Question about 2010 Volkswagen Tiguan

Open Question

Tiguan transfer case

Remove transfer case

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 chevy blazer transfer case removal


How to Remove a Chevy Blazer Rear Transfer Case The transfer case on a Chevrolet Blazer is underneath the vehicle, mounted to the rear of the transmission. On four-wheel drive vehicles, the transfer case takes power generated by the engine and channeled through the transmission and directs it to the front and rear drive axles. Over time, the gears and bearings inside the transfer case can wear and the transfer case must be rebuilt. The transfer case on this vehicle must be removed before it can be serviced.
Things You'll Need
  • Wrench set
  • Floor jack
  • Jack stands
  • Socket set
  • Masking tape
  • Marker
  • Needle-nose pliers
Hide Instructions
  1. Removing the Driveshafts
    • 1 Disconnect the ground cable from the negative battery terminal, by using a wrench to loosen the retaining bolt and pulling the clamp off the terminal.
  • 2 Raise the vehicle and support with jack stands placed underneath the frame.
  • 3 Drain the transfer case. Locate the drain plug near the bottom of the transfer case. Place a waste oil collection pan underneath the plug and use a socket to remove it. Once all the fluid has drained out, reinstall the plug.
  • 4 Remove the bolts that connect the rear driveshaft to the rear axle yoke using a socket. Lower the driveshaft, and slide it backward underneath the rear axle to disengage it from the transfer case. Remove it from the vehicle.
  • 5 Remove the bolts that connect the front driveshaft to the front axle yoke using a socket. Lower the driveshaft, and slide it forward underneath the front axle to disengage it from the transfer case. Remove the driveshaft from the vehicle.
  • Removing the Transfer Case
    • 6 Label and disconnect the electrical wires and vacuum lines connected to the transfer case. Use masking tape and a marker.
    • 7 Remove the transfer case shifter rod. Using needle-nose pliers, remove the clip that connects the shifter rod to the transfer case. Slide the rod away from the transfer case.
    • 8 Position a floor jack underneath the transfer case. Raise it enough to take the weight of the transfer case off the transmission.
    • 9 Remove the bolts that connect the transfer case to the transmission using a socket or wrench.
    • 10 Slide the transfer case rearward to disengage it from the transfer case. Lower the floor jack, and remove the transfer case from the vehicle

    Jul 27, 2014 | Cars & Trucks

    1 Answer

    I have a 2009 Tiguan. The master power window switch on the driver's side fails to work intermittently. Can I replace this switch without removing the door panel?


    -Possibly. depend on how it was build.
    -If the panel cover the it all around, it has to be remove to get to.
    -If it sit on the panel and screw or bolt to the frame. Just remove
    only the switch.

    Good Luck

    Mai

    Oct 07, 2013 | 2009 Volkswagen Tiguan

    1 Answer

    How to remove transfer case from 2002 tahoe


    • Disconnect the ground cable from the negative battery terminal, by using a wrench to loosen the retaining bolt and pulling the clamp off the terminal.

    • 2

      Raise the vehicle and support with jack stands placed underneath the frame.

    • 3

      Drain the transfer case. Locate the drain plug near the bottom of the transfer case. Place a waste oil collection pan underneath the plug and use a socket to remove it. Once all the fluid has drained out, reinstall the plug.

    • 4

      Remove the bolts that connect the rear driveshaft to the rear axle yoke using a socket. Lower the driveshaft, and slide it backward underneath the rear axle to disengage it from the transfer case. Remove it from the vehicle.

    • 5

      Remove the bolts that connect the front driveshaft to the front axle yoke using a socket. Lower the driveshaft, and slide it forward underneath the front axle to disengage it from the transfer case. Remove the driveshaft from the vehicle.

    Removing the Transfer Case
    • 1

      Label and disconnect the electrical wires and vacuum lines connected to the transfer case. Use masking tape and a marker.

