Question about 2004 Nissan 350Z

Open Question

Code p1815 Service engine like code P1815

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I repair the four wheel drive on a 1999 Ford Ranger XLT?


It depends on what is wrong , is the 4x4 light flashing ? Are you aware of the complexity of the 4x4 system ? Has a electronic control module , has the ability to set an store DTC'S - diagnostic trouble codes !
Transfer Case The four wheel drive system is an electronic shift 4X4 system that allows the operator to choose between three different modes. The operator can switch 4X4 HIGH modes at any speed. To engage or disengage 4X4 LOW the vehicle speed must be less than 5 kph (3 mph), the brake depressed, and the transmission must be in NEUTRAL.
The shift motor sense plate, an integral part of the electronic shift motor, informs the generic electronic module (GEM) of the transfer case shift motor and contact plates A, B, C and D position.
The digital transmission range (TR) sensor is located on the LH side of the transmission, and informs the GEM when the transmission is in the NEUTRAL position.
The electronic shift motor is mounted externally at the rear of the transfer case. It drives a rotary cam which moves the mode fork and range fork within the transfer case between the 4X4 HIGH, 4X4 LOW and 2WD range positions.
When the GEM verifies the completion of the transfer case shift from 2WD to 4X4 HIGH (reading the contact plate positions), the GEM will then energize both pulse vacuum hublock (PVH) solenoids (supplying ground for 45 seconds). The PVH solenoid will allow a HIGH flow of intake manifold vacuum to the "wheel end hublocks", engaging the wheel end hubs to the front differential and transfer case to achieve four wheel drive.
Here are just a few DTC'S the system can set an store in the module !
P1804 4WD High Indicator Circuit Failure GEM GO to Pinpoint Test C . P1806 4WD High Indicator Short to Battery GEM GO to Pinpoint Test C . P1808 4WD Low Indicator Circuit Failure GEM GO to Pinpoint Test C . P1810 4WD Low Indicator Short to Power GEM GO to Pinpoint Test C . P1812 4WD Mode Select Switch Circuit Failure GEM GO to Pinpoint Test A . P1815 4WD Mode Select Switch Circuit Short to Ground GEM GO to Pinpoint Test A . P1820 Transfer Case CW Shift Relay Circuit - Failure GEM GO to Pinpoint Test A . P1822 Transfer Case CW Shift Relay Coil Short to Power GEM GO to Pinpoint Test A . P1824 4WD Electric Clutch Relay Circuit Failure GEM GO to Pinpoint Test A . P1826 4WD Low Clutch Relay Short to Power GEM GO to Pinpoint Test A . P1828 Transfer Case CCW Shift Relay Coil Circuit Failure GEM GO to Pinpoint Test A . P1830 Transfer Case CCW Shift Relay Coil Short to Battery GEM GO to Pinpoint Test A . P1838 Transfer Case Shift Motor Circuit Failure GEM GO to Pinpoint Test A . P1846 Transfer Case CONTACT PLATE "A" Circuit Failure GEM GO to Pinpoint Test A . Now are you sure you really want to mess with this ? You would need a factory diagnostic scan tool to check this out before you start replacing parts !
Here

May 30, 2015 | Ford Ranger Cars & Trucks

2 Answers

How to reset Service Engine Soon light after replacing gas cap? Took to AutoZone when the Service Engine Soon light came on Error code P0440.


Disconnect the negative battery cable for 30 minutes. Reconnect after and the code will clear. However if the problem persists, the code will come back with in 20 miles or 30 minutes.

Aug 02, 2014 | 2000 Buick Regal LS

1 Answer

4x4 low light on car will not move


The electronic module (located behind the glove compartment) controls the operation of the transfer case in response to inputs from the electric shift motor, 4x4 mode switch, CPP switch, BPP switch, DTR sensor, throttle position output from the PCM, front and rear OSS sensors, and the VSS. Do you know what DTC'S Are ? Diagnostic trouble codes !

P1804 4WD High Indicator Circuit Failure GEM GO to Pinpoint Test C . P1806 4WD High Indicator Short to Battery GEM GO to Pinpoint Test C . P1808 4WD Low Indicator Circuit Failure GEM GO to Pinpoint Test C . P1810 4WD Low Indicator Short Circuit to Battery GEM GO to Pinpoint Test C . P1812 4WD Mode Select Circuit Failure GEM GO to Symptom Chart. P1815 4WD Mode Select Short Circuit to Ground GEM GO to Symptom Chart. P1820 Transfer Case CW Shift Relay Coil Circuit Open or Short to Ground GEM GO to Pinpoint Test B . P1822 Transfer Case CW Shift Relay Coil Short to Battery GEM GO to Pinpoint Test B . P1824 4WD Electric Clutch Relay Circuit Failure GEM GO to Pinpoint Test A . P1826 4WD Electric Clutch Relay Short to Battery GEM GO to Pinpoint Test A . P1828 Transfer Case CCW Shift Relay Circuit Failure GEM GO to Pinpoint Test B . P1830 Transfer Case CCW Shift Relay Coil Short to Battery GEM GO to Pinpoint Test B . P1836 Transfer Case Front Shaft Speed Sensor Circuit Failure GEM GO to Symptom Chart. P1837 Transfer Case Rear Shaft Speed Sensor Circuit Failure GEM GO to Symptom Chart. P1838 Transfer Case Shift Motor Circuit Failure GEM GO to Pinpoint Test B . P1846 Transfer Case CONTACT PLATE "A" Circuit Failure GEM GO to Pinpoint Test B . P1850 Transfer Case CONTACT PLATE "B" Circuit Failure GEM GO to Pinpoint Test B .

