Question about 2006 Mercedes-Benz Vito 112

Open Question

C1011 FAULT ON VITO

NEED TO CLEAR FAULT ,

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to clear check engine light


You need a scan tool to clear codes.

But doing this is a pointless exercise as the CE warning light will come back next time you drive the vehicle unless you deal with the problems that are generating the fault codes and CE in the first place.

If you have replaced parts (because some one told you XYZ fault code = replace ABC part) you thought were causing the problems and you are still getting the CE and fault codes then your diagnosis of the problem was completely wrong.

Jan 09, 2016 | 1999 Jeep Grand Cherokee

1 Answer

What do you do to clear an active fault code reading transmission controller not responding


You need a code reader that has the capacity to clear fault codes. Auto Zone will lend you one

Oct 10, 2014 | Cars & Trucks

2 Answers

Reset check engine light on a 2008 Buick Enclave without going to a garage


Anyone with a scanner can erase the codes and reset the light. On older cars, you could just remove the negative battery post for a few minutes, but that is not recommended for newer cars. Erase codes with a scanner.

Dec 09, 2013 | Cars & Trucks

1 Answer

I am working on a friends 2010 harley 48. he had it fall on the left side, and now it wont start and keeps blowing the 15 amp fuse for the lights and has codes p0261 and p0263 and p1003 that come back as...


some fault codes stored in your car, you can go to garage clear the fault codes or get code scan tool to clear it.
what model and year of your car? if you need code scan tool you can go to chinasinoy

Jun 28, 2012 | Cars & Trucks

1 Answer

My 07 trailblazer has a code p0526, what does that mean?


This is a fault in the fan speed sensor circuit. You may need to check the connector or replace this sensor. Remember to have someone clear the computer. Some defects will clear automatically and others need time or a scanner to clear.

Feb 23, 2012 | 2007 Chevrolet TrailBlazer SS

1 Answer

1992 jaguar vandreplas in limpe mode


This is caused usually by either multiple fault codes triggered or one(s) of a serious nature.You will need to make contact with a garage or dealer that can successfully read these and hopefully clear them.Any that don't clear will need repair in those areas,others that cleared should at least be inspected for obvious signs of fault,or make note of for later in case they return.Sometimes the fault can be in the ECU or the loom to it.check for dampness around it and poor connection in ecu loom plugs and its earth.I hope that this is of some help to you in getting to the source and repair.

Mar 30, 2011 | Jaguar Vanden Plas Cars & Trucks

1 Answer

I just had my Ford serviced about 2 mos ago. The service engine light just came on and is staying on. I took my Ford to AutoZone. They tested it and said that the anitfreeze needed to be changed.. We...


You need to reset (clear) the fault code, assuming the antifreeze change solved the problem. Frankly I don't know of a fault code that points out antifreeze. You can clear the fault by 1: Removing the Negative terminal from your battery for about a minute and replace, or 2: Take it back to AutoZone and have them clear the fault for you (free). If it comes back on, I would write down the code and research it on the internet, again the antifreeze thing sounds strange.

Jan 04, 2011 | 2003 Ford Expedition

1 Answer

How do you clear trouble codes on a 94 GM 6.5 diesel? Disconnecting battery power does not do it.


Take it to autozone or a major auto supply house and have them use the fault code reader to read it for you, they usually do this for free and will tell you what the error codes are if it is something simple it can possibly be repaired right there and if not you need to take it to a mechanic. Disconnecting the battery will not clear a fault if the fault still exists.

I hope this helps you with your issue.

Stormi

Nov 13, 2010 | 1994 Chevrolet Silverado 2500

1 Answer

How do I reset the check engine light on a 1997 VW Jetta


either you will need a diag machine to plug in and clear the fault code providing the fault has been rectified if not it will not clear as the ecu will still see the fault if the fault has been repaired disconecting the battey for ten min may work or the light should go out over time vw specifiy 200 cycles of the ignition with out the fault re-occouring

May 03, 2010 | 1997 Volkswagen Jetta

1 Answer

'99 XJR Gear Box Fault


whats the fault code in the tcm? you should only need to clear the codes

May 26, 2017 | Jaguar Cars & Trucks

Not finding what you are looking for?
2006 Mercedes-Benz Vito 112 Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76691 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...