Question about Cars & Trucks

1 Answer

I have a 2000 chrysler concorde I bought a month ago used The check engine light came on did the key dance and got code P0070 Help pleeeeease Desperate girl here

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,679 Answers

This is code for the AMBIENT AIR TEMP SENSOR which as i understand controls the interior heating/cooling , try this link
http://www.2carpros.com/questions/chrysler-concorde-1998-chrysler-concorde-auto-temp-contro

Posted on Mar 29, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jgwhomeequip
  • 1902 Answers

SOURCE: rough idle and check engine light concord

Check your EGR valve and your IAC Idle Air Control valve make sure both are functioning correctly

Posted on Feb 15, 2009

  • 1 Answer

SOURCE: 2000 chrysler concorde switch unlocks but wont lock doors.

sounds like the actuator. I had the same problem. Mine got to the point where it will now only work with the key. Had it looked at by dealer.. actuator is bad. Good luck.

Posted on Apr 28, 2009

polarcycle
  • 1392 Answers

SOURCE: I have a 2000 chrysler concorde that the engine light just popped on - the error codes are po302, po420, po340

P0302-cylinder #2 misfire detected
P0420- catalyst efficiency below threshold bank 1
P0340-No cam signal at PCM.
The Cam sensor most likely needs to be replaced first. Clear the codes after that and drive and see what comes back on.

Posted on May 29, 2009

  • 412 Answers

SOURCE: i have a 2001 chrysler concorde. the trouble codes

I RECOMMEND REPLACING THE OUTPUT SPEED SENSOR..ABOUT 40 BUCKS..WILL CAUSE THESE OTHER FAULT CODES AS WELL

Posted on Aug 31, 2009

wracefans24
  • 1985 Answers

SOURCE: I have a 2005 Chrysler Town & Country with

there are no codes that say replace O2 sensors,or remove converter,Thats just somebody's guessing,When it says O2 sensor that tells the mechanic to look for trouble in that area,wiring or faulty readings,And there are four O2 sensors.

Posted on Jan 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Chrysler Concorde, The battery caused a fire, fixed that problem, but now check engine light comes on, and sputters a bit. Any suggestions?


The easiest way to figure this out is to read the touble code that triggered the check engine light.You will probably want to clear the code after making the correction,otherwise,it colud take a lot of ignition cycles to go out on its own.A basic code scanner is about 50 bucks,which will pay for itself in one use! The battery fire probably melted a nearby wire,connector,or sensor.

Aug 08, 2012 | 2000 Chrysler Concorde

1 Answer

I have a Chrysler concorde 2000 and the transmission light is on What could it mean


it means your car has the obd2 code problem, you need a scan tool to diagnose the code, and then delete the code, i know this tool is helpful for your car. or you can take it to the chrysler dealer, they will check for you, hope help.

Jul 09, 2011 | 2000 Chrysler Concorde

1 Answer

2000 chrysler concorde check engine light came on, dash lighs flash and transmission wont shift any ideas?


It sounds like you have a problem with your security system if you mean that it won't allow you to shift out of park. BUT you should start off getting the engine error code read so you will know what the car is trying to tell you. Anytime you get a check engine light, the vehicle generates an error code.

Since you probably can't drive it, you need to rent, borrow or buy an OBDII scanner and get that code, so it gives you a clue on where to begin the troubleshooting process.

Jul 04, 2011 | 2000 Chrysler Concorde

1 Answer

The check engine light stays on, I checked the gas cap,air filter they seem to be ok,Is there other things i can check, i dont want to bring it to the shop it's to costly, it happen once before a couple of...


I suggest that you start by taking the vehicle to a auto parts store and ask them to use a code scanner to check for diagnostic trouble codes. Most stores offer this service for free and it can help determine where to look for the problem.

Feb 06, 2011 | 1999 Chrysler Concorde

2 Answers

I have a 2000 concorde with a 3.2l i have a miss at idle and when car gets warm will die when coming to a stop. ive replaced the plugs and nothing. i have no check engine light on. i have unpluged the...


learn about key dance online

you turn the ignition
ON - OFF - ON - OFF - ON you have to do this in 7 seconds or less
the cluster is going to give you a computer code, that is your problem

the code 1624 is nothing it means the battery was unplug

good luck

Apr 01, 2010 | 2001 Chrysler Concorde

2 Answers

I have a 99 concorde runs good then out of no where rpms drop and a car will not get fuel,dies then will start some times soon or later and runs good


Change your Crankshaft position sensor, or your camshaft position sensor. Same thing happened on my car about 3 months ago.

Aug 05, 2009 | 1999 Chrysler Concorde

1 Answer

I have a 2000 chrysler concorde that the engine light just popped on - the error codes are po302, po420, po340


P0302-cylinder #2 misfire detected
P0420- catalyst efficiency below threshold bank 1
P0340-No cam signal at PCM.
The Cam sensor most likely needs to be replaced first. Clear the codes after that and drive and see what comes back on.

May 29, 2009 | 2000 Chrysler Concorde

1 Answer

1995 Chrysler Concorde


the alarm is activating when he locks it and for some reason the key or fob isnt deactivating it..check the disarm switches in the door

Aug 11, 2008 | 1995 Chrysler Concorde

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...