

1 Answer

Dragging into gear and slipping when driving. nw clutch or cable? ive been told its not my clutch


If there's slippage when driving...it's the clutch. Make sure that the clutch cable is in good order and not jamming as this would give the same effect as a worn clutch.Check the cable inner for broken strands. As the clutch is not breaking enough to allow you to select gears quietly, and as is slipping in the higher gears, I would say it could be worn out too and require a new complete cluch kit installed, if the cable is operating ok.

Apr 09, 2010 | 1991 Peugeot 405

1 Answer

Peugeot 306 clutch


its deffintly the clutch as these cars have a pull type clutch. which means that the clutch will keep going until the car wont move.

Apr 07, 2010 | 1990 Peugeot 405

1 Answer

I recently had a new clutch fiited on My peugeot 406 GLX 1999 model, and lately the gears have been stiff.


this could be 1 of 4 things

you have become use to change characteristics of the old well worn/broken down oil - but even so new oil should not be excessivey stiffer

incorrectly adjusted clutch - although 406s had a self adjuster cable

incorrectly installed clutch

or most probably

wrong gear box oil - i have experience this, garages will use one grade/type of gear oil - check what spec your car is meant to have and change it - it made a huge difference on my peugeot

the oil filler and drain are accessible by removing the road wheel on the gearbox side of the car

Nov 06, 2008 | Peugeot 405 Cars & Trucks

Not finding what you are looking for?
2007 Peugeot Partner Grand Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

mike hayward

Level 2 Expert

279 Answers

lloyd cole

Level 2 Expert

250 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...