    • 2

      Remove the transfer case shifter rod. Using needle-nose pliers, remove the clip that connects the shifter rod to the transfer case. Slide the rod away from the transfer case.

    • 3

      Position a floor jack underneath the transfer case. Raise it enough to take the weight of the transfer case off the transmission.

    • 4

      Remove the bolts that connect the transfer case to the transmission using a socket or wrench.

    • 5

      Slide the transfer case rearward to disengage it from the transfer case. Lower the floor jack, and remove the transfer case from the vehicle.


    Jan 20, 2012 | Cars & Trucks

    1 Answer

    When I refuel my 2011 Tiguan, I pump until it shuts off, then round to nearest dollar. By the time I'm home less than 4 miles, the needle drops off full by a needles width, is this normal in VWs?


    No this is not normal, you have a problem with the gas gauge sending unit inside the gas tank.The sending unit will need to be replaced, it is part of what is called the fuel pump module, quite an expensive part. I suggest based on the cost of this repair that if you can just live with this little glitch you do so.

    Oct 26, 2011 | 2011 Volkswagen Tiguan

    1 Answer

    How to change vw tiguan low beam bulb


    remove the front bumper to get access to remove the headlight

    Jul 19, 2011 | 2009 Volkswagen Tiguan

    1 Answer

    How to remove out side rear door handle on vw tiguan


    open door look inside for clips take off inside cover removes from inside under panel.

    Apr 21, 2011 | 2009 Volkswagen Tiguan

    1 Answer

    Where is the cabin air filter located on a 2009 US tiguan?


    Removal:
    - Remove footwell trim -1- on front passenger side.
    - Remove partition -2- from heating unit.
    - Release cover -3- in direction of -arrow-.
    - Remove dust and pollen filter downward out of heating unit.

    tdisline_8.png


    tdisline_9.png
    Install in reverse order of removal.


    Please do rate my response. Thanks!

    Feb 04, 2011 | 2009 Volkswagen Tiguan

    1 Answer

    Howcanyoutellimportonvwtouran


    I would imagine you could tell if a VW was imported or not by what units the speedo was in, km or mph.

    http://en.wikipedia.org/wiki/Volkswagen_Tiguan

    { ... The production Tiguan was released at the 2007 Frankfurt Motor Show, and debuted as a 2008 model for Europe and elsewhere and in North America as a 2009 model. Sales of the Tiguan in Canada began in April 2008.
    ...
    The import version of Tiguan appears on the Chinese market in 2009, but soon a locally built version (aka Shanghai-Volkswagen Tiguan) was revealed at 2009 Guangzhou Motor Show. The Chinese-built Tiguan uses 1.8TSI (118kW) and 2.0TSI (147kW), and has a revised front facia. At the same time the import Tiguan is still sold in China, which has 2.0TDI and R-Line kit as highlights. The basic design of the import model is the same as the international one. In order to differ locally-built and import models, Shanghai-VW Tiguan is given a Chinese name, known as ?? (tuguan), and the import one keeps the original letter name.
    ...}

    Jul 10, 2010 | 2009 Volkswagen Tiguan

    1 Answer

    Transfer case removal


    first remove both front and rear driveshafts. Then remove skid plate underneath transfer case. Remember to unplug the electric motor wiring harness for explorers with electronic four wheel drive switching. Remove vacuum line on the top of transfer case. Unbolt Speedometer cable mount from top/rear of transfer case. Remove five bolts connecting the transfer case to the transmission, this step will cause some transmission fluid to leak from the shaft housing (approx. half a litre) so place a drain pan underneath. Remember to either place a jack or wood blocking under transfer case before removing the last bolt connecting the transfer case as it is heavy (approx. 80-90 lbs.).

    May 12, 2010 | Cars & Trucks

    Not finding what you are looking for?
    2010 Volkswagen Tiguan Logo

    Related Topics:

    41 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Volkswagen Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    yadayada
    yadayada

    Level 3 Expert

    77499 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8826 Answers

    Are you a Volkswagen Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...