Question about Cars & Trucks

1 Answer

Jump &jerks between exeleration deceleration 91 dodge ram 250 passenger van 318-ci

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Sounds like the backlash in your rear deferential needs ajusted.

Posted on Jun 21, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: 1991 dodge ram 250 van 318 engine won't start

ALWAYS CHECK THE GROUND ON A DODGE

Posted on Nov 16, 2008

emissionwiz
  • 74975 Answers

SOURCE: 1997 Dodge Ram 1500 transmission will a 1996 interchange

No, the frame is different.

Posted on Nov 30, 2008

csmock132
  • 4669 Answers

SOURCE: AIR STOPS BLOWING OUT OF VENTS WHEN ACCELERATING

On the side of the intake there is a one way check valve in a vacuum line to the vent controls. Replace it

Posted on Mar 14, 2009

  • 176 Answers

SOURCE: water pump 1996 dodge ram van 318 2500

Before you remove the serp belt, loosen the clutch fan bolts from the water pump. Other wise you will be fighting with them later. Other wise just drain the coolant and remove the pump. I would suggest a new thermostat since the coolant is drained. Make sure the block surface is cleaned of all gasket material and other dirt before installing your new pump. I usually scrape the area with a putty knife and wipe it down with some brake clean on a rag.

Posted on May 20, 2009

  • 30 Answers

SOURCE: how do I remove and replace the steering column of 1992 ram 250 v

remove coupling from top of steering rack ( make sure you mark postition of coupling first with centre punch so the replacement will be in the same position)
remove covers from steering column and ignition + anything else attached to column. good luck

Posted on Jul 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

91 dodge passenger van 250 318- new plugs/wires/dist/rotor cant seem to figure out why it falls on its face at takeoff & lurches @ exeleration&deceleration!!!!! help


Could be a number of things, bad computer, fuel pump, electrical failure somewhere in system, poor ground fault, the list goes on

Mar 29, 2014 | Cars & Trucks

1 Answer

Where do find the distributor cap/wires 91 dodge 250 van


No cover on floor between driver and passenger?

Mar 02, 2014 | 1991 Dodge Ram

1 Answer

91 dodge 250 van w 318 no power to distributor help


does the ignition resistor block have power? check fuses..

Jan 01, 2014 | Cars & Trucks

1 Answer

1996 Dodge Ram 1500 2wd 318/ci


Use the balljoint removal tool to remove. Sometimes a bottle jack comes in handy for the stuck ones. When you put them back on, use a big C-Clamp

You can go to autozone.com and register for full free online repair manual for any vehicle if you ever need it.

Dec 13, 2009 | 1996 Dodge Ram 1500 Club Cab

1 Answer

Need fuse box diagram for 91 dodge ram 150 van


i have the diagram for dodge ram van 250. don't know if it's the same, but i have it. find me at jhiggz11@yahoo.com

Mar 09, 2009 | 1991 Dodge Ram 150

1 Answer

Where is the heater blower motor located and how can i test it to see if it works


should be on the firewall on the passenger side of engine compartment 4 nuts to take off don't forget the plug. hope this helps.

Oct 30, 2008 | 1992 Dodge Ram 250

1 Answer

Wont start


might be a worn ignition wire, check your harness by the triverside engine compartment...estimaternotfree@yahoo.com

Sep 13, 2008 | 1989 Dodge Ramcharger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...