Question about 1998 Subaru Forester

1 Answer

Differance betwen intake and exhaust cams 2.5 subbaru

Mixed up by mistake

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Subaru Expert
  • 244 Answers

I don't know if you have the capability to zoom in on the picture I attached, But the cams are marked with R EX for right exhaust, R IN for right intake and L EX for left exhaust and L IN for left intake. The circles on the picture are showing where the marks will be on the cams. I hop this info helps!

differance betwen intake and exhaust cams 2.5 subb - b387032e-dc56-4140-84a7-9d23ff5a0c64.png

Posted on Mar 30, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a csmshsft sensor on a 2008 cadillac srx


Before you replace a part you may or may not need . Why ? What code ? Does the vehicle run ? There has been a lot of confusion on these vehicles with variable valve timing , mixing up cam sensors with camshaft actuators
DTC P0008: Engine Position System Performance Bank 1

DTC P0009: Engine Position System Performance Bank 2
The presence of DTCs P0008 and P0009 along with P0016, P0017, P0018, and P0019 indicates a possible condition with the primary timing chain and the alignment between both intermediate sprockets and the crankshaft. Or, the crankshaft reluctor wheel has moved and is no longer referenced to top dead center (TDC).


?€¢
Observe the scan tool CMP Desired, Actual, and Angle Variance parameters before a DTC sets. This may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.



DTC Descriptors
DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0020: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P0023: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P2088: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2089: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2090: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2091: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2092: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2093: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2

DTC P2094: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2095: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0342: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0343: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0346: Intake Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0347: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0348: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0367: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0368: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0391: Exhaust Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0392: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0393: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2
I'm sorry but when dealing with these problems your best bet is to take your vehicle to a qualified repair shop , I have never see a DIY'ER correct the problem with these , an in the end always end up taking it to the dealer .

Jul 24, 2016 | 2008 Cadillac Srx

1 Answer

Instruction changing timing belt 1979 Alfa Romeo Spider Veloz?


With Cam Caps loosened, FIRST loosen timing chain tensioner, press it in to loosen tension, Crank using ratchet to TDC (Top Dead Center on crank pully, (to keep from damage to pistons), align Exhaust Cam Timing Mark to mark on #1 Exhaust cam cover, then take up slack between Exhaust & Intake Cams (on top between the cams), Then align the Intake Cam to mark on #1 Cam Cap, "Now" loosen the 17mm bolt to tighten timing chain, rotate engine using rachet two times, reset TDC at the crank, and look at "Cam Timing Marks on both the Exhaust, and Intake Cams. If you did all this correctly the "Timing Marks" should be lined up so TDC,Exhaust, and Intake marks are all the same.

Oct 10, 2014 | 1979 Alfa Romeo

1 Answer

How to tell the intake cam from the exhaust cam o my 2008 Nissan titan


There should be a letter "E" for the exhaust side, and an "i" for the intake !
Sometimes barely visible !

Oct 03, 2014 | 2008 Nissan Titan

1 Answer

Replaced the heads with rebuilt heads on a 2000 Malibu . Idles a little rough and the exhaulst suxs back in too. Iv replaced all spark plugs and wires and new gaskets all the way up. What could cause this...


These engines have different size push rods for the exhaust valve, did you mix them up by mistake, that is a common problem, i am almost positive that exhaust push rods are a little longer than the intake ones, good day, let me know.

Oct 01, 2012 | Cars & Trucks

2 Answers

I have a 1999 Buick Century V6 3100 that I had to replace the intake gaskets due to antifreeze leaking into and out of the engine. When I had it all apart I noticed the very first lifter #2 cylinder...


If the engine oil was full of antifreeze when the intake gasket went bad, then there is a good chance that there may be some cam and/or lifter damage. A more likely cause of your problem would be that the push rods got mixed up when you put it back together. The intake and exhaust rods are different lengths. If this is the case, and you have turned the engine over, there is a good chance that you now also have a bent pushrod and intake valve. The exhaust pushrod is the longer one and if you mix them up, the piston will contact the intake valve because it will not be able to close due to the longer pushrod. This will bend or break the pushrod and bend the valve stem.

Jan 16, 2011 | 1999 Buick Century

2 Answers

My 2001 kia sportage misfires through the exhaust and through the intake, causing strong petrol fumes andfuel consumption is high


This sounds like an ignition timing problem, or a poorly performing ignition part. My best guess would be the coil pack if the timing is OK.

Nov 10, 2010 | Kia Sportage Cars & Trucks

1 Answer

My crank shaft is rotating twise the crank shaft. HOW MY 1342 FIRING WILL OCCURE?, I can spare only 30 digree for charge and spark plug contact. THERE ARE ONLY 2+2 CYLINDER. 180 DIGREE APPART KINDLY REPLY...


Your crankshaft turns 2x times the camshaft. Put it this way as # 1 cylinder reaches TDC (top dead center) of the firing/compression stroke, and this will be after a (8 degs BTDC) spark to ignite the air/fuel mix, the # 3 cyl. will be at BDC of the intake stroke and as #1 begins its power down stroke, (during explosion of air/fuel mix), #3 begins its compression up stroke, the #4 cyl. will be coming down with #1 cyl. but #4 will be in the beginning of its intake down stroke, and #2 cyl. will be coming up with #3 but #2will be in its BDC of the exhaust stroke. Which has just fired previously to #1. 1342134213421342 etc. Now the cam turns to open / close the valves; In the outline above, #1 cyl. valves will both be closed. #3 cyl. will have the intake starting to close at this point. #4 cyl. will just be starting to open its intake valve, and #2 will be starting to open its exhaust valve. Is all this clear as mud? So as the crank makes one full rotation (in a 4cyl. engine) only the firing of one cylinder has happened.and at every rotation one cyl. will fire. So #1 at TDC then one full rotation, #1 back at TDC, but this TDC is half of its 4 cycles, (1)Intake, (2)compression, (3)power, (4)exhaust. this 1234 refers to the 4 cycles of the rotation not firing order.

Oct 31, 2010 | 2008 Volkswagen Jetta

1 Answer

What happens when i mix 10w-30 with 20w-50 in the


You mixed two different oil weights (BIG NO NO) GOOD luck on the prognosis

Nov 04, 2009 | 1996 Mercury Mystique

1 Answer

Which order do the push rods go in for 1999 chevorelet venture , i know there are the intake and exhaust pushrods , but they got mixed up when laid out


Well check them and see if there the same ,,
If they are then it dosent make any differance were they go but if they are not the same then check the rockers and you might find the rockers on inlet are shorter than the exhaust,
Put in the holes push down to cam follower and rest against rocker and it should rest about were the cup on push rod Sits.

Oct 02, 2009 | 1999 Chevrolet Venture

Not finding what you are looking for?
1998 Subaru Forester Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...