P1854 Transfer Case CONTACT PLATE "C" Circuit Failure (GEM Only) GEM GO to Pinpoint Test B . P1858 Transfer Case CONTACT PLATE "D" Circuit Failure (GEM Only) GEM GO to Pinpoint Test B . P1866 Transfer Case Maintenance Required (GEM Only) (4-wheel drive operation can be restored by clearing the DTC and cycling the ignition.) GEM GO to Pinpoint Test B . P1867 Transfer Case Contact Plate General Circuit Failure (GEM Only) GEM GO to Pinpoint Test B . P1874 Automatic Hall Effect Sensor Power Circuit Failure GEM GO to Symptom Chart. P1875 Automatic Hall Effect Sensor Power Circuit Short to Battery (GEM Only) GEM GO to Symptom Chart. P1891 Transfer Case Contact Plate Ground Return Open Circuit GEM GO to Pinpoint Test B Your best bet , take it to a qualified repair shop

Apr 04, 2017 | 2002 Ford Explorer

1 Answer

My 1998 pontiac firebird service engine light came on and my OBD11 scanner produced 2 trouble codes PO125 ( insufficient coolant temperature for closed loop fuel control.the 3800V6 engine over heating and...


service the engine.. change oil ,filter plugs etc

did you clear the faults before each read
Diagnose Buick 3800 Engine
unusual code that

P0125 is the OBD-II generic code for the engine computer, or Engine Control Module (ECM), not detecting enough heat in the cooling system before the fuel management system can take control. The ECM has a predetermined value after you start your vehicle to expect a certain coolant temperature

P0125 OBD II Trouble Code Insufficient Coolant Temperature for Closed Loop...

ecm runs the engine cooling fans

3800V6 engine over heating and heater produces cold air
try these

EGR vale not working
overheating
inlet manifold gasket leaking
water pump fins corroded
soft radiator hoses
try a new radiator cap

internal heating
heater control tap stuck
directional actuator flaps stuck

Apr 16, 2017 | Cars & Trucks

1 Answer

Service engine, abs, trac off


The service engine light does not affect the abs.You most likely have a broken wire in your abs system which is affected by suspension movement.A code reader which does abs codes will tell you which wheel circuit is turning on the abs light.When there is no abs available the track will turn off.

Jul 03, 2017 | 2000 Pontiac Grand Am GT

1 Answer

What does the "service engine now" light mean?


Keep in mind that two warning there, Check Engine and Service Engine Soon; Check Engine means there is a malfunction... Service Soon is reprogrammable, when you change you oil.

"Check Engine" are refer to the emission codes, but not always. I suggest visit some autozone ot autoshop with scan tools or "reader code" to know exactly what fault code is stored there. With this code number we could send you additional details.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 05, 2011 | 1991 Cadillac Seville

1 Answer

Wont idle sounds rattley code 1815 put used one on same thing replaced plugs wires checked rod bearings timing belt could imrc still make it not idle?


P1815 Transmission 4-Wheel Drive Mode Select Short Circuit To Ground, have you checked or clean the idle air control! ( IAC ). this controls idling.

Sep 17, 2011 | 1997 Ford Escort

1 Answer

Getting code p 1815 with check engine ligth on


Diagnostic Test Code (DTC) P1815 indicates that the Powertrain Control Module (PCM) has detected an electrical failure in the Transmission Fluid Presure (TFP) manual valve position switch or the circuits between this switch assembly (located INSIDE the transmission) and the PCM.

There are several Technical Service Bulletins (TSBs) for your transmission. One that specifically addresses this code is TSB NUMBER 03-07-30-021A
This TSB involves reprogramming of the PCM to correct certain issues associated with DTC P1815 and other DTCs.

Aug 09, 2011 | 2003 Chevrolet Malibu

1 Answer

Service Engine Light not illuminated


The check engine light is turned on by the ECM. (computer) Make sure the bulb is good. For a 1989 you don't need a code reader, just an ALDL grounding tool to read out codes.

May 17, 2009 | 1989 Chevrolet S-10 Blazer

Not finding what you are looking for?
2004 Nissan 350Z Